Infiniti M35/M45 Y50. Manual - part 84

ON-VEHICLE SERVICE

AT-259

D

E

F

G

H

I

J

K

L

M

A

B

AT

13. Remove return spring (1) from parking pawl (2).

Inspection

●

If the contact surface on parking actuator support, parking pawl,
etc. has excessive wear, abrasion, bend, or any other damage,
replace the components.

Installation

CAUTION:

After completing installation, check A/T fluid leakage, A/T fluid level and A/T position. Refer to 

AT-13,

"Checking A/T Fluid"

 , 

AT-228, "Checking of A/T Position"

 .

1.

Install return spring (1) to parking pawl (2).

SCIA6180J

SCIA5143E

SCIA5144E

SCIA6180J

AT-260

ON-VEHICLE SERVICE

2.

Install parking pawl (with return spring) (1) and pawl shaft (2) in
output shaft & companion flange complement.

3.

Install parking actuator support (1) in output shaft & companion
flange complement.

4.

Apply recommended sealant (Genuine Anaerobic Liquid Gasket
or equivalent. Refer to 

GI-47, "Recommended Chemical Prod-

ucts and Sealants"

 .) to output shaft & companion flange com-

plement as shown in the figure.

CAUTION:

Completely remove all moisture, oil and old sealant, etc.
from the transmission case and output shaft & companion
flange complement mounting surfaces.

5.

Install output shaft & companion flange complement to transmis-
sion case.

6.

Tighten output shaft & companion flange complement bolts (1)
to the specified torque. Refer to 

AT-257, "Components"

 .

: Bolt (10)

CAUTION:

Do not reuse self-sealing bolts (2).
Refer to GI section to make sure icons (symbol marks) in the fig-
ure. Refer to 

GI-11, "Components"

 .

SCIA7066E

SCIA7065E

SCIA5212E

SCIA5688E

SCIA6943E

ON-VEHICLE SERVICE

AT-261

D

E

F

G

H

I

J

K

L

M

A

B

AT

7.

Install engine mounting insulator (rear). Refer to 

AT-274, "Removal and Installation (2WD Models)"

 .

8.

Install rear engine mounting member. Refer to 

AT-274, "Removal and Installation (2WD Models)"

 .

9.

Install control rod. Refer to 

AT-226, "Control Rod Removal and Installation"

 .

10. Install rear propeller shaft. Refer to 

PR-8, "Removal and Installation"

 .

11. Install exhaust front tube and center muffler. Refer to 

EX-7, "Removal and installation"

 .

12. Install drain plug to oil pan. Tighten a necessary drain plug with specified torque. Refer to 

AT-236, "Control

Valve With TCM and A/T Fluid Temperature Sensor 2"

 .

CAUTION:

Do not reuse drain plug gasket.

13. Pour ATF into A/T assembly. Refer to 

AT-12, "Changing A/T Fluid"

 .

AT-262

ON-VEHICLE SERVICE

Rear Oil Seal (VQ35DE Models Only)

NCS001QV

REMOVAL AND INSTALLATION
Removal

1.

Remove rear propeller shaft. Refer to 

PR-8, "Removal and

Installation"

 .

2.

Remove transfer assembly from A/T assembly (AWD models).
Refer to 

TF-44, "Removal and Installation"

 .

3.

Remove rear oil seal using a flat-bladed screwdriver.

CAUTION:

Be careful not to scratch rear extension assembly (2WD
models) or adapter case assembly (AWD models).

Installation

CAUTION:

After completing installation, check for A/T fluid leakage and A/T fluid level. Refer to 

AT-13, "Checking

A/T Fluid"

 .

1.

As shown in the figure, use the drift to drive rear oil seal into rear
extension assembly (2WD models) or adapter case assembly
(AWD models) until it is flush.

CAUTION:

●

Do not reuse rear oil seal.

●

Apply ATF to rear oil seal.

2.

Install transfer assembly to A/T assembly (AWD models). Refer
to 

TF-44, "Removal and Installation"

 .

3.

Install rear propeller shaft. Refer to 

PR-8, "Removal and Installa-

tion"

 .

SCIA5410E

SCIA5411E