Infiniti G20 (P11). Manual - part 282

 

  Index      Infiniti     Infiniti G20 (P11) - service repair manual 1999-2002 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  280  281  282  283   ..

 

 

Infiniti G20 (P11). Manual - part 282

 

 

5)

Set voltmeter probes to ECM terminals 84 (EVAP control sys-
tem pressure sensor signal) and ground.

6)

Check EVAP control system pressure sensor value at idle
speed and note it.

7)

Establish and maintain the following conditions for at least 1
minute.

Air conditioner switch

ON

Steering wheel

Fully turned

Headlamp switch

ON

Rear window defogger switch

ON

Engine speed

Approx. 3,000 rpm

Gear position

Any position other than “P”, “N” or “R”

8)

Verify that EVAP control system pressure sensor value stays
0.1V less than the value at idle speed (measured at step 6) for
at least 1 second.

9)

If NG, go to “Diagnostic Procedure”, EC-540.

GI

MA

EM

LC

FE

CL

MT

AT

AX

SU

BR

ST

RS

BT

HA

SC

EL

IDX

DTC P1447 EVAPORATIVE EMISSION (EVAP) CONTROL SYSTEM PURGE

FLOW MONITORING

Overall Function Check (Cont’d)

EC-539

Diagnostic Procedure

=NCEC0608

1

CHECK EVAP CANISTER

1. Turn ignition switch “OFF”.
2. Check EVAP canister for cracks.

OK or NG

OK (With CONSULT-II)

©

GO TO 2.

OK (Without CONSULT-
II)

©

GO TO 3.

NG

©

Replace EVAP canister.

2

CHECK PURGE FLOW

With CONSULT-II

1. Disconnect vacuum hose connected to EVAP canister purge volume control solenoid valve at EVAP service port and

install vacuum gauge.

SEF850X

2. Start engine and let it idle.
3. Select “PURG VOL CONT/V” in “ACTIVE TEST” mode with CONSULT-II.
4. Rev engine up to 2,000 rpm.
5. Touch “Qd” and “Qu” on CONSULT-II screen to adjust “PURG VOL CONT/V” opening and check vacuum existence.

SEF804Y

OK or NG

OK

©

GO TO 7.

NG

©

GO TO 4.

DTC P1447 EVAPORATIVE EMISSION (EVAP) CONTROL SYSTEM PURGE

FLOW MONITORING

Diagnostic Procedure

EC-540

3

CHECK PURGE FLOW

Without CONSULT-II

1. Start engine and warm it up to normal operating temperature.
2. Stop engine.
3. Disconnect vacuum hose connected to EVAP canister purge volume control solenoid valve at EVAP service port and

install vacuum gauge.

SEF850X

4. Start engine and let it idle for at least 80 seconds.
5. Check vacuum gauge indication when revving engine up to 2,000 rpm.

Vacuum should exist.

6. Release the accelerator pedal fully and let idle.

Vacuum should not exist.

OK or NG

OK

©

GO TO 7.

NG

©

GO TO 4.

4

CHECK EVAP PURGE LINE

1. Turn ignition switch “OFF”.
2. Check EVAP purge line for improper connection or disconnection.

Refer to “EVAPORATIVE EMISSION LINE DRAWING”, EC-37.

OK or NG

OK

©

GO TO 5.

NG

©

Repair it.

GI

MA

EM

LC

FE

CL

MT

AT

AX

SU

BR

ST

RS

BT

HA

SC

EL

IDX

DTC P1447 EVAPORATIVE EMISSION (EVAP) CONTROL SYSTEM PURGE

FLOW MONITORING

Diagnostic Procedure (Cont’d)

EC-541

5

CHECK EVAP PURGE HOSE AND PURGE PORT

1. Disconnect purge hoses connected to EVAP service port and EVAP canister purge volume control solenoid valve B.

SEF367U

2. Blow air into each hose and EVAP purge port C.
3. Check that air flows freely.

SEF368U

OK or NG

OK (With CONSULT-II)

©

GO TO 6.

OK (Without CONSULT-
II)

©

GO TO 7.

NG

©

Repair or clean hoses and/or purge port.

6

CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE

With CONSULT-II

1. Start engine.
2. Perform “PURG VOL CONT/V” in “ACTIVE TEST” mode with CONSULT-II. Check that engine speed varies according

to the valve opening.

SEF801Y

OK or NG

OK

©

GO TO 8.

NG

©

GO TO 7.

DTC P1447 EVAPORATIVE EMISSION (EVAP) CONTROL SYSTEM PURGE

FLOW MONITORING

Diagnostic Procedure (Cont’d)

EC-542

 

 

 

 

 

 

 

Content   ..  280  281  282  283   ..