Infiniti EX35. Manual - part 414

 

  Index      Infiniti     Infiniti EX35 - service repair manual 2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  412  413  414  415   ..

 

 

Infiniti EX35. Manual - part 414

 

 

CCS

PRECAUTIONS

CCS-191

< PRECAUTION >

[LDW & LDP]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT 
PRE-TENSIONER"

INFOID:0000000003554306

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.

WARNING:

• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.

• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this

Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.

Precaution for LDW/LDP System Service

INFOID:0000000003514643

WARNING:

Be careful of traffic conditions and safety around the vehicle when performing road test.

CAUTION:

• Never use the LDP system when driving with free rollers or a chassis dynamometer.
• Never perform the active test while driving.
• Never disassemble and remodel the lane camera unit.
• Do not use the lane camera unit that is removed from the vehicle.
• Never change LDW initial state ON 

 OFF without the consent of the customer. 

To keep the LDW/LDP system operating properly, be sure to observe the following items:
• Always keep the windshield clean. The sensing capability of the camera unit depends on the condi-

tion of the windshield. See “Appearance and care” for cleaning instructions.

• Never strike or damage the areas around the lane camera unit.
• Never touch the camera lens.
• Never attach a sticker (including transparent material) or install an accessory near the lane camera

unit.

• Never place reflective materials, such as a white paper or mirrors on the instrument panel. Reflection

of the sunlight may adversely affect the camera unit's lane marker detection capability.

CCS-192

< ON-VEHICLE REPAIR >

[LDW & LDP]

LANE CAMERA UNIT

ON-VEHICLE REPAIR

LANE CAMERA UNIT

Exploded View

INFOID:0000000003514644

Removal and Installation

INFOID:0000000003514645

REMOVAL

1.

Remove the lane camera cover.

2.

Remove the bolts.

3.

Disconnect lane camera unit connector, and remove lane camera unit.

NOTE:
When replace the lane camera bracket, remove the headlining assembly.

INSTALLATION

Installation is the reverse order of removal.

CAUTION:

• Remove the camera lens cap for replacement.
• Never give an impact to the lane camera unit.
• Perform the camera aiming every time the lane camera unit is removed and installed. Refer to 

CCS-

112, "CAMERA AIMING ADJUSTMENT : Description"

.

1.

Lane camera bracket

2.

Lane camera unit

3.

Lane camera cover

JPOIA0123ZZ

CCS

LDW SWITCH

CCS-193

< ON-VEHICLE REPAIR >

[LDW & LDP]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

LDW SWITCH

Exploded View

INFOID:0000000003514646

Removal and Installation

INFOID:0000000003514647

REMOVAL

1.

Remove the instrument driver lower panel. Refer to 

IP-11, "Exploded View"

.

2.

Disengage the pawl. Then remove LDW switch.

INSTALLATION

Install in the reverse order of removal.

1.

LDW switch

A.

Pawls

JPOIA0124ZZ

CCS-194

< ON-VEHICLE REPAIR >

[LDW & LDP]

LANE DEPARTURE WARNING BUZZER

LANE DEPARTURE WARNING BUZZER

Exploded View

INFOID:0000000003514648

Removal and Installation

INFOID:0000000003514649

REMOVAL

1.

Remove the cluster lid C assembly. Refer to 

IP-11, "Exploded View"

.

2.

Remove the AV control unit.

3.

Remove the screw.

4.

Disconnect the connector. And remove lane departure warning buzzer.

INSTALLATION

Installation is the reverse order of removal.

1.

Lane departure warning buzzer

JPOIA0125ZZ

 

 

 

 

 

 

 

Content   ..  412  413  414  415   ..