Infiniti G35 (V35) Sedan. Manual - part 403

DLN-46

< PREPARATION >

[TRANSFER: ETX13B]

PREPARATION

Commercial Service Tools

INFOID:0000000000957279

ST30611000
(J-25742-1)
Drift bar
a: 350 mm (13.78 in)
b: 25 mm (0.98 in) dia.
c: M12 

×

 1.5P

Removing rear bearing

ST35321000
(

—

)

Drift
a: 49 mm (1.93 in) dia.
b: 41 mm (1.61 in) dia.

• Removing rear bearing
• Installing mainshaft assembly

KV38104010
(

—

)

Drift
a: 67 mm (2.64 in) dia.
b: 49 mm (1.93 in) dia.

• Installing front drive shaft rear bearing
• Installing rear bearing

ST30621000
(J-25742-5)
Drift
a: 80 mm (3.15 in) dia.
b: 59 mm (2.32 in) dia.

Installing mainshaft bearing

ST31214000
(J-25269-B)
Drift
a: 34 mm (1.34 in) dia.
b: 25.5 mm (1.004 in) dia.

• Removing front drive shaft front bearing
• Removing front drive shaft rear bearing

ST33200000
(J-26082)
Drift
a: 60 mm (2.36 in) dia.
b: 44.5 mm (1.752 in) dia.

Installing front drive shaft front bearing

Tool number
(Kent-Moore No.)
Tool name

Description

NT663

ZZA1000D

ZZA1000D

ZZA1000D

ZZA0534D

ZZA1002D

PREPARATION

DLN-47

< PREPARATION >

[TRANSFER: ETX13B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

Tool name

Description

Puller

Removing companion flange

Flange wrench

Removing and installing self-lock nut

Puller

• Removing front drive shaft front bearing
• Removing front drive shaft rear bearing

Power tool

Loosening bolts and nuts

NT077

NT771

ZZB0823D

PBIC0190E

DLN-48

< ON-VEHICLE MAINTENANCE >

[TRANSFER: ETX13B]

TRANSFER FLUID

ON-VEHICLE MAINTENANCE

TRANSFER FLUID

Inspection

INFOID:0000000000957280

FLUID LEAKAGE

• Check if fluid is leaking from transfer or around it.

FLUID LEVEL

• Check fluid level from filler plug (1) mounting hole as shown in the

figure.

CAUTION:

Never start engine while checking fluid level.

• Before installing filler plug, set a new gasket. Install filler plug on

transfer and tighten to the specified torque. Refer to 

DLN-58,

"Exploded View"

.

CAUTION:

Never reuse gasket.

Draining

INFOID:0000000000957281

1.

Run the vehicle to warm up the transfer unit sufficiently.

2.

Stop the engine, and remove the drain plug (1) to drain the
transfer fluid.

CAUTION:

When draining fluid, protect exhaust tube flange with cover.

3.

Apply sealant to drain plug. Install drain plug on transfer and
tighten to the specified torque. Refer to 

DLN-58, "Exploded

View"

.

• Use Genuine Silicone RTV or equivalent. Refer to 

GI-15,

"Recommended Chemical Products and Sealants"

.

CAUTION:

Remove old sealant adhering to mounting surfaces. Also
remove any moisture, oil, or foreign material adhering to
application and mounting surfaces.

Refilling

INFOID:0000000000957282

1.

Remove filler plug (1) and add transfer fluid until fluid level
reaches the specified limit near filler plug mounting hole.

CAUTION:

Carefully fill the fluid. (Fill up for approx. 3 minutes.)

2.

Leave the vehicle for 3 minutes, and check the fluid level again.

3.

Set a new gasket onto filler plug and install it on transfer and
tighten to the specified torque. Refer to 

DLN-58, "Exploded

View"

.

CAUTION:

Never reuse gasket.

JSDIA0096ZZ

JSDIA0095ZZ

Fluid capacity

: Refer to 

DLN-76, "General 

Specifications"

.

JSDIA0096ZZ

AWD CONTROL UNIT

DLN-49

< ON-VEHICLE REPAIR >

[TRANSFER: ETX13B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

ON-VEHICLE REPAIR

AWD CONTROL UNIT

Exploded View

INFOID:0000000000957283

Removal and Installation

INFOID:0000000000957284

REMOVAL

1.

Remove the glove box assembly. Refer to 

IP-11, "Exploded View"

.

2.

Disconnect AWD control unit harness connector.

3.

Remove AWD control unit (1) mounting nuts.

4.

Remove AWD control unit.

INSTALLATION

Install is the reverse order of removal.

1.

AWD control unit

: Vehicle front

JSDIA0050ZZ

JSDIA0051ZZ