Infiniti FX35 / FX45. Manual - part 609

SERVICE DATA AND SPECIFICATIONS (SDS)

EC-1197

< SERVICE INFORMATION >

[VK45DE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

Crankshaft Position Sensor (POS)

INFOID:0000000001327096

Refer to 

EC-910, "Component Inspection"

.

Camshaft Position Sensor (PHASE)

INFOID:0000000001327097

Refer to 

EC-915, "Component Inspection"

.

A/F Sensor 1 Heater

INFOID:0000000001327098

Heated Oxygen sensor 2 Heater

INFOID:0000000001327099

Throttle Control Motor

INFOID:0000000001327100

Fuel Injector

INFOID:0000000001327101

Fuel Pump

INFOID:0000000001327102

Resistance [at 25

°

C (77

°

F)]

2.3 - 4.3

Ω

Resistance [at 25

°

C (77

°

F)]

5.0 - 7.0

Ω

Resistance [at 25

°

C (77

°

F)]

Approximately 1 - 15

Ω

Resistance [at 10 - 60

°

C (50 - 140

°

F)]

13.5 - 17.5

Ω

Resistance [at 25

°

C (77

°

F)]

0.2 - 5.0

Ω

EI-1

BODY

C

D

E

F

G

H

J

K

L

M

SECTION 

EI

A

B

EI

N

O

P

CONTENTS

EXTERIOR & INTERIOR

SERVICE INFORMATION  ............................

3

PRECAUTIONS ...................................................

3

Precaution for Supplemental Restraint System 
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...................................................................

3

Precaution for Procedure without Cowl Top Cover 

......

3

Precaution for Work  ..................................................

3

PREPARATION ...................................................

4

Special Service Tool  .................................................

4

Commercial Service Tool  ..........................................

4

SQUEAK AND RATTLE TROUBLE DIAG-
NOSES ................................................................

5

Work Flow  .................................................................

5

Generic Squeak and Rattle Troubleshooting  ............

7

Diagnostic Worksheet  ...............................................

9

CLIP AND FASTENER .......................................

11

Clip and Fastener ....................................................

11

FRONT BUMPER  ...............................................

14

Component Parts Location ......................................

14

Removal and Installation .........................................

15

REAR BUMPER  .................................................

17

Component Parts Location ......................................

17

Removal and Installation .........................................

18

FRONT GRILLE  .................................................

22

Component Parts Location ......................................

22

Removal and Installation .........................................

22

COWL TOP .........................................................

23

Component Parts Location ......................................

23

Removal and Installation .........................................

23

FENDER PROTECTOR ......................................

24

Component Parts Location ......................................

24

Removal and Installation .........................................

24

DOOR OUTSIDE MOLDING  .............................

25

Component Parts Location  ......................................

25

Removal and Installation  .........................................

25

DOOR OUTSIDE LOWER MOLDING ...............

26

Component Parts Location  ......................................

26

Removal and Installation  .........................................

26

DOOR PARTING SEAL  ....................................

27

Component Parts Location  ......................................

27

Removal and Installation  .........................................

27

CENTER MUD GUARD .....................................

29

Component Parts Location  ......................................

29

Removal and Installation  .........................................

29

WINDSHIELD MOLDING  ..................................

30

Component Parts Location  ......................................

30

Removal and Installation  .........................................

30

BACK DOOR WINDOW MOLDING ..................

31

Component Parts Location  ......................................

31

Removal and Installation  .........................................

31

ROOF SIDE MOLDING  .....................................

32

Component Parts Location  ......................................

32

Removal and Installation  .........................................

32

ROOF RAIL  .......................................................

33

Component Parts Location  ......................................

33

Removal and Installation  .........................................

33

BACK DOOR FINISHER  ...................................

35

Component Parts Location  ......................................

35

Removal and Installation  .........................................

35

DOOR FINISHER  ..............................................

36

Component Parts Location  ......................................

36

Removal and Installation  .........................................

36

BODY SIDE TRIM  .............................................

38

Component Parts Location  ......................................

38

Removal and Installation  .........................................

38

EI-2

FLOOR TRIM  .....................................................

41

Component Parts Location  .....................................

41

Removal and Installation  ........................................

41

HEADLINING .....................................................

43

Component Parts Location  .....................................

43

Removal and Installation  ........................................

44

LUGGAGE FLOOR TRIM ..................................

45

Component Parts Location  .....................................

45

Removal and Installation .........................................

46

BACK DOOR TRIM ...........................................

47

Component Parts Location  .....................................

47

Removal and Installation .........................................

47

PRECAUTIONS

EI-3

< SERVICE INFORMATION >

C

D

E

F

G

H

J

K

L

M

A

B

EI

N

O

P

SERVICE INFORMATION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT 
PRE-TENSIONER"

INFOID:0000000001612896

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SUPPLEMENTAL RESTRAINT SYS-
TEM” and “SEAT BELTS” of this Service Manual.

WARNING:

• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SUPPLEMENTAL RESTRAINT SYSTEM”.

• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this

Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.

Precaution for Procedure without Cowl Top Cover

INFOID:0000000001612888

When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.

Precaution for Work

INFOID:0000000001328053

• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their

operation.

• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.

PIIB3706J