Infiniti EX35. Manual - part 334

 

  Index      Infiniti     Infiniti EX35 - service repair manual 2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  332  333  334  335   ..

 

 

Infiniti EX35. Manual - part 334

 

 

C1116 STOP LAMP SWITCH

BRC-51

< COMPONENT DIAGNOSIS >

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

C1116 STOP LAMP SWITCH

Description

INFOID:0000000003132908

The stop lamp switch transmits the stop lamp switch signal (ON/OFF) to the ABS actuator and electric unit
(control unit). 

DTC Logic

INFOID:0000000003132909

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

DTC REPRODUCTION PROCEDURE

1.

Turn the ignition switch ON.

2.

Perform ABS actuator and electric unit (control unit) self-diagnosis.

Is DTC “C1116” detected?

YES

>> Proceed to diagnosis procedure. Refer to 

BRC-51, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003132910

1.

CHECK CONNECTOR

1.

Turn the ignition switch OFF.

2.

Disconnect ABS actuator and electric unit (control unit) connector.

3.

Disconnect stop lamp switch connector.

4.

Check terminal for deformation, disconnection, looseness, etc.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace damaged parts.

2.

CHECK STOP LAMP SWITCH

Check stop lamp switch. Refer to 

BRC-51, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace stop lamp switch.

3.

CHECK STOP LAMP SWITCH CIRCUIT

Check the voltage between ABS actuator and electric unit (control unit) harness connector and ground.

Is the inspection result normal?

YES

>> Replace ABS actuator and electric unit (control unit).

NO

>> Repair or replace damaged parts.

Component Inspection

INFOID:0000000003132911

1.

CHECK STOP LAMP SWITCH

DTC

Display item

Malfunction detected condition

Possible cause

C1116

STOP LAMP SW

When stop lamp switch circuit is open.

• Harness or connector
• Stop lamp switch
• ABS actuator and electric unit 

(control unit)

ABS actuator and electric unit (control unit)

Condition

Voltage

Connector

Terminal

E41

30

Brake pedal is depressed

Battery voltage

Brake pedal is released

Approx. 0 V

BRC-52

< COMPONENT DIAGNOSIS >

[VDC/TCS/ABS]

C1116 STOP LAMP SWITCH

1.

Turn the ignition switch OFF.

2.

Disconnect stop lamp switch connector.

3.

Check the continuity between stop lamp switch connector terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace stop lamp switch. Refer to 

BR-18, "Exploded View"

.

Special Repair Requirement

INFOID:0000000003430139

1.

ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION

Always perform the neutral position adjustment for the steering angle sensor, when replacing the ABS actua-
tor and electric unit (control unit). Refer to 

BRC-8, "ADJUSTMENT OF STEERING ANGLE SENSOR NEU-

TRAL POSITION : Description"

.

>> END

Stop lamp switch

Condition

Continuity

Terminal

1 – 2 (With ICC models)

 4 (Without ICC models)

Release stop lamp switch
(When brake pedal is depressed.)

Existed

Push stop lamp switch
(When brake pedal is released.)

Not existed

C1120, C1122, C1124, C1126 IN ABS SOL

BRC-53

< COMPONENT DIAGNOSIS >

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

C1120, C1122, C1124, C1126 IN ABS SOL

Description

INFOID:0000000003132913

The solenoid valve increases, holds or decreases the fluid pressure of each brake caliper according to the sig-
nals transmitted by the ABS actuator and electric unit (control unit). 

DTC Logic

INFOID:0000000003132914

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

DTC REPRODUCTION PROCEDURE

1.

Turn the ignition switch ON.

2.

Perform ABS actuator and electric unit (control unit) self-diagnosis.

Is DTC “C1120”, “C1122”, “C1124” or “C1126” detected?

YES

>> Proceed to diagnosis procedure. Refer to 

BRC-53, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003132915

1.

CHECK CONNECTOR

1.

Turn the ignition switch OFF.

2.

Disconnect ABS actuator and electric unit (control unit) connector.

3.

Check terminal for deformation, disconnection, looseness, etc.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace damaged parts.

2.

CHECK SOLENOID, VDC SWITCH-OVER VALVE AND ACTUATOR RELAY POWER SUPPLY CIRCUIT

Check the voltage between ABS actuator and electric unit (control unit) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace damaged parts.

3.

CHECK SOLENOID, VDC SWITCH-OVER VALVE AND ACTUATOR RELAY GROUND CIRCUIT

Check the continuity between ABS actuator and electric unit (control unit) harness connector and ground.

DTC

Display item

Malfunction detected condition

Possible cause

C1120

FR LH IN ABS SOL

When the control unit detects a malfunction in the front 
LH inlet solenoid circuit.

ABS actuator and electric unit 
(control unit)

C1122

FR RH IN ABS SOL

When the control unit detects a malfunction in the front 
RH inlet solenoid circuit.

C1124

RR LH IN ABS SOL

When the control unit detects a malfunction in the rear LH 
inlet solenoid circuit.

C1126

RR RH IN ABS SOL

When the control unit detects a malfunction in the rear 
RH inlet solenoid circuit.

ABS actuator and electric unit (control unit)

Voltage

Connector

Terminal

E41

3

Ground

Battery voltage

BRC-54

< COMPONENT DIAGNOSIS >

[VDC/TCS/ABS]

C1120, C1122, C1124, C1126 IN ABS SOL

Is the inspection result normal?

YES

>> Replace ABS actuator and electric unit (control unit).

NO

>> Repair or replace damaged parts.

Component Inspection

INFOID:0000000003132916

1.

CHECK ACTIVE TEST

1.

Select each test menu item on ”ACTIVE TEST“.

2.

On the display, touch “Up”, “Keep” and “Down”, and check that the system operates as shown in the table
below.

*: On for 1 to 2 seconds after the touch, and then Off.

NOTE:

A brief moment of On/Off condition occurs every 20 seconds after ignition switch turned ON. This is not malfunction because it is
an operation for checking.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Proceed to diagnosis procedure. Refer to 

BRC-53, "Diagnosis Procedure"

.

Special Repair Requirement

INFOID:0000000003430141

1.

ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION

Always perform the neutral position adjustment for the steering angle sensor, when replacing the ABS actua-
tor and electric unit (control unit). Refer to 

BRC-8, "ADJUSTMENT OF STEERING ANGLE SENSOR NEU-

TRAL POSITION : Description"

.

>> END

ABS actuator and electric unit (control unit)

Continuity

Connector

Terminal

E41

1

Ground

Existed

4

Test item

Display item

Display (Note)

Up

Keep

Down

FR RH SOL

FR RH IN SOL

Off

On

On

FR RH OUT SOL

Off

Off

On*

USV[FR-RL]

Off

Off

Off

HSV[FR-RL]

Off

Off

Off

FR LH SOL

FR LH IN SOL

Off

On

On

FR LH OUT SOL

Off

Off

On*

USV[FL-RR]

Off

Off

Off

HSV[FL-RR]

Off

Off

Off

RR RH SOL

RR RH IN SOL

Off

On

On

RR RH OUT SOL

Off

Off

On*

USV[FL-RR]

Off

Off

Off

HSV[FL-RR]

Off

Off

Off

RR LH SOL

RR LH IN SOL

Off

On

On

RR LH OUT SOL

Off

Off

On*

USV[FR-RL]

Off

Off

Off

HSV[FR-RL]

Off

Off

Off

 

 

 

 

 

 

 

Content   ..  332  333  334  335   ..