Infiniti G35 (V35) Sedan. Manual - part 30

 

  Index      Infiniti     Infiniti G35 (V35) Sedan - service repair manual 2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  28  29  30  31   ..

 

 

Infiniti G35 (V35) Sedan. Manual - part 30

 

 

ADP-114

< COMPONENT DIAGNOSIS >

TELESCOPIC SENSOR

TELESCOPIC SENSOR

Description

INFOID:0000000000960720

• The telescopic sensor is installed to the steering column assembly. 
• The resistance of telescopic sensor is changed according to the forward/backward position of steering col-

umn. 

• The terminal voltage of automatic drive positioner control unit will be changed according to a change of tele-

scopic sensor resistance. Automatic drive positioner control unit calculates the telescopic position from the
voltage.

Component Function Check

INFOID:0000000000960721

1.

CHECK FUNCTION

1.

Select “TELESCO SEN” in “Data monitor” mode with CONSULT-III.

2.

Check the tilt sensor signal under the following conditions.

Is the indication normal?

YES

>> INSPECTION END.

NO

>> Perform diagnosis procedure. Refer to 

ADP-114, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000000960722

1.

CHECK TELESCOPIC SENSOR SIGNAL

1.

Turn ignition switch ON.

2.

Check voltage automatic drive positioner control unit harness connector and ground. 

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> GO TO 2.

2.

CHECK TELESCOPIC SENSOR CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect automatic drive positioner control unit and tilt & telescopic sensor connector.

3.

Check continuity between automatic drive positioner control unit harness connector and tilt & telescopic
sensor harness connector.

4.

Check continuity between automatic drive positioner control unit harness connector and ground.

Is the inspection result normal?

Monitor item

Condition

Value

TELESCO SEN

Telescopic position

Rear

0.8 [V]

Front

3.4 [V]

Terminal

Condition

Voltage (V)

(Approx.)

(+)

(-)

Tilt & telescopic 

sensor connector

Terminal

M48

2

Ground

Telescopic position

Rear

0.8 [V]

Front

3.4 [V]

Automatic drive positioner

control unit connector

Terminal

Tilt & telescopic sensor

connector

Terminal

Continuity

M51

23

M48

2

Existed

Automatic drive positioner

control unit connector

Terminal

Ground

Continuity 

M51

23

Not existed

TELESCOPIC SENSOR

ADP-115

< COMPONENT DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK TELESCOPIC SENSOR POWER SUPPLY

1.

Connect automatic drive positioner control unit connector.

2.

Turn ignition switch ON.

3.

Check voltage between tilt & telescopic sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 4.

4.

CHECK TELESCOPIC SENSOR POWER SUPPLY CIRCUIT 

1.

Turn ignition switch OFF.

2.

Disconnect automatic drive positioner control unit connector.

3.

Check continuity between automatic drive positioner control unit harness connector and tilt & telescopic
sensor harness connector.

4.

Check continuity between automatic drive positioner control unit harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness.

5.

CHECK TELESCOPIC SENSOR GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect automatic drive positioner control unit connector.

3.

Check continuity between automatic drive positioner control unit harness connector and tilt & telescopic
sensor harness connector.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness.

6.

CHECK DOOR MIRROR OPERATION

1.

Connect automatic drive positioner control unit connector and tilt & telescopic sensor connector.

2.

Turn ignition switch ON.

3.

Check door mirror operation with memory function.

Is the operation normal?

YES

>> Replace telescopic sensor. (Built in steering column assembly.)

NO

>> Repair or replace harness.

7.

CHECK INTERMITTENT INCIDENT

Terminal

Voltage (V)

(Approx.)

(+)

(–)

Tilt & telescopic sensor

Terminal

M48

2

Ground

5

Automatic drive positioner

control unit connector

Terminal

Tilt & telescopic sensor

connector

Terminal

Continuity

M52

33

M48

1

Existed

Automatic drive positioner

control unit connector

Terminal

Ground

Continuity 

M52

33

Not existed

Automatic drive positioner

control unit connector

Terminal

Tilt & telescopic sensor

connector

Terminal

Continuity

M52

41

M48

4

Existed

ADP-116

< COMPONENT DIAGNOSIS >

TELESCOPIC SENSOR

Refer to 

GI-39, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> Replace automatic drive positioner control unit.

NO

>> Repair or replace the malfunctioning part.

MIRROR SENSOR

ADP-117

< COMPONENT DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

MIRROR SENSOR

DRIVER SIDE

DRIVER SIDE : Description

INFOID:0000000000960723

• The mirror sensor (driver side) is installed to the door mirror (driver side).
• The resistance of 2 sensors (horizontal and vertical) is changed when the door mirror (driver side) is oper-

ated.

• Automatic drive positioner control unit calculates the door mirror position according to the change of the volt-

age of 2 sensor input terminals.

DRIVER SIDE : Component Function Check

INFOID:0000000000960724

1.

CHECK FUNCTION

1.

Select “MIR/SEN LH U-D”, “MIR/SEN LH R-L” in “Data monitor” with CONSULT-III.

2.

Check mirror sensor (driver side) signal under the following condition.

Is the indication normal?

YES

>> INSPECTION END

NO

>> Perform diagnosis procedure. Refer to 

ADP-117, "DRIVER SIDE : Diagnosis Procedure"

.

DRIVER SIDE : Diagnosis Procedure

INFOID:0000000000960725

1.

CHECK DOOR MIRROR (DRIVER SIDE) SENSOR SIGNAL

1.

Turn ignition switch ON.

2.

Check voltage between door mirror (driver side) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> GO TO 2.

2.

CHECK DOOR MIRROR (DRIVER SIDE) SENSOR CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect automatic drive positioner control unit and door mirror (driver side) connector.

3.

Check continuity between automatic drive positioner control unit harness connector and door mirror
(driver side) harness connector.

Monitor item

Condition

Value

MIR/SEN LH U-D

Door mirror (driver side)

Close to peak

3.4 [V]

Close to valley

0.6 [V]

MIR/SEN LH R-L

Close to right edge

3.4 [V]

Close to left edge

0.6 [V]

Terminals

Condition

Voltage (V)

(Approx.)

(+)

(–)

Door mirror (driver 

side) connector

Terminal

D3

9

Ground

Door mirror
(Driver side)

Close to peak

3.4

Close to valley

0.6

10

Close to right edge

3.4

Close to left edge

0.6

Automatic drive positioner

 control unit connector

Terminal

Door mirror (driver side)

connector

Terminal

Continuity

M51

6

D3

9

Existed

22

10

 

 

 

 

 

 

 

Content   ..  28  29  30  31   ..