Infiniti FX35, FX50 (S51). Manual - part 1119

BACK DOOR WINDOW GLASS

GW-17

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

GW

N

O

P

Apply primer (if necessary) and then urethane adhesive to the leakage point to stop the leakage.

GW-18

< REMOVAL AND INSTALLATION >

FRONT DOOR GLASS

FRONT DOOR GLASS

Exploded View

INFOID:0000000005235086

Removal and Installation

INFOID:0000000005235087

REMOVAL

1.

Remove front door finisher. Refer to 

INT-11, "Removal and Installation"

.

2.

Remove front door sash inner cover. 

3.

Remove front door inside seal.

4.

Remove the front door grip bracket. Refer to 

INT-11, "Exploded View"

.

5.

Remove both seals (A) as shown in the figure.

1.    Front door glass run

2.

Front door glass 

3.

Module base

4.

Power window motor

5.

Regulator assembly

6.

Front door inside seal

7.

Front door sash inner cover

8.

Front door panel

: Vehicle front

: Clip

JMKIA2659ZZ

JMKIA1945ZZ

FRONT DOOR GLASS

GW-19

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

GW

N

O

P

6.

Reconnect the power window main switch and then operate the
power window main switch to raise or lower the door window
until the glass mounting bolts can be seen.

7.

Remove the front door glass mounting bolts.

8.

Hold securely the front door glass and pull it out of the sash to
remove the door glass.

INSTALLATION

Install in the reverse order of removal.

Inspection and Adjustment

INFOID:0000000005235088

SYSTEM INITIALIZATION

Initialize the system if any of the following work has been done.
• Electric power supply to power window switch or motor is interrupted by blown fuse or disconnecting battery

cable, etc.

• Removal and installation of the regulator assembly.
• Removal and installation of the motor from the regulator assembly.
• Removal and installation of the harness connector of the power window switch.
• Removal and installation of the door glass.
• Removal and installation of the front door glass run.
• Disconnection and connection of the negative terminal of the battery.

 Initialization

Follow the steps below after installing each component to the vehicle.

1.

Disconnect the negative terminal of battery or disconnect power window switch harness connector tempo-
rarily. Then reconnect after at least 1 minute.

2.

Turn ignition switch ON.

3.

Operate power window switch to make over a half of the window open area.

4.

Draw fully the power window switch in the up direction (auto close position) and hold. Continue holding
the switch even when window is completely closed and then release after more than 2 seconds.

5.

Inspect the anti-pinch system function.
NOTE:
Initialization may be cancelled with continuous opening and closing operation. In this case, initialize the
system.

INSPECT THE FUNCTION OF THE ANTI-PINCH SYSTEM

1.

Fully open the door glass.

2.

Place a wooden piece (wooden hammer handle, etc.) at near fully closed position.

3.

Perform fully closing operation with auto up switch.

: Bolt

JMKIA1946ZZ

JMKIA0626ZZ

GW-20

< REMOVAL AND INSTALLATION >

FRONT DOOR GLASS

• Check that the glass reverses without pinching the wooden piece, is lowered approximately 150 mm (5.906

in) or for more than 2 seconds and then stops.

• The glass should not be raised with power window main switch operated while it is reversing or lowering.

CAUTION:

• Be careful not to be pinched.
• Check that the auto up function is normal before the inspection following the system initialization.

FITTING INSPECTION

• Check that the glass is fit securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the

sash is parallel. Loosen the regulator mounting bolts, guide rail mounting bolts, and glass and guide rail
mounting bolts to correct the glass position if the clearance between the glass and sash is not parallel.