Infiniti G35 (V35) Sedan. Manual - part 428

DLN-146

< SYMPTOM DIAGNOSIS >

[REAR FINAL DRIVE: R200]

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

×

: Applicable

Reference

DLN-198, "

A

W

D : 

Inspe

c

ti

on

 Af

ter Di

sa

ssem

bl

y

"

DLN-194, "

AW

D

 :

 A

d

ju

s

tm

e

n

t"

DLN-198, "

A

W

D : 

Inspe

c

ti

on

 Af

ter Di

sa

ssem

bl

y

"

DLN-194, "

AW

D

 :

 A

d

ju

s

tm

e

n

t"

DLN-194, "

AW

D

 :

 A

d

ju

s

tm

e

n

t"

DLN-154, "

Inspe

c

tio

n

"

NVH in DLN 

section.

NVH in F

AX,

 RAX, FS

U and RSU sections.

NVH in WT 

section.

NVH in WT 

section.

NVH in F

AX and 

RAX

 section.

NVH in BR 

section.

NVH in ST 

section.

Possible cause and SUSPECTED PARTS

Ge

ar t

oot

h ro

ug

h

Ge

ar c

o

n

ta

c

t 

im

prop

er

T

o

ot

h s

u

rf

ac

es

 worn

Ba

ck

la

sh

 in

c

o

rre

ct

Co

mp

an

io

n fl

an

ge

 ex

c

e

s

s

iv

e

 run

o

u

t

Ge

ar o

il 

im

pro

p

e

r

PROPELLE

R

 SHAFT

AX

LE A

N

D 

SUSPENSION

TI

RE

S

ROAD WH

E

E

L

DRIVE

 SHAFT

BRAK

ES

ST

EERING

Symptom

Noise

×

×

×

×

×

×

×

×

×

×

×

×

×

PRECAUTIONS

DLN-147

< PRECAUTION >

[REAR FINAL DRIVE: R200]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

PRECAUTION

PRECAUTIONS

Service Notice or Precautions for Rear Final Drive

INFOID:0000000000957376

CAUTION:

• Check for the correct installation status prior to removal or disassembly. If matching marks are

required, be certain they do not interfere with the function of the parts when applied.

• Overhaul should be done in a clean work area, it is preferable to work in dustproof area.
• Before disassembly, using steam or white gasoline, completely remove sand and mud from the exte-

rior of the unit, preventing them from entering into the unit during disassembly or assembly.

• Check appearance of the disassembled parts for damage, deformation, and unusual wear. Replace

them with a new ones if necessary.

• Gaskets, seals and O-rings should be replaced any time when the unit is disassembled.
• In principle, tighten bolts or nuts gradually in several steps working diagonally from inside to out-

side. If tightening sequence is specified, observe it.

• Clean and flush the parts sufficiently and blow-dry them.
• Be careful not to damage sliding surfaces and mating surfaces.
• When applying sealant, remove the old sealant from the mounting surface; then remove any mois-

ture, oil, and foreign materials from the application and mounting surfaces.

• Always use shop paper for cleaning the inside of components.
• Avoid using cotton gloves or shop rags to prevent entering of lint.
• During assembly, observe the specified tightening torque, and apply new gear oil, petroleum jelly, or

multi-purpose grease as specified for each vehicle, if necessary.

DLN-148

< PREPARATION >

[REAR FINAL DRIVE: R200]

PREPARATION

PREPARATION

PREPARATION

Special Service Tools

INFOID:0000000000957377

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Tool number
(Kent-Moore No.)
Tool name

Description

KV40104100
(

—

)

Attachment

Removing side flange

ST36230000
(J-25840-A)
Sliding hammer 

Removing side flange

ST3127S000
(J-25765-A)
Preload gauge

Measuring pinion bearing preload and total 
preload

KV381054S0
(J-34286)
Puller

Removing front oil seal 

ST30720000
(J-25405)
Drift
a: 77 mm (3.03 in) dia.
b: 55.5 mm (2.185 in) dia.

• Installing front oil seal
• Installing pinion rear bearing outer race

KV38107900
(J-39352)
Protector

Installing side flange

ZZA0804D

ZZA0803D

ZZA0806D

ZZA0601D

ZZA0811D

S-NT129

PREPARATION

DLN-149

< PREPARATION >

[REAR FINAL DRIVE: R200]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

KV38100200
(J-26233)
Drift
a: 65 mm (2.56 in) dia.
b: 49 mm (1.93 in) dia.

Installing side oil seal

KV10111100
(J-37228)
Seal cutter

Removing rear cover

KV38100800
(J-25604-01)
Attachment
a: 541 mm (21.30 in)
b: 200 mm (7.87 in)

Fixing unit assembly

ST3306S001
(J-22888-D)
Differential side bearing puller set
1: ST33051001

(J-22888-20)
Puller

2: ST33061000

(J-8107-2)
Base
a: 28.5 mm (1.122 in) dia.
b: 38 mm (1.50 in) dia.

Removing and installing side bearing inner 
race

KV38100300
(J-25523)
Drift
a: 54 mm (2.13 in) dia.
b: 46 mm (1.81 in) dia.
c: 32 mm (1.26 in) dia.

Installing side bearing inner race

(J-8129)
Spring gauge

Measuring turning torque

Tool number
(Kent-Moore No.)
Tool name

Description

ZZA1143D

S-NT046

SDIA0267E

NT072

ZZA1046D

NT127