Infiniti Q45. Manual - part 874

 

  Index      Infiniti     Infiniti Q45 - service repair manual 2006 year

 

Search            copyright infringement  

 

 

 

 

 

 

 



 

 

Content   ..  872  873  874  875   ..

 

 

Infiniti Q45. Manual - part 874

 

 

COLLISION DIAGNOSIS

SRS-53

C

D

E

F

G

I

J

K

L

M

A

B

SRS

For Side Collision

NHS0004X

WHEN THE SIDE AIR BAG IS ACTIVATED IN THE SIDE COLLISION:

1.

Replace the following components:

All parts of front seatback (including front seat back frame) with front side air bag module (on the side on
which front side air bag is activated)

Curtain air bag module (on the side on which side curtain air bag is activated)

Diagnosis sensor unit

Satellite sensor (on the side on which side air bag and side curtain air bag is activated)

2.

Check the SRS components and the related parts using the following table.

Replace any SRS components and the related parts showing visible signs of damage (dents, cracks,
deformation).

3.

Conduct self-diagnosis using CONSULT-II or “AIR BAG” warning lamp. Refer to 

SRS-21, "SRS Operation

Check"

 . Ensure entire SRS operates properly.

WHEN SRS IS NOT ACTIVATED IN THE SIDE COLLISION:

1.

Check the SRS components and the related parts using the following table.

Replace any SRS components and the related parts showing visible signs of damage (dents, cracks,
deformation).

2.

Conduct self-diagnosis using CONSULT-II or “AIR BAG” warning lamp. Refer to 

SRS-21, "SRS Operation

Check"

 . Ensure entire SRS operates properly.

SRS INSPECTION (FOR SIDE COLLISION)

Part

Front side air bag and 

side curtain air bag is 

activated

Front side air bag and side curtain air bag is NOT activated

LH or RH side curtain 
air bag module

REPLACE the side 
curtain air bag mod-
ule.
(Repair the center pil-
lar inner, etc. before 
installing new one if 
damaged.)

1. Check for visible signs of damage (dents, tears, deformation) of the center pillar on 

the collision side.

2. If damaged— Remove LH or RH side curtain air bag module.

3. Check for visible signs of damaged (tears etc.) of LH or RH side curtain air bag 

module.

4. Check harness and connectors for damage, and terminals for deformities.

5. If no damage is found, reinstall LH or RH side curtain air bag module with new 

bolts.

6. If damaged—REPLACE LH or RH side curtain air bag module with new bolts.

Front LH or RH side 
air bag module

REPLACE all parts of 
seatback with 
deployed front side 
air bag module.

1. Check for visible signs of damage (dents, tears, deformation) of the seatback on 

the collision side.

2. If damaged—REPLACE the damaged seat parts with new bolts and remove the 

front side air bag module.

3. Check for visible signs of damaged (tears etc.) of the front side air bag module.

4. Check harness and connectors for damage, and terminals for deformities.

5. If no damaged is found, reinstall the front side air bag module with new torx nuts 

coated with bonding agent.

6. If damaged—REPLACE the front seatback assembly.

Front LH or RH side 
air bag (Satellite) sen-
sor

REPLACE front LH or 
RH side air bag (Sat-
ellite) sensor on the 
collision side with 
new nuts.
(Repair the center pil-
lar inner, etc. before 
installing new one if 
damaged.)

1. Remove the front LH or RH side air bag (Satellite) sensor on the collision side. 

Check harness connectors for damage, terminals for deformities, and harness for 
binding.

2. Check for visible signs of damage (dents, cracks, deformation) of front LH or RH 

side air bag (Satellite) sensor.

3. Install front LH or RH side air bag (Satellite) sensor to check fit.

4. If no damage is found, reinstall front LH or RH side sir bag (Satellite) sensor with 

new nuts.

5. If damaged—REPLACE front LH or RH side air bag (Satellite) sensor with new 

nuts.

SRS-54

COLLISION DIAGNOSIS

Diagnosis sensor unit

REPLACE the diag-
nosis sensor unit with 
the new bolts.

1. Check case and bracket for dents, cracks or deformities.

2. Check connectors for damage, and terminals for deformities.

3. If no damage is found, reinstall the diagnosis sensor unit with new bolts and ground 

bolt.

4. If damaged—REPLACE the diagnosis sensor unit with new bolts and ground bolt.

Seat belt pre-
tensioner assembly

1. Check if the seat belt can be extended smoothly.

If the seat belt cannot be extended smoothly,

Check for deformities of the center pillar inner.

If the center pillar inner has no damage, Replace the seat belt pre-tensioner assembly.

2. Remove the seat belt pre-tensioner assembly on the collision side. Check harness cover and connectors 

for damage, terminals for deformities, and harness for binding.

3. Check for visible signs of damage (dents, cracks, deformation) of the seat belt pre-tensioner assembly.

4. Check seat belt adjuster for damage.

5. If no damage is found, reinstall the seat belt pre-tensioner assembly.

6. If damaged—REPLACE the seat belt pre-tensioner assembly with new bolts.

Seat with front side 
air bag

REPLACE all parts of 
front seatback 
(including front seat-
back frame)

1. Visually check the seat on the collision side.

2. Remove the seat on the collision side and check the following for damage and 

deformities.

Harness, connectors and terminals

Frame and recliner (for front and rear seat), and also adjuster and slides (for front 
seat)

3. If no damage is found, reinstall the seat.

4. If damaged—REPLACE the damaged seat parts using new bolts.

Center inner pillar

1. Check the center inner pillar on the collision side for damage (dents, cracks, deformation).

2. If damaged—REPAIR the center inner pillar.

Trim/headlining

1. Check for visible signs of damage (dents, cracks, deformation) of the interior trim on the collision side.

2. If damaged—REPLACE the damaged trim parts.

Part

Front side air bag and 

side curtain air bag is 

activated

Front side air bag and side curtain air bag is NOT activated

STC-1

STEERING CONTROL SYSTEM

G  STEERING

CONTENTS

C

D

E

F

H

I

J

K

L

M

SECTION 

STC

A

B

STC

STEERING CONTROL SYSTEM

WITHOUT REAR ACTIVE STEER

PRECAUTIONS .......................................................... 4

Precautions for Supplemental Restraint System 
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 4
Precautions .............................................................. 4

ELECTRICALLY CONTROLLED POWER STEER-
ING SYSTEM  .............................................................. 5

Power Steering Control Diagram .............................. 5
Operation Principle ................................................... 5

DURING PARKING (WHEN TURNING THE 
STEERING WHEEL TO THE RIGHT.)  .................. 5
DURING HIGH-SPEED OPERATION ................... 6

System Description  .................................................. 6

DESCRIPTION ...................................................... 6
POWER STEERING SOLENOID VALVE .............. 6
CONTROL UNIT  ................................................... 6

System Diagram ....................................................... 7

COMPONENTS FUNCTION DESCRIPTION  ....... 7

TROUBLE DIAGNOSIS .............................................. 8

Fail-Safe Function  .................................................... 8

FAIL-SAFE INPUT CONDITIONS ......................... 8

How to Perform Trouble Diagnosis  .......................... 8

BASIC CONCEPT  ................................................. 8

Component Parts Location ....................................... 9
Wiring Diagram — EPS —  ..................................... 10
Active Damper Suspension Control Unit Input/Out-
put Signal Reference Values  .................................. 12

ACTIVE DAMPER SUSPENSION CONTROL 
UNIT INSPECTION TABLE ................................. 12

CONSULT-II Function (ACT D/SUS)  ...................... 13

FUNCTION .......................................................... 13
CONSULT-II SETTING PROCEDURE ................ 13
SELF-DIAG RESULT MODE  .............................. 13
DATA MONITOR MODE  ..................................... 14

Self-Diagnostic Procedure  ..................................... 14

SELF-DIAGNOSTIC PROCEDURE (WITH 
CONSULT-II) ....................................................... 14
SELF-DIAGNOSTIC PROCEDURE (WITHOUT 

CONSULT-II) ....................................................... 14
ERASE SELF-DIAGNOSIS  ................................. 15

Inspections before Trouble Diagnosis  .................... 16
Trouble Diagnosis Chart for Symptoms .................. 16

TROUBLE DIAGNOSIS FOR SYSTEM .................... 17

Power Supply Circuit  .............................................. 17

ACTIVE DAMPER SUSPENSION CONTROL 
UNIT TERMINALS AND REFERENCE VALUE ... 17
DIAGNOSTIC PROCEDURE  .............................. 18

Vehicle Speed Sensor (VEHICLE SPEED SEN) .... 19

CONSULT-II REFERENCE VALUE IN DATA 
MONITOR MODE ................................................ 19
ACTIVE DAMPER SUSPENSION CONTROL 
UNIT TERMINALS AND REFERENCE VALUE ... 19
DIAGNOSTIC PROCEDURE  .............................. 20

Power Steering Solenoid Valve  .............................. 21

CONSULT-II REFERENCE VALUE IN DATA 
MONITOR MODE ................................................ 21
ACTIVE DAMPER SUSPENSION CONTROL 
UNIT TERMINALS AND REFERENCE VALUE ... 21
DIAGNOSTIC PROCEDURE  .............................. 22

Engine Speed Signal  .............................................. 24

CONSULT-II REFERENCE VALUE IN DATA 
MONITOR MODE ................................................ 24
ACTIVE DAMPER SUSPENSION CONTROL 
UNIT TERMINALS AND REFERENCE VALUE ... 24
DIAGNOSTIC PROCEDURE  .............................. 24

Component Inspection ............................................ 27

POWER STEERING SOLENOID VALVE ............ 27

TROUBLE DIAGNOSIS FOR SYMPTOMS  .............. 28

Hard Steering When Fully Turning the Steering 
Wheel ..................................................................... 28

DIAGNOSTIC PROCEDURE  .............................. 28

Light Steering When Driving at a High Speed  ........ 29

DIAGNOSTIC PROCEDURE  .............................. 29

CONTROL UNIT  ....................................................... 30

Removal and Installation  ........................................ 30

REMOVAL ........................................................... 30
INSTALLATION ................................................... 30

STC-2

WITH REAR ACTIVE STEER

PRECAUTIONS ......................................................... 31

Precautions for Supplemental Restraint System 
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ................................................................. 31
Precautions ............................................................. 31
Precautions for RAS Actuator Assembly and Rear 
Wheel Steering Angle Sensor Replacement  .......... 32

ELECTRICALLY CONTROLLED POWER STEER-
ING ............................................................................ 33

Power Steering Control Diagram  ............................ 33
Operation Principle  ................................................. 33

DURING PARKING (WHEN TURNING THE 
STEERING WHEEL TO THE RIGHT.)  ................ 33
DURING HIGH-SPEED OPERATION  ................. 34

System Description ................................................. 34

DESCRIPTION .................................................... 34
POWER STEERING SOLENOID VALVE  ............ 34
CONTROL UNIT .................................................. 34

System Diagram  ..................................................... 35

COMPONENTS FUNCTION DESCRIPTION ...... 35

CAN Communication  .............................................. 35

SYSTEM DESCRIPTION  .................................... 35

REAR ACTIVE STEER SYSTEM .............................. 36

Power Steering Control Diagram  ............................ 36
Operation Principle  ................................................. 36

OPERATION PRINCIPLE .................................... 36

System Description ................................................. 37

DESCRIPTION .................................................... 37
RAS ACTUATOR ASSEMBLY ............................. 37
STEERING ANGLE SENSOR  ............................. 37
REAR WHEEL STEERING ANGLE SENSOR  .... 37
CONTROL UNIT .................................................. 38
RAS WARNING LAMP  ........................................ 38

System Diagram  ..................................................... 38

COMPONENTS FUNCTION DESCRIPTION ...... 39

CAN Communication  .............................................. 39

SYSTEM DESCRIPTION  .................................... 39

TROUBLE DIAGNOSIS  ............................................ 40

Fail-Safe Function  .................................................. 40
How to Perform Trouble Diagnosis  ......................... 40

BASIC CONCEPT  ............................................... 40

Component Parts Location  ..................................... 41
Circuit Diagram  ....................................................... 42
Wiring Diagram — RAS —  ..................................... 43
RAS Control Unit Input/Output Signal Reference 
Values ..................................................................... 47

RAS CONTROL UNIT INSPECTION TABLE  ...... 47

CONSULT-II Function (RAS/HICAS)  ...................... 49

FUNCTION .......................................................... 49
CONSULT-II SETTING PROCEDURE  ................ 49
SELF-DIAG RESULT MODE  ............................... 49
DATA MONITOR MODE  ...................................... 51
ACTIVE TEST MODE .......................................... 52
RAS CONTROL UNIT PART NUMBER MODE ... 53

Self-Diagnostic Procedure  ...................................... 53

SELF-DIAGNOSTIC PROCEDURE (WITH 
CONSULT-II) ....................................................... 53

SELF-DIAGNOSTIC PROCEDURE (WITHOUT 
CONSULT-II) ........................................................53
ERASE SELF-DIAGNOSIS ..................................54

Inspections before Trouble Diagnosis .....................55
Trouble Diagnosis Chart for Symptoms  ..................55

TROUBLE DIAGNOSIS FOR SYSTEM  ....................56

DTC C1900, C1901, C1905, C1906, C1907, 
C1908, C1922, C1927, C1928 CONTROL UNIT ....56

DIAGNOSTIC PROCEDURE ...............................56

DTC C1925 AD CONVERTER  ...............................56
DTC C1902, C1903, C1904, C1910, C1913 
MOTOR OUTPUT  ...................................................57

CONSULT-II REFERENCE VALUE IN DATA 
MONITOR MODE  ................................................57
RAS CONTROL UNIT TERMINALS AND REF-
ERENCE VALUE  .................................................57
DIAGNOSTIC PROCEDURE ...............................58

DTC C1909 CONTROL UNIT  .................................60

CONSULT-II REFERENCE VALUE IN DATA 
MONITOR MODE  ................................................60
RAS CONTROL UNIT TERMINALS AND REF-
ERENCE VALUE  .................................................60
DIAGNOSTIC PROCEDURE ...............................60

DTC C1911, C1912 MOTOR VOLTAGE  .................62

CONSULT-II REFERENCE VALUE IN DATA 
MONITOR MODE  ................................................62
RAS CONTROL UNIT TERMINALS AND REF-
ERENCE VALUE  .................................................62
DIAGNOSTIC PROCEDURE ...............................62

DTC C1914, C1915, C1916, C1917, C1918 RR ST 
ANGLE SENSOR ....................................................67

CONSULT-II REFERENCE VALUE IN DATA 
MONITOR MODE  ................................................67
RAS CONTROL UNIT TERMINALS AND REF-
ERENCE VALUE  .................................................67
DIAGNOSTIC PROCEDURE ...............................68

DTC C1919 VEHICLE SPEED SEN  .......................72

DIAGNOSTIC PROCEDURE ...............................72

DTC C1920, C1923, C1924, C1926 STEERING 
ANGLE SEN  ...........................................................72

DIAGNOSTIC PROCEDURE ...............................72

DTC C1921 ENG REV SIGNAL ..............................73

DIAGNOSTIC PROCEDURE ...............................73

DTC C1929 VDC  ....................................................74

DIAGNOSTIC PROCEDURE ...............................74

DTC U1000 CAN COMM  ........................................75

DIAGNOSTIC PROCEDURE ...............................75

DTC U1010 CONTROL UNIT (CAN)  ......................75

DIAGNOSTIC PROCEDURE ...............................75

RAS Actuator Assembly ..........................................76

DIAGNOSTIC PROCEDURE ...............................76

Power Steering Solenoid Valve  ...............................77

CONSULT-II REFERENCE VALUE IN DATA 
MONITOR MODE  ................................................77
RAS CONTROL UNIT TERMINALS AND REF-
ERENCE VALUE  .................................................77
DIAGNOSTIC PROCEDURE ...............................78

Stop Lamp Switch  ...................................................80

CONSULT-II REFERENCE VALUE IN DATA 

 

 

 

 

 

 

 

Content   ..  872  873  874  875   ..