Infiniti G35 (V35) Sedan. Manual - part 3

ADP-6

< BASIC INSPECTION >

DIAGNOSIS AND REPAIR WORKFLOW

1.

GET INFORMATION FOR SYMPTOM

Get the detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurred).

>> GO TO 2.

2.

CHECK DTC WITH AUTOMATIC DRIVE POSITIONER SYSTEM

Check “Self Diagnostic Result” with CONSULT-III.

Is any symptom described and any DTC is displayed? 

ADP-156, "DTC Index"

.

Symptom is described, DTC is displayed.>>GO TO 3.
Symptom is not described, DTC is displayed.>>GO TO 7.
Symptom is described, DTC is not displayed.>>GO TO 4.

3.

CONFIRM THE SYMPTOM

Try to confirm the symptom described by the customer.

>> GO TO 7.

4.

CONFIRM THE SYMPTOM

Try to confirm the symptom described by the customer.

>> GO TO 5.

5.

CHECK NORMAL OPERATING CONDITION

Check normal operating condition. Refer to 

ADP-213, "Description"

.

Is the incident normal operation?

YES

>> INSPECTION END

NO

>> GO TO 6.

6.

PERFORM BASIC INSPECTION

Isolate the malfunctioning point with the basic inspection. Refer to .

>> GO TO 8.

7.

PERFORM DTC CONFIRMATION PROCEDURE

Perform the confirmation procedure for the detected DTC.

Is the DTC displayed?

YES

>> GO TO 9.

NO

>> Check intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.

8.

PERFORM COMPONENT FUNCTION CHECK 

Perform the component function check for the isolated malfunctioning point.

>> GO TO 9.

9.

DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE

Isolate the malfunctioning point by performing the diagnosis procedure relevant to the symptom during the
component diagnosis.

>> GO TO 10.

10.

REPARE OR REPLACE

Repair or replace the malfunctioning part.

>> GO TO 11.

DIAGNOSIS AND REPAIR WORKFLOW

ADP-7

< BASIC INSPECTION >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

11.

FINAL CHECK

Perform the DTC confirmation procedure (if DTC is detected) or component function check (if no DTC is
detected) again, and then check that the malfunction can be repaired securely.

Are symptom and DTC not detected?

YES

>> INSPECTION END

Symptom is detected.>> GO TO 4.
DTC is detected.>> GO TO 7.

ADP-8

< BASIC INSPECTION >

INSPECTION AND ADJUSTMENT

INSPECTION AND ADJUSTMENT

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : De-
scription

INFOID:0000000000960577

Each function is reset to the following condition when the battery terminal is disconnected.

*1

: This function only for AT model.

*2

: Default value is 40mm.

NOTE:
Notice that disconnecting the battery when detected DTC are present will erase the DTC memory.

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Spe-
cial Repair Requirement

INFOID:0000000000960578

1.

SYSTEM INITIALIZATION

Perform system initialization. Refer to 

ADP-9, "SYSTEM INITIALIZATION : Description"

.

>> GO TO 2.

2.

SYSTEM SETTING

Perform system setting. Refer to 

ADP-11, "SYSTEM SETTING : Description"

.

>> GO TO 3.

3.

MEMORY STORAGE

Perform memory storage. Refer to 

ADP-10, "MEMORY STORING : Description"

.

>> END

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description

INFOID:0000000000960579

Each function is reset to the following condition when the driver seat control unit is replaced.

*1

: This function only for AT model.

Function

Condition

Procedure

Memory (Seat, steering, mirror)

Erased

Perform storing

Entry/exit assist

*1

OFF

Perform initialization

Set slide amount

*2

Intelligent Key interlock

Erased

Perform initialization

Perform storing

Seat synchronization

OFF

—

Function

Condition

Procedure

Memory (Seat, steering, mirror)

Erased

Perform storing

Entry/exit assist

*1

OFF

Perform initialization

Set slide amount

*2

Intelligent Key interlock

Erased

Perform initialization

Perform storing

Seat synchronization

OFF

—

INSPECTION AND ADJUSTMENT

ADP-9

< BASIC INSPECTION >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

*2

: Default value is 40mm.

NOTE:
Notice that disconnecting the battery when detected DTC are present will erase the DTC memory.

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement

INFOID:0000000000960580

1.

SYSTEM INITIALIZATION

Perform system initialization. Refer to 

ADP-9, "SYSTEM INITIALIZATION : Description"

.

>> GO TO 2.

2.

SYSTEM SETTING

Perform system setting. Refer to 

ADP-11, "SYSTEM SETTING : Description"

.

>> GO TO 3.

3.

MEMORY STORAGE

Perform memory storage. Refer to 

ADP-10, "MEMORY STORING : Description"

.

>> END

SYSTEM INITIALIZATION

SYSTEM INITIALIZATION : Description

INFOID:0000000000960581

Always perform the initialization when the battery terminal is disconnected or the driver seat control unit is
replaced.
The entry/exit assist function and Intelligent Key interlock function will not operate normally if no initialization is
performed. 

SYSTEM INITIALIZATION : Special Repair Requirement

INFOID:0000000000960582

INITIALIZATION PROCEDURE

1.

 CHOOSE METHOD

There are two initialization methods.
Which method do you use?

With door switch>>GO TO 2.
With vehicle speed>>GO TO 4.

2.

 STEP A-1

Turn ignition switch from ACC to OFF position. 

>> GO TO 2.

3.

 STEP A-2

Driver door switch is ON (open) 

→

 OFF (close) 

→

 ON (open).

>> END

4.

 STEP B-1

Drive the vehicle at more than 25 km/h (16 MPH). 

>> END

MEMORY STORING