Infiniti G35 (V35) Sedan. Manual - part 200

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-17

< FUNCTION DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

ACTIVE TEST

HEADLAMP

HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)

INFOID:0000000000963876

WORK SUPPORT

DOOR SW-DR
[ON/OFF]

The switch status input from front door switch (driver side)

DOOR SW-AS
[ON/OFF]

The switch status input from front door switch (passenger side)

DOOR SW-RR
[ON/OFF]

The switch status input from rear door switch RH

DOOR SW- RL
[ON/OFF]

The switch status input from rear door switch LH

DOOR SW-BK
[ON/OFF]

NOTE:
The item is indicated, but not monitored.

CDL LOCK SW
[ON/OFF]

Lock switch status received from central door lock switch by power window switch se-
rial link

CDL UNLOCK SW
[ON/OFF]

Unlock switch status received from central door lock switch by power window switch 
serial link

KEY CYL LK-SW
[ON/OFF]

Lock switch status received from key cylinder switch by power window switch serial 
link

KEY CYL UN-SW
[ON/OFF]

Unlock switch status received from key cylinder switch by power window switch serial 
link

TRNK/HAT MNTR
[ON/OFF]

The switch status input from trunk room lamp switch

RKE-LOCK
[ON/OFF]

Lock signal status received from remote keyless entry receiver

RKE-UNLOCK
[ON/OFF]

Unlock signal status received from remote keyless entry receiver

Monitor item

[Unit]

Description

Test item

Operation

Description

INT LAMP

ON

Outputs the interior room lamp control signal to turn map lamp and personal lamp ON 
(Map lamp switch is in DOOR position).

OFF

Stops the interior room lamp control signal to turn map lamp and personal lamp OFF.

STEP LAMP TEST

ON

Outputs the step lamp control signal to turn step lamp ON.

OFF

Stops the step lamp control signal to turn step lamp OFF.

LUGGAGE LAMP TEST

ON

Outputs the trunk room lamp control signal to turn step lamp ON.

OFF

Stops the trunk room lamp control signal to turn step lamp ON.

Service item

Setting item

Setting

BATTERY SAVER SET

ON*

With the exterior lamp battery saver function

OFF

Without the exterior lamp battery saver function

BCS-18

< FUNCTION DIAGNOSIS >

DIAGNOSIS SYSTEM (BCM)

*: Initial setting

DATA MONITOR

ILL DELAY SET

MODE 1*

45 sec.

Sets delay timer function timer operation time.
(All doors closed)

MODE 2

Without the func-
tion

MODE 3

30 sec.

MODE 4

60 sec.

MODE 5

90 sec.

MODE 6

120 sec.

MODE 7

150 sec.

MODE 8

180 sec.

CUSTOM A/LIGHT SET-
TING

MODE 1*

Normal

MODE 2

More sensitive setting than normal setting (Turns ON earlier than normal operation.)

MODE 3

More sensitive setting than MODE 2 (Turns ON earlier than MODE 2.)

MODE 4

Less sensitive setting than normal setting (Turns ON later than normal operation.)

Service item

Setting item

Setting

Monitor item

[Unit]

Description

PUSH SW
[ON/OFF]

The switch status input from push-button ignition switch

ENGINE STATE
[STOP/STALL/CRANK/RUN]

The engine status received from ECM with CAN communication

VEH SPEED 1
[km/h]

The value of the vehicle speed received from unified meter and A/C amp. with CAN 
communication

KEY SW-SLOT
[ON/OFF]

Key switch status input from key slot

TURN SIGNAL R
[ON/OFF]

Each switch status that BCM judges from the combination switch reading function

TURN SIGNAL L
[ON/OFF]

TAIL LAMP SW
[ON/OFF]

HI BEAM SW
[ON/OFF]

HEAD LAMP SW1
[ON/OFF]

HEAD LAMP SW2
[ON/OFF]

PASSING SW
[ON/OFF]

AUTO LIGHT SW
[ON/OFF]

FR FOG SW
[ON/OFF]

RR FOG SW
[ON/OFF]

NOTE:
The item is indicated, but not monitored.

DOOR SW-DR
[ON/OFF]

The switch status input from front door switch (driver side)

DOOR SW-AS
[ON/OFF]

The switch status input from front door switch (passenger side)

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-19

< FUNCTION DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

ACTIVE TEST

WIPER

WIPER : CONSULT - III Function (BCM - WIPER)

INFOID:0000000000963877

WORK SUPPORT

*:Factory setting

DATA MONITOR

DOOR SW-RR
[ON/OFF]

The switch status input from rear door switch RH

DOOR SW- RL
[ON/OFF]

The switch status input from rear door switch LH

DOOR SW-BK
[ON/OFF]

NOTE:
The item is indicated, but not monitored.

OPTICAL SENSOR
[V]

The value of exterior brightness voltage input from the optical sensor 

Monitor item

[Unit]

Description

Test item

Operation

Description

TAIL LAMP

ON

Transmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON.

OFF

Stops the tail lamp request signal transmission.

HEAD LAMP

HI

Transmits the high beam request signal with CAN communication to turn 
the headlamp (HI).

LO

Transmits the low beam request signal with CAN communication to turn 
the headlamp (LO).

OFF

Stops the high & low beam request signal transmission.

FR FOG LAMP

ON

Transmits the front fog lights request signal to IPDM E/R with CAN com-
munication to turn the front fog lamp ON.

OFF

Stops the front fog lights request signal transmission.

RR FOG LAMP

ON

NOTE:
The item is indicated, but cannot be tested.

OFF

DAYTIME RUNNING LIGHT

ON

NOTE:
The item is indicated, but cannot be tested.

OFF

CORNERING LAMP

RH

NOTE:
The item is indicated, but cannot be tested.

LH

OFF

ILL DIM SIGNAL

ON

NOTE:
The item is indicated, but cannot be tested.

OFF

Service item

Setting 

item

Description

WIPER SPEED 
SETTING

ON

With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)

OFF*

Without vehicle speed
(Front wiper intermittent time linked with the wiper intermittent dial position)

BCS-20

< FUNCTION DIAGNOSIS >

DIAGNOSIS SYSTEM (BCM)

ACTIVE TEST

FLASHER

FLASHER : CONSULT-III Function (BCM - FLASHER)

INFOID:0000000000963878

WORK SUPPORT

*: Initial setting

DATA MONITOR

Monitor Item

[Unit]

Description

PUSH SW

Displays the status of the engine switch (push switch) judged by BCM.

VEH SPEED 1
[km/h]

Displays the value of the vehicle speed signal received from unified meter and A/C 
amp. with CAN communication.

FR WIPER HI
[OFF/ON]

Status of each switch judged by BCM using the combination switch reading function

FR WIPER LOW
[OFF/ON]

FR WASHER SW
[OFF/ON]

FR WIPER INT
[OFF/ON]

FR WIPER STOP
[OFF/ON]

Displays the status of the front wiper auto stop signal received from IPDM E/R with 
CAN communication.

INT VOLUME
[1 

−

 7] 

Status of each switch judged by BCM using the combination switch reading function

Test item

Operation

Description

FRONT WIPER

HI

Transmits the front wiper request signal (HI) to IPDM E/R with CAN communication to op-
erate the front wiper HI operation.

LO

Transmits the front wiper request signal (LO) to IPDM E/R with CAN communication to 
operate the front wiper LO operation.

INT

Transmits the front wiper request signal (INT) to IPDM E/R with CAN communication to 
operate the front wiper INT operation.

OFF

Stops transmitting the front wiper request signal to stop the front wiper operation.

Service item

Setting item

Setting

HAZARD ANSWER 
BACK

LOCK ONLY*

With locking only

Sets the hazard warning lamp answer back function 
when the door is lock/unlock with the request switch or 
the key fob.

UNLK ONLY

With unlocking only

LOCK/UNLK

With locking/unlocking

OFF

Without the function

Monitor item

[Unit]

Description

REQ SW-DR
[ON/OFF]

The switch status input from the request switch (driver side)

REQ SW-AS
[ON/OFF]

The switch status input from the request switch (passenger side)

PUSH SW
[ON/OFF]

The switch status input from the push-button ignition switch