Infiniti FX35, FX50 (S51). Manual - part 1888

FLUID COOLER SYSTEM

TM-359

< REMOVAL AND INSTALLATION >

[7AT: RE7R01B (VK50VE)]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

FLUID COOLER SYSTEM

Exploded View

INFOID:0000000005250361

Removal and Installation

INFOID:0000000005250362

REMOVAL

1.

Shift the selector lever to “N” position, and release the parking brake.

2.

Remove air duct (inlet). Refer to 

EM-177, "Exploded View"

.

3.

Remove engine under cover with a power tool. Refer to 

EXT-31, "Exploded View"

.

4.

Remove A/T fluid cooler hose A and A/T fluid cooler hose B.

5.

Disconnect heated oxygen sensor 2 connectors (A).

6.

Remove heated oxygen sensor 2 harness (B) from clips (1).

7.

Remove harness bracket (2) from A/T assembly. Refer to 

TM-

362, "Exploded View"

.

8.

Remove front propeller shaft. Refer to 

DLN-111, "VK50VE :

Exploded View"

.

9.

Remove front drive shaft (right side). Refer to 

FAX-26,

"Exploded View"

.

10. Remove A/T fluid cooler tubes from A/T assembly and engine assembly.

11. Plug up opening such as the A/T fluid cooler tube hole.

1.

A/T assembly

2.

Copper washer

3.

A/T fluid cooler tube

4.

A/T fluid cooler tube

5.

Clip

6.

Bracket

7.

Hose clamp

8.

A/T fluid cooler hose B

9.

A/T fluid cooler hose A 

A.

To radiator

Refer to 

GI-4, "Components"

 for symbols in the figure.

JPDIA0855GB

: Vehicle front

JPDIA0902ZZ

TM-360

< REMOVAL AND INSTALLATION >

[7AT: RE7R01B (VK50VE)]

FLUID COOLER SYSTEM

12. Remove clips and bracket.

13. Remove A/T fluid cooler tubes from the vehicle.

CAUTION:

Be careful not to bend A/T fluid cooler tubes.

INSTALLATION

Note the following, and install in the reverse order of removal.

CAUTION:

Never reuse copper washer.
• Refer to the following when installing A/T fluid cooler hoses.

*: Refer to the illustrations for the specific position each hose clamp tab.

- The illustrations indicate the view from the hose ends.

- When installing hose clamps center line of each hose clamp tab

should be positioned as shown in the figure.

- Insert A/T fluid cooler hoses according to dimension “L” described below.

Hose name

Hose end

Paint mark

Position of hose clamp

*

A/T fluid cooler hose A

Radiator assembly side

Facing backward

A

A/T fluid cooler tube side

Facing downward

B

A/T fluid cooler hose B

Radiator assembly side

Facing downward

C

A/T fluid cooler tube side

Facing downward

B

 D

: Vehicle front

 E

: Vehicle upper

JSDIA0795ZZ

(1)

(2)

Tube type

Dimension “L”

A/T fluid cooler hose A

Radiator assembly side

A

End reaches the radius curve end.

A/T fluid cooler tube side

B

30 mm (1.18 in) [End reaches the 2-stage bulge 
(D).]

A/T fluid cooler hose B

Radiator assembly side

C

Insert the hose until the hose touches the radiator.

A/T fluid cooler tube side

B

30 mm (1.18 in) [End reaches the 2-stage bulge 
(D).]

JSDIA0882ZZ

FLUID COOLER SYSTEM

TM-361

< REMOVAL AND INSTALLATION >

[7AT: RE7R01B (VK50VE)]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

- Set hose clamps (1) at the both ends of A/T fluid cooler hoses (2)

with dimension “A” from the hose edge.

- Hose clamp should not interfere with the bulge of fluid cooler tube.

Inspection and Adjustment

INFOID:0000000005250363

INSPECTION AFTER INSTALLATION

Check A/T fluid leakage.

ADJUSTMENT AFTER INSTALLATION

Adjust A/T fluid level. Refer to 

TM-343, "Adjustment"

.

Dimension “A”

: 5 – 9 mm (0.20 – 0.35 in)

SCIA8123E

TM-362

< UNIT REMOVAL AND INSTALLATION >

[7AT: RE7R01B (VK50VE)]

TRANSMISSION ASSEMBLY

UNIT REMOVAL AND INSTALLATION

TRANSMISSION ASSEMBLY

Exploded View

INFOID:0000000005250364

Removal and Installation

INFOID:0000000005250365

REMOVAL

CAUTION:

• When removing the A/T assembly from engine, first remove the crankshaft position sensor (POS)

from the A/T assembly.

• Be careful not to damage sensor edge.
• Always insert a wooden block between oil pan (upper) of engine and front suspension member when

removing A/T assembly from the engine.  (Because VVEL control shaft position sensor may be dam-
aged by the interference between VVEL control shaft position sensor and dash panel if the operation
is performed without the wooden block inserted.)

1.

Shift the selector lever to “P” position, and then release the parking brake.

2.

Disconnect the battery cable from the negative terminal.

3.

Remove control rod from A/T shift selector. Refer to 

TM-350, "Exploded View"

.

4.

Remove propeller shaft assembly (rear). Refer to 

DLN-134, "Exploded View"

.

5.

Remove propeller shaft assembly (front). Refer to 

DLN-111, "VK50VE : Exploded View"

.

6.

Remove manual lever. Refer to 

TM-353, "Exploded View"

.

7.

Remove crankshaft position sensor (POS) from A/T assembly. Refer to 

EM-188, "Exploded View"

.

CAUTION:

• Never subject it to impact by dropping or hitting it.

1.

Air breather vent

2.

A/T assembly

3.

Bracket

4.

Bracket

5.

Bracket

6.

Bracket

A.

Tightening must be done following the installation procedure. Refer to 

TM-362, "Removal and Installation"

.

Refer to 

GI-4, "Components"

 for symbols in the figure.

JPDIA0848GB