Infiniti G35 (V35) Sedan. Manual - part 1070

PWC-112

< SYMPTOM DIAGNOSIS >

[FRONT & REAR WINDOW ANTI-PINCH]

ANTI-PINCH SYSTEM DOES NOT OPERATE NORMALLY (DRIVER SIDE)

ANTI-PINCH SYSTEM DOES NOT OPERATE NORMALLY (DRIVER SIDE)

Diagnosis Procedure

INFOID:0000000000961632

1.

PERFORM INITIALIZATION PROCEDURE

Perform initialization procedure. 
Refer to 

PWC-7, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special

Repair Requirement"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK DOOR WINDOW SLIDING PART 

• A foreign material adheres to window glass or glass run rubber.
• Glass run rubber wear or deformation.
• Sash is tilted too much or not enough.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CHECK ENCODER CIRCUIT

Check encoder circuit.
Refer to 

PWC-29, "DRIVER SIDE : Component Function Check"

.

Is the inspection result normal?

YES

>> Inspection end.

NO

>> Check intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.

ANTI-PINCH SYSTEM DOES NOT OPERATE NORMALLY (PASSENGER SIDE)

PWC-113

< SYMPTOM DIAGNOSIS >

[FRONT & REAR WINDOW ANTI-PINCH]

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

ANTI-PINCH SYSTEM DOES NOT OPERATE NORMALLY (PASSENGER
SIDE)

Diagnosis Procedure

INFOID:0000000000961633

1.

PERFORM INITIALIZATION PROCEDURE

Perform initialization procedure. 
Refer to 

PWC-7, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special

Repair Requirement"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK DOOR WINDOW SLIDING PART 

• A foreign material adheres to window glass or glass run rubber.
• Glass run rubber wear or deformation.
• Sash is tilted too much or not enough.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CHECK ENCODER CIRCUIT

Check encoder circuit.
Refer to 

PWC-31, "PASSENGER SIDE : Component Function Check"

.

Is the inspection result normal?

YES

>> Inspection end.

NO

>> Check intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.

PWC-114

< SYMPTOM DIAGNOSIS >

[FRONT & REAR WINDOW ANTI-PINCH]

ANTI-PINCH SYSTEM DOES NOT OPERATE NORMALLY (REAR LH SIDE)

ANTI-PINCH SYSTEM DOES NOT OPERATE NORMALLY (REAR LH SIDE)

Diagnosis Procedure

INFOID:0000000000961634

1.

PERFORM INITIALIZATION PROCEDURE

Perform initialization procedure. 
Refer to 

PWC-7, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special

Repair Requirement"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK DOOR WINDOW SLIDING PART 

• A foreign material adheres to window glass or glass run rubber.
• Glass run rubber wear or deformation.
• Sash is tilted too much or not enough.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CHECK ENCODER CIRCUIT

Check encoder circuit.
Refer to 

PWC-33, "REAR LH : Component Function Check"

.

Is the inspection result normal?

YES

>> Inspection end.

NO

>> Check intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.

ANTI-PINCH SYSTEM DOES NOT OPERATE NORMALLY (REAR RH SIDE)

PWC-115

< SYMPTOM DIAGNOSIS >

[FRONT & REAR WINDOW ANTI-PINCH]

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

ANTI-PINCH SYSTEM DOES NOT OPERATE NORMALLY (REAR RH SIDE)

Diagnosis Procedure

INFOID:0000000000961635

1.

PERFORM INITIALIZATION PROCEDURE

Perform initialization procedure.
Refer to 

PWC-7, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special

Repair Requirement"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK DOOR WINDOW SLIDING PART 

• A foreign material adheres to window glass or glass run rubber.
• Glass run rubber wear or deformation.
• Sash is tilted too much or not enough.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CHECK ENCODER CIRCUIT

Check encoder circuit.
Refer to 

PWC-35, "REAR RH : Component Function Check"

.

Is the inspection result normal?

YES

>> Inspection end.

NO

>> Check intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.