Infiniti G35 (V35) Sedan. Manual - part 275

CCS

INSPECTION AND ADJUSTMENT

CCS-11

< BASIC INSPECTION >

[INTELLIGENT CRUISE CONTROL]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

>> GO TO 2.

2.

LASER BEAM AIMING ADJUSTMENT

1.

After the CONSULT-III displays “ADJUST THE VERTICAL OF LASER BEAM AIMING” turn the up-down
direction adjusting screw until “U/D CORRECT” value is set in the range of 

±

4.

NOTE:
• Turn the screw slowly. The value change on display is slower than actual movement of the ICC sensor

integrated unit. Wait for 2 seconds every time the screw is turned half a rotation.

• Turning the screw (A) clockwise to laser beam is downward

(B) and counterclockwise to laser beam is upward (C).

>> GO TO 3.

3.

LASER BEAM AIMING CONFIRMATION

1.

When “U/D CORRECT” value indicates 

±

4, confirm that the margin of value remains within 

±

4 at least for

2 seconds with no equipment or hand touching the ICC sensor integrated unit. 

2.

When “COMPLETED THE VERTICAL AIMING OF LASER BEAM” appears on screen, touch “END”.
NOTE:
Be sure that the margin of “U/D CORRECT” is within 

±

4 with ICC sensor integrated unit is untouched.

3.

Confirm that “ADJUSTING AUTOMATIC HORIZONTAL LASER BEAM AIMING” is on screen and wait for
a while (maximum: 10 seconds).

4.

Confirm that “NORMALLY COMPLETED” is displayed on CONSULT-III and close the aiming adjustment
procedure by touching “END”.
NOTE:
Complete all the procedures once “LASER BEAM ADJUST” mode is entered in CONSULT-III. When the
procedure is discontinued, the ICC system is inoperable.

>> LASER BEAM AIMING ADJUSTMENT END

ACTION TEST

ACTION TEST : Description

INFOID:0000000000965386

Always perform the ICC system action test to check that the ICC system operates normally after replacing the
ICC sensor integrated unit or repairing any ICC system malfunction. 

ACTION TEST : Special Repair Requirement (Vehicle-To-Vehicle Distance Control 
Mode)

INFOID:0000000000965387

NOTE:
• When there is no vehicle ahead, drive at the set speed steadily.
• When there is a vehicle ahead, control to maintain distance from the vehicle ahead, watching its speed.

1.

CHECK FOR MAIN SWITCH

1.

Start engine.

JSOIA0018ZZ

CCS-12

< BASIC INSPECTION >

[INTELLIGENT CRUISE CONTROL]

INSPECTION AND ADJUSTMENT

2.

Press the MAIN switch (1) for less than 1.5 seconds.

3.

Check the ICC system display in the combination meter to check
that the vehicle-to-vehicle distance control mode is ready for
activation. 

4.

Press the MAIN switch, and check that the ICC system display turns off when the ICC system is deacti-
vated. 

5.

Check that the ICC system display turns off after starting the engine again. 

>> GO TO 2.

2.

CHECK FOR DISTANCE SWITCH

1.

Start engine.

2.

Press the MAIN switch for less than 1.5 seconds.

3.

Press the DISTANCE switch.

4.

Check if the set distance indicator changes display in order of: (Long)

→

(Middle)

→

(Short).

NOTE:
 The set distance indicator shows (Long) immediately after the engine starts.

>> GO TO 3.

3.

CHECK FOR RESUME/ACCELERATE, SET/COAST, CANCEL SWITCHES

1.

Check if RESUME/ACCELERATE, SET/COAST, CANCEL switches are operated smoothly.

2.

Check if switches come up as hand is released from the switches.

>> GO TO 4.

4.

SET CHECKING

1.

Start engine.

2.

Press the MAIN switch for less than 1.5 seconds.

3.

Drive the vehicle between 40 km/h (25 MPH) and 144 km/h (90 MPH).

4.

Push down the SET/COAST switch.

5.

Confirm that the desired speed is set as hand is released from the SET/COAST switch.

NOTE:

ICC system display status

“CRUISE” indicator lamp (2)

: ON

Set distance indicator (3)

: Long mode

Own vehicle indicator (4)

: ON

Set vehicle speed indicator (5)

: “— —”

JSOIA0004ZZ

JSOIA0005GB

CCS

INSPECTION AND ADJUSTMENT

CCS-13

< BASIC INSPECTION >

[INTELLIGENT CRUISE CONTROL]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

The set vehicle speed is displayed on the ICC system display.

>> GO TO 5.

5.

CHECK FOR INCREASE OF CRUISING SPEED

1.

Set vehicle-to-vehicle distance control mode at desired speed.

2.

Check if the set speed increases by 1 km/h (1 MPH) as RESUME/ACCELERATE switch is pushed up.

NOTE:
The maximum set speed of the vehicle-to-vehicle distance control mode is 144 km/h (90 MPH).

>> GO TO 6.

6.

CHECK FOR DECREASE OF CRUISING SPEED

1.

Set vehicle-to-vehicle distance control mode at desired speed.

2.

Check if the set speed decreases by 1 km/h (1 MPH) as SET/COAST switch is pushed down.

NOTE:
• Vehicle-to-vehicle distance control mode is automatically cancelled when the driving speed lowers to 32 km/

h (20 MPH) due to the deceleration of the vehicle ahead.

• The minimum set speed of the vehicle-to-vehicle distance control mode is 40 km/h (25 MPH).

>> GO TO 7.

7.

CHECK FOR CANCELLATION OF VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE

Check that the vehicle-to-vehicle distance control mode is canceled when performing the following operations. 
• When the brake pedal is depressed after the system is turned ON.
• When the clutch pedal is depressed after the system is turned ON (M/T).
• When the A/T selector lever is shifted to the “N” range (A/T).
• When the MAIN switch is turned OFF.
• When CANCEL switch is operated.

>> GO TO 8.

8.

CHECK FOR RESTORING SPEED THAT IS SET BY VEHICLE-TO-VEHICLE DISTANCE CONTROL

MODE BEFORE CANCELLATION

Check that the vehicle restores the previous speed kept before the system deactivation when performing the
following operations. 
• Cancel the system by depressing the brake pedal. Then check if the speed before cancellation is restored

when pushing up RESUME/ACCELERATE switch with 40 km/h (25 MPH) or above.

• Depress the clutch pedal to cancel the system. Then release the clutch pedal (shift knob at any of the 1st to

6th gear positions). Check that the vehicle restores the previous speed kept before the system deactivation
when pushing up the RESUME/ACCELERATE switch while the vehicle speed is 40 km/h (25 MPH) or more. 

• Shift the A/T shift selector lever to the “N” range to cancel the system. Then shift the A/T shift selector lever

back to the “D” range. Check that the vehicle restores the previous speed kept before the system deactiva-
tion when pushing up the RESUME/ACCELERATE switch while the vehicle speed is 40 km/h (25 MPH) or
more (A/T). 

• Press the CANCEL switch to cancel the system. Then check that the vehicle restores the previous speed

kept before the system deactivation when pushing up the RESUME/ACCELERATE switch while the vehicle
speed is 40 km/h (25 MPH) or more. 

>> OPERATION INSPECTION COMPLETION

ACTION TEST : Special Repair Requirement (Conventional (Fixed Speed) Cruise 
Control Mode)

INFOID:0000000000965388

1.

CHECK FOR MAIN SWITCH

1.

Start engine.

CCS-14

< BASIC INSPECTION >

[INTELLIGENT CRUISE CONTROL]

INSPECTION AND ADJUSTMENT

2.

Press the MAIN switch (1) for more than 1.5 seconds.

3.

Check that the ICC system display in the combination meter
indicates that the conventional (fixed speed) cruise control mode
is ready for activation. 

4.

Press the MAIN switch, and check that the ICC system display
turns off when the ICC system is deactivated. 

5.

Check that the ICC system display turns off after starting the
engine again. 

>> GO TO 2.

2.

CHECK FOR RESUME/ACCELERATE, SET/COAST, CANCEL SWITCHES

1.

Check if RESUME/ACCELERATE, SET/COAST, CANCEL switches are operated smoothly.

2.

Check if switches come up as hand is released from the switches.

>> GO TO 3.

3.

SET CHECKING

1.

Start engine.

2.

Press the MAIN switch for more than 1.5 seconds.

3.

Drive the vehicle between 40 km/h (25 MPH) and 144 km/h (90 MPH).

4.

Push down the SET/COAST switch.

5.

Confirm that the desired speed is set as hand is released from the SET/COAST switch.

NOTE:
• The set vehicle speed is not displayed on the ICC system display.
• The SET indicator in the ICC system display illuminates.

>> GO TO 4.

4.

CHECK FOR INCREASE OF CRUISING SPEED

1.

Set the conventional (fixed speed) cruise control mode at desired speed.

2.

Check if the set speed increases by 1.6 km/h (1 MPH) as RESUME/ACCELERATE switch is pushed up.

NOTE:
• If the RESUME/ACCELERATE switch is kept pushing up during cruise control driving, the vehicle speed

increases until the switch is released.

• The maximum set speed is 144 km/h (90 MPH).

>> GO TO 5.

5.

CHECK FOR DECREASE OF CRUISING SPEED

1.

Set the conventional (fixed speed) cruise control mode at desired speed.

2.

Check if the set speed decreases by 1.6 km/h (1 MPH) as SET/COAST switch is pushed down.

NOTE:
• Conventional (fixed speed) cruise control mode is automatically cancelled when the driving speed lowers to

32 km/h (20 MPH).

• The lowest set speed is 40 km/h (25 MPH).

>> GO TO 6.

6.

CHECK FOR CANCELLATION OF CONVENTIONAL (FIXED SPEED) CRUISE CONTROL MODE

Check that the CONVENTIONAL (FIXED SPEED) CRUISE CONTROL MODE is canceled when performing
the following operations. 
• When the brake pedal is depressed after the system is turned ON.
• When the clutch pedal is depressed after the system is turned ON (M/T).
• When the A/T selector lever is shifted to the “N” range (A/T).

ICC system display status

“CRUISE” indicator lamp (2)

: ON

JSOIA0006ZZ