Infiniti FX35, FX50 (S51). Manual - part 1066

EXT-14

< REMOVAL AND INSTALLATION >

FRONT BUMPER

6.

Remove front fillet molding (1) fixing screws (A) (LH/RH).

7.

Remove front fillet molding fixing clips (LH/RH).
Refer to 

EXT-32, "Removal and Installation"

.

8.

Remove front fender grommets (A) with a remover tool (B).

9.

Disconnect harness connectors (A) and (B) from back side of
bumper fascia assembly (LH).

10. Remove bumper fascia assembly fixing screws (A) (LH/RH).

11. Remove bumper fascia assembly lower fixing clips (A) and bolts

(B).

: Clip

JMKIA2698ZZ

JMKIA2699ZZ

JMKIA2702ZZ

JMKIA2701ZZ

JMKIA2700ZZ

FRONT BUMPER

EXT-15

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

EXT

N

O

P

12. Pull both side of the bumper fascia assembly toward the vehicle side to disengage both side of the

bumper fascia assembly from bumper side brackets (LH/RH).

13. Remove bumper fascia assembly.

CAUTION:

When removing bumper fascia, 2 workers are required so as to prevent it from dropping.

14. Remove the following parts after removing bumper fascia.

• Hood top seal assembly.
• Front grille. Refer to 

EXT-20, "Removal and Installation"

.

• Front bumper side stiffeners (LH/RH).
• Sonar sensors (LH/RH). Refer to 

AV-359, "FRONT : Removal and Installation"

.

• License plate bracket.
• Front fog lamp finishers (LH/RH).
• Front fog lamps (LH/RH). Refer to 

EXL-231, "Removal and Installation"

.

• Bumper fascia assembly lower.
• Front camera. Refer to 

AV-352, "Removal and Installation"

.

15. Remove bumper energy absorber.

16. Remove bumper reinforcement mounting nuts and bolts, and then remove bumper reinforcement with

power tool.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

Perform camera image calibration. Refer to 

AV-245, "CALIBRATING CAMERA IMAGE (AROUND VIEW

MONITOR) : Description"

.

NOTE:
After installing, perform fitting adjustment.

JMKIA2705ZZ

Portion

Clearance

Surface height difference

Front bumper – Hood

A – A

2.5 – 5.5 mm (0.098 – 0.217 in)

−

2.0 – 0.5 mm (

−

0.079 – 0.020 in)

Front bumper – Front grille

B – B

0.0 – 2.0 mm (0.000 – 0.079 in)

—

Front bumper – Front fender

C – C

0.0 – 0.5 mm (0.000 – 0.020 in)

−

0.5 – 0.5 mm (

−

0.020 – 0.020 in)

Front bumper – Headlamp 

D – D

0.2 – 3.0 mm (0.008 – 0.118 in)

—

Front bumper – Front fender

E – E

0.0 – 0.8 mm (0.000 – 0.031 in)

−

1.0 – 1.0 mm (

−

0.039 – 0.039 in)

Front bumper upper – Front 
bumper lower

F – F

0.0 – 0.7 mm (0.000 – 0.028 in)

—

EXT-16

< REMOVAL AND INSTALLATION >

REAR BUMPER

REAR BUMPER

Exploded View

INFOID:0000000005248859

1.

Bumper side grommet LH

2.

Bumper side bracket LH

3.

Bumper stay LH

4.

Bumper lower retainer

5.

Bumper reinforcement

6.

Energy absorber

JMKIA2706ZZ

REAR BUMPER

EXT-17

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

EXT

N

O

P

Removal and Installation

INFOID:0000000005248860

REMOVAL

CAUTION:

Bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact with
oil.

1.

Fully open back door.

2.

Remove rear combination lamps (LH/RH). Refer to 

EXL-240, "Removal and Installation"

.

3.

Remove bolts (A) and clips (B) (LH/RH) located under rear com-
bination lamps (LH/RH).

4.

Remove rear fillet moldings (1) fixing screws (A) (LH/RH).

5.

Remove rear fillet moldings fixing pawls and clips (LH/RH).
Refer to 

EXT-32, "Removal and Installation"

.

6.

Remove bumper fascia assembly fixing screws (A) (LH/RH). 

7.

Bumper  sub  harness

8.

Rear combination lamp upper finisher 
LH

9.

Rear combination lamp lower finisher 
LH

10. Bumper fascia assembly

11.

Sonar sensor LH

12. Reflex reflector LH

13. Sonar sensor RH

14. Reflex reflector RH

15. Rear combination lamp lower finisher 

RH

16. Rear combination lamp upper finisher 

RH

17. Bumper side grommet RH

18. Bumper stay RH

19. Bumper side bracket RH

JMKIA2708ZZ

: Clip

: Pawl

JMKIA2709ZZ

JMKIA2710ZZ