Infiniti G35 (V35) Sedan. Manual - part 1301

 

  Index      Infiniti     Infiniti G35 (V35) Sedan - service repair manual 2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1299  1300  1301  1302   ..

 

 

Infiniti G35 (V35) Sedan. Manual - part 1301

 

 

STC-94

< COMPONENT DIAGNOSIS >

[WITH 4WAS]

C1909 4WAS MAIN CONTROL UNIT

C1909 4WAS MAIN CONTROL UNIT

Description

INFOID:0000000000958839

• 4WAS rear actuator and the power steering solenoid valve is controlled by each sensor signal.
• The fail-safe functions stops the rear wheel angle (the front wheel is the steering wheel cutting angle) when

the electric components and the mechanical components are malfunctioning.

• The protection function mode stops 4WAS system intermittently when the input signal does not input to

4WAS main control unit.

• 4WAS front control unit and 4WAS main control unit control the best control of 4WAS system by 4WAS com-

munication line.

DTC Logic

INFOID:0000000000958840

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

RECHECK DTC

 With CONSULT-III

1.

Turn the ignition switch OFF to ON.

2.

Perform 4WAS main control unit self-diagnosis.

Is DTC “C1909” detected?

YES

>> Proceed to diagnosis procedure. Refer to 

STC-94, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000000958841

1.

CHECK 4WAS MAIN CONTROL UNIT POWER SUPPLY

1.

Turn the ignition switch OFF.

2.

Disconnect 4WAS main control unit harness connector.

3.

Check the voltage between 4WAS main control unit harness connector terminal and the ground.

4.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

5.

Check the voltage between 4WAS main control unit harness connector terminal and the ground.

Is the inspection result normal?

YES

>> GO TO 2.

NG

>>

Check the following items. Repair or replace the malfunctioning parts.

• 10A fuse (#45) open
- Short among 10A fuse (#45) connector, 4WAS main control unit harness connector No. 27 ter-

minal and the ground

DTC

Items

(CONSULT-III screen terms)

Diagnostic item is detected when...

Possible cause

C1909

CONTROL UNIT
[ABNORMAL6]

An error is detected inside 4WAS main control unit.

4WAS main control unit

4WAS main control unit

Voltage (Approx.)

Connector

Terminal

B54

27 – Ground

0 V

4WAS main control unit

Voltage (Approx.)

Connector

Terminal

B54

27 – Ground

Battery voltage

C1909 4WAS MAIN CONTROL UNIT

STC-95

< COMPONENT DIAGNOSIS >

[WITH 4WAS]

C

D

E

F

H

I

J

K

L

M

A

B

STC

N

O

P

• Open between the ignition switch and 4WAS main control unit harness connector No. 27 termi-

nal

• Ignition switch

2.

CHECK 4WAS MAIN CONTROL UNIT GROUND

Check the continuity between 4WAS main control unit harness connector and the ground.

Is the inspection result normal?

YES

>> GO TO 3.

NG

>> Repair or replace the harnesses and connectors.

3.

PERFORM SELF-DIAGNOSIS (4WAS MAIN CONTROL UNIT)

 With CONSULT-III

1.

Connect 4WAS main control unit harness connector.

2.

Perform 4WAS main control unit self-diagnosis.

Is DTC “C1909” detected?

YES

>> Replace 4WAS main control unit. Refer to 

STC-178, "Exploded View"

.

NO

>> GO TO 4.

4.

CHECK INFORMAION

 With CONSULT-III

Check the “DATA MONITOR” value of each DTC detected with the self-diagnosis function. Refer to 

STC-155,

"Reference Value"

.

Is each data the standard value?

YES

>> Check each harness connector pin terminal for disconnection.

NO

>> Replace 4WAS main control unit. Refer to 

STC-178, "Exploded View"

.

Special Repair Requirement

INFOID:0000000000958842

BEFORE REPLACING 4WAS MAIN CONTROL UNIT

• Record the self-diagnosis results (history).

CAUTION:

• Replace it without erasing the memory (history) of self-diagnosis results when replacing 4WAS

main control unit after diagnosis.

• Erase the memory of the self-diagnosis results (record) after printing out or recording all the val-

ues of “DATA MONITOR” when erasing the memory of the self-diagnosis results (record).

4WAS main control unit

Continuity

Connector

Terminal

M204

34 – Ground

Existed

STC-96

< COMPONENT DIAGNOSIS >

[WITH 4WAS]

C1911, C1912 4WAS REAR MOTOR POWER SUPPLY

C1911, C1912 4WAS REAR MOTOR POWER SUPPLY

Description

INFOID:0000000000958843

• The power supply for 4WAS rear motor.

DTC Logic

INFOID:0000000000958844

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

RECHECK DTC

1.

Turn the ignition switch OFF to ON.

CAUTION:

Stop the vehicle. Wait 15 minutes or more.

2.

Perform 4WAS main control unit self-diagnosis.

Is DTC “C1911” or “C1912” detected?

YES

>> Proceed to diagnosis procedure. Refer to 

STC-96, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000000958845

1.

CHECK 4WAS MAIN CONTROL UNIT POWER SUPPLY

1.

Turn the ignition switch OFF.

2.

Disconnect 4WAS main control unit harness connector.

3.

Check the voltage between 4WAS main control unit harness connectors and the ground.

4.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

5.

Check the voltage between 4WAS main control unit harness connectors and the ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>>

Check the following items. Repair or replace the malfunctioning parts.

• 10A fuse (#45) open
- Short among 10A fuse (#45) connector, 4WAS main control unit harness connector No. 27 ter-

minal and the ground

• Open between the ignition switch and 4WAS main control unit harness connector No. 27 termi-

nal

DTC

Items

(CONSULT-III screen terms)

Diagnostic item is detected when...

Possible cause

C1911

MOTOR VOLTAGE
[LOW VOLTAGE]

4WAS rear motor voltage error is detected.
(4WAS rear motor voltage is low.)

4WAS rear motor power 
supply error

C1912

MOTOR VOLTAGE
[BAD OBSTRCT]

4WAS rear motor voltage error is detected.
(Voltage is applied to 4WAS main motor when 4WAS 
main control unit output is “OFF”.)

4WAS rear motor power 
supply error

4WAS main control unit

Voltage (Approx.)

Connector

Terminal

B54

27 – Ground

0 V

4WAS main control unit

Voltage (Approx.)

Connector

Terminal

B54

27 – Ground

Battery voltage

C1911, C1912 4WAS REAR MOTOR POWER SUPPLY

STC-97

< COMPONENT DIAGNOSIS >

[WITH 4WAS]

C

D

E

F

H

I

J

K

L

M

A

B

STC

N

O

P

• Ignition switch

2.

CHECK 4WAS REAR MOTOR POWER SUPPLY CIRCUIT (1)

1.

Turn the ignition switch OFF.

2.

Remove 4WAS rear motor relay.

3.

Check the continuity between 4WAS rear motor relay harness connector terminal and the ground.

4.

Check the continuity between 4WAS rear motor relay harness connector terminal and 4WAS main control
unit harness connector terminal.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the harnesses and connectors.

3.

CHECK 4WAS REAR MOTOR POWER SUPPLY CIRCUIT (2)

Check the voltage between 4WAS rear motor relay harness connector terminal and the ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>>

Check the following items. Repair or replace the malfunctioning parts.

• 20A fuse (#37) open
- Short among 20A fuse (#37) connector, 4WAS rear motor relay harness connector No. 3 termi-

nal and the ground

• Open between the battery and 4WAS rear motor relay harness connector No. 3 terminal

4.

CHECK 4WAS REAR MOTOR POWER SUPPLY CIRCUIT (3)

1.

Remove the noise suppressor.

2.

Check continuity between the noise suppressor harness connector terminal and the ground.

3.

Check the continuity between the noise suppressor harness connector terminal and 4WAS rear motor
relay harness connector terminal.

4WAS rear motor relay

Continuity

Connector

Terminal

B53

1 – Ground

Existed

2 – Ground

Not existed

4WAS rear motor relay

4WAS main control unit

Continuity

Connector

Terminal

Connector

Terminal

B53

2

B54

25

Existed

4WAS rear motor relay

Voltage (Approx.)

Connector

Terminal

B53

3 – Ground

Battery voltage

Noise suppressor

Continuity

Connector

Terminal

B51

3 – Ground

Not existed

5 – Ground

B52

1 – Ground

Not existed

2 – Ground

Existed

Noise suppressor

4WAS rear motor relay

Continuity

Connector

Terminal

Connector

Terminal

B52

1

B53

5

Existed

 

 

 

 

 

 

 

Content   ..  1299  1300  1301  1302   ..