Infiniti QX56 (Z62). Manual - part 1225

SRC-104

< DTC/CIRCUIT DIAGNOSIS >

B1115 SATELLITE SENSOR RH

NO

>> INSPECTION END

B1116 SATELLITE SENSOR RH

SRC-105

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1116 SATELLITE SENSOR RH

DTC Logic

INFOID:0000000006220042

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III.

 Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-14, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-105, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006220043

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

1.

REPLACE FRONT SATELLITE SENSOR

1.

Replace front satellite sensor RH. Refer to 

SR-24, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-105, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 2. 

NO

>> INSPECTION END

2.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-26, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-105, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1. 

NO

>> INSPECTION END

DTC

Display contents of 

CONSULT-III

DTC detecting condition

Possible cause

B1116

SATELLITE SENS RH 
[UNMATCH]

Front satellite sensor RH is out of the spec-
ified specification

Diagnosis sensor unit or front satellite sensor RH 
is different from the part specified

SRC-106

< DTC/CIRCUIT DIAGNOSIS >

B1118, B1119 SATELLITE SENSOR LH

B1118, B1119 SATELLITE SENSOR LH

DTC Logic

INFOID:0000000006220044

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III.

 Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-14, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-106, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006220045

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3. 

NO

>> Replace wiring harness.

3.

REPLACE FRONT SATELLITE SENSOR

1.

Replace front satellite sensor LH. Refer to 

SR-24, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-106, "DTC Logic"

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-26, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-106, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1. 

DTC

Display contents of 

CONSULT-III

DTC detecting condition

Possible cause

B1118
B1119

SATELLITE SENS LH
[UNIT FAIL]

Front satellite sensor LH is malfunctioning

• Disconnection of wiring harness
• Malfunction in front satellite sensor LH
• Malfunction in air bag diagnosis sensor unit

B1118, B1119 SATELLITE SENSOR LH

SRC-107

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

NO

>> INSPECTION END