Infiniti EX35. Manual - part 803

 

  Index      Infiniti     Infiniti EX35 - service repair manual 2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  801  802  803  804   ..

 

 

Infiniti EX35. Manual - part 803

 

 

EXL-256

< COMPONENT DIAGNOSIS >

[HALOGEN TYPE]

HAZARD SWITCH

Does continuity exist?

YES

>> GO TO 3.

NO

>> Repair the harnesses or connectors.

3.

CHECK HAZARD SWITCH SIGNAL SHORT CIRCUIT

Check continuity between the multifunction switch harness connector and the ground.

Does continuity exist?

YES

>> Repair the harnesses or connectors.

NO

>> GO TO 4.

4.

CHECK HAZARD SWITCH GROUND OPEN CIRCUIT

Check continuity between the multifunction switch harness connector and the ground.

Does continuity exist?

YES

>> Replace the hazard switch (multifunction switch).

NO

>> Repair the harnesses or connectors.

Multifunction switch

BCM

Continuity

Connector

Terminal

Connector

Terminal

M72

16

M122

110

Existed

Multifunction switch

Ground

Continuity

Connector

Terminal

M72

16

Not existed

Multifunction switch

Ground

Continuity

Connector

Terminal

M72

1

Existed

TAIL LAMP CIRCUIT

EXL-257

< COMPONENT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

TAIL LAMP CIRCUIT

Component Function Check

INFOID:0000000003756992

1.

CHECK TAIL LAMP OPERATION

IPDM E/R AUTO ACTIVE TEST

1.

Activate IPDM E/R auto active test. Refer to 

EXL-37, "Diagnosis Description"

.

2.

Check that the tail lamp is turned ON.

CONSULT-III ACTIVE TEST

1.

Select "EXTERNAL LAMPS" of IPDM E/R active test item.

2.

With operating the test items, check that the tail lamp is turned ON.

Is the tail lamp turned ON?

YES

>> Tail lamp circuit is normal.

NO

>> Refer to 

EXL-257, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000003756993

1.

CHECK TAIL LAMP FUSE

1.

Turn the ignition switch OFF.

2.

Check that the following fuses are not fusing.

Is the fuse fusing?

YES

>> Repair the malfunctioning part before replacing the fuse.

NO

>> GO TO 2.

2.

CHECK TAIL LAMP OUTPUT VOLTAGE

CONSULT-III ACTIVE TEST

1.

Disconnect the rear combination lamp connector.

2.

Turn the ignition switch ON.

3.

Select "EXTERNAL LAMPS" of IPDM E/R active test item.

4.

With operating the test items, check the voltage between the IPDM E/R harness connector and the
ground.

Is the measurement value normal?

YES

>> GO TO 3.

NO

>> Replace IPDM E/R.

3.

CHECK TAIL LAMP OPEN CIRCUIT

1.

Turn the ignition switch OFF.

2.

Disconnect IPDM E/R connector.

TAIL

: Tail lamp ON

Off

: Tail lamp OFF

Unit

Location

Fuse No.

Capacity

• Tail lamp
• Rear side marker lamp
• License plate lamp

IPDM E/R

#53

10 A

Terminals

Test item

Voltage

(Approx.)

(+)

(

)

IPDM E/R

Ground

EXTERNAL 

LAMP

Connector

Terminal

E5

7

TAIL

Battery volt-

age

Off

0 V

EXL-258

< COMPONENT DIAGNOSIS >

[HALOGEN TYPE]

TAIL LAMP CIRCUIT

3.

Check continuity between the IPDM E/R harness connector and the rear combination lamp harness con-
nector.

Does continuity exist?

YES

>> GO TO 4.

NO

>> Repair the harnesses or connectors.

4.

CHECK TAIL LAMP GROUND OPEN CIRCUIT

Check continuity between the rear combination lamp harness connector and the ground.

Does continuity exist?

YES

>> Replace the rear combination lamp.

NO

>> Repair the harnesses or connectors.

IPDM E/R

Rear combination lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E5

7

B232

1

Existed

LH

B60

1

Rear combination lamp

Ground

Continuity

Connector

Terminal

RH

B232

4

Existed

LH

B60

4

LICENSE PLATE LAMP CIRCUIT

EXL-259

< COMPONENT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

LICENSE PLATE LAMP CIRCUIT

Component Function Check

INFOID:0000000003756994

NOTE:
Check the tail lamp circuit if the tail lamp and the license plate lamp are not turned ON.

1.

CHECK LICENSE PLATE LAMP OPERATION

IPDM E/R AUTO ACTIVE TEST

1.

Activate IPDM E/R auto active test. Refer to 

EXL-37, "Diagnosis Description"

.

2.

Check that the license plate lamp is turned ON.

CONSULT-III ACTIVE TEST

1.

Select "EXTERNAL LAMPS" of IPDM E/R active test item.

2.

With operating the lighting switch, check that the license plate lamp is turned ON.

Is the license plate lamp turned ON?

YES

>> License plate lamp circuit is normal.

NO

>> Refer to 

EXL-259, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000003756995

1.

CHECK LICENSE PLATE LAMP BULB

Check the applicable lamp bulb.

Is the bulb normal?

YES

>> GO TO 2.

NO

>> Replace the bulb.

2.

CHECK LICENSE PLATE LAMP OPEN CIRCUIT

1.

Turn the ignition switch OFF.

2.

Disconnect IPDM E/R connector and the license plate lamp connector.

3.

Check continuity between the IPDM E/R harness connector and the license plate lamp harness connec-
tor.

Does continuity exist?

YES

>> GO TO 3.

NO

>> Repair the harnesses or connectors.

3.

CHECK LICENSE PLATE LAMP GROUND OPEN CIRCUIT

Check continuity between the license plate lamp harness connector and the ground.

Does continuity exist?

YES

>> Replace the license plate lamp.

NO

>> Repair the harnesses or connectors.

TAIL

: License plate lamp ON

Off

: License plate lamp OFF

IPDM E/R

License plate lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E5

7

D117

1

Existed

LH

D112

1

License plate lamp

Ground

Continuity

Connector

Terminal

RH

D117

2

Existed

LH

D112

2

 

 

 

 

 

 

 

Content   ..  801  802  803  804   ..