Infiniti G37 Coupe. Manual - part 1200

SRC-50

< COMPONENT DIAGNOSIS >

B1052, B1057 DRIVER AIRBAG MODULE

B1052, B1057 DRIVER AIRBAG MODULE

Description

INFOID:0000000001694527

DTC B1052, B1057 [SHORT] DRIVER AIRBAG MODULE

For driver air bag module, crash is judged by main “G” sensor output signal and sub “G” sensor in front direc-
tion.

OPERATION

In case of frontal collision whose acceleration exceeds the specified level, the ignition materials are ignited by
electric ignition system. The system burns and introduces the chemical reaction of gas generating materials to
generate hot gases that flow into the air bag through a filter and expand the bag.

STRUCTURE

Driver air bag module mainly consists of air bag and inflator which inflates air bag.

INSTALLATION

Driver air bag module is installed on the center of steering wheel with fixed bolts.

DTC Logic

INFOID:0000000001694528

DTC DETECTION LOGIC

With CONSULT-lll

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

1.

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-lll.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-51, "Diagnosis Procedure (Component diagnosis)"

.

NO

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

1.

INSPECTION START

Turn ignition switch ON.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1052
B1057

DRIVER AIRBAG MOD-
ULE 
[SHORT]

Driver air bag module circuit are shorted 
to each other.
(including the spiral cable.)

• Disconnection of wiring harness

and short.

• Internal breakdown in driver air bag 

module.

• Internal breakdown in spiral cable.
• Internal breakdown in diagnosis sen-

sor unit (ACU).

B1052, B1057 DRIVER AIRBAG MODULE

SRC-51

< COMPONENT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

>> GO TO 2.

2.

CHECK AIR BAG WARNING LAMP

Check the warning lamp status.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-133, "DTC Index"

.

NO

>> INSPECTION END.

Diagnosis Procedure (Component diagnosis)

INFOID:0000000001694529

With CONSULT-lll

WARNING:

• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-

utes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device. 

DIAGNOSTIC PROCEDURE

1.

CHECK HARNESS CONNECTOR

Check the connection of harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace wiring harness.

3.

CHECK DRIVER AIR BAG MODULE

1.

Replace driver air bag module.

2.

Check the screen of CONSULT-III.

Is the inspection result normal?

YES

>> INSPECTION END.

NO

>> GO TO 4.

4.

CHECK SPIRAL CABLE CIRCUIT 

1.

Turn ignition switch OFF.

2.

Disconnect driver side air bag module harness connector and body side harness connector.

3.

Check continuity between driver side air bag module harness connector and body side harness connec-
tor.

4.

Check continuity between driver side air bag module harness connector and ground.

Driver side air bag module 

harness connector

Terminal

Body side harness 

connector

Terminal

Continuity 

M302

10

11

M35

28
30

Existed

M301

9

12

30
29

Driver side air bag module harness con-

nector

Terminal

Ground

Continuity 

M302

10

11

Not existed

M301

9

12

SRC-52

< COMPONENT DIAGNOSIS >

B1052, B1057 DRIVER AIRBAG MODULE

Is the inspection result normal?

YES

>> Check the intermittent incident. Refer to 

GI-38, "Intermittent Incident"

.

NO

>> Replace spiral cable.

B1058, B1059, B1060, B1061, B1062, B1063 DIAGNOSIS SENSOR UNIT

SRC-53

< COMPONENT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1058, B1059, B1060, B1061, B1062, B1063 DIAGNOSIS SENSOR UNIT

Description

INFOID:0000000001694530

DTC B1058, B1059, B1060, B1061, B1062, B1063 DIAGNOSIS SENSOR UNIT

Detects the whole SRS electrical system and displays the malfunction either by illuminating or blinking the air
bag warning lamp in the combination meter. Malfunctioning part can be detected by on board self-diagnosis
system and electro-diagnosis tester CONSULT-lll.

OPERATION

It detects a shock that exceeds specified level and monitors such systems as the driver and passenger air
bag, side air bag, curtain air bag, pre-tensioner seat belts and Occupant Classification System (OCS) operate
properly. 

STRUCTURE

It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.

INSTALLATION

SRS diagnosis sensor unit is installed under the center console with fixed bolts.

DTC Logic

INFOID:0000000001694531

DTC DETECTION LOGIC

With CONSULT-lll

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

1.

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-lll.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-54, "Diagnosis Procedure (Component diagnosis)"

.

NO

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

1.

INSPECTION START

Turn ignition switch ON.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1058
B1059
B1060
B1061
B1062
B1063

CONTROL UNIT 

Diagnosis sensor unit is out of order.

Internal breakdown in diagnosis sensor 
unit (ACU).