Infiniti EX35. Manual - part 1391

POWER STEERING OIL PUMP

ST-45

< ON-VEHICLE REPAIR >

C

D

E

F

H

I

J

K

L

M

A

B

ST

N

O

P

POWER STEERING OIL PUMP

Exploded View

INFOID:0000000003134407

REMOVAL 

DISASSEMBLY 

1.

Power steering oil pump

2.

Bracket

: Vehicle front

Refer to 

GI-4, "Components"

 for symbols in the figure.

JSGIA0046GB

1.

Pulley

2.

Oil seal

3.

Bracket

4.

Body assembly

5.

Suction pipe

6.

O-ring 

7.

Flow control valve B assembly

8.

Flow control valve spring

9.

Flow control valve A

JSGIA0364GB

ST-46

< ON-VEHICLE REPAIR >

POWER STEERING OIL PUMP

Removal and Installation

INFOID:0000000003134408

REMOVAL

1.

Drain power steering fluid from reservoir tank.

2.

Remove the right of the air cleaner and the right of the air duct. Refer to 

EM-27, "Exploded View"

.

3.

Loosen drive belt. Refer to 

EM-13, "Exploded View"

.

4.

Remove drive belt from oil pump pulley.

5.

Remove pressure sensor connector.

6.

Remove copper washers and eye bolt (drain fluid from their pipings).

7.

Remove suction hose (drain fluid from their pipings).

8.

Remove oil pump mounting bolts, and then remove oil pump.

INSTALLATION

Note the following, and install in the reverse order of removal.
• When installing suction hoses (1), refer to the figure.

CAUTION:

• Never apply fluid to the hose (1) and tube (2).
• Insert hose securely until it contacts spool (A) of tube.
• Leave clearance (L) when installing clamp (3).

• When installing eye bolt (1) and copper washer (2) to oil pump (3),

refer to the figure.

CAUTION:

• Never reuse copper washer.
• Apply power steering fluid to around copper washers, then

install eye bolt.

• Install eye bolt with eye joint (assembled to high pressure

hose) (B) protrusion (A) facing with pump side cutout, and
then tighten it to the specified torque after tightening by
hand. Refer to 

ST-51, "2WD : Exploded View"

 (2WD models),

ST-52, "AWD : Exploded View"

 (AWD models).

• Securely insert harness connector to pressure sensor.

• Adjust belt tension. Refer to 

EM-13, "Tension Adjustment"

.

• Check fluid level, fluid leakage and air bleeding hydraulic system after the installation. Refer to 

ST-11,

"Inspection"

.

Disassembly and Assembly

INFOID:0000000003134409

DISASSEMBLY

1.

Remove rear cover mounting bolts, and then remove rear cover from body assembly.

CAUTION:

10. Dowel pin

11.

Front side plate

12. Vane

13. Rotor

14. Rotor snap ring

15. Cam ring 

16. Rear side plate

17. O-ring

18. Teflon ring

19. O-ring

20. Rear cover

21. Cartridge

A.

Oil seal lip

: Apply power steering fluid.

: Apply multi-purpose grease.

Refer to 

GI-4, "Components"

 for symbols not described on the above.

Standard

L

: 3 – 8 mm (0.12 – 0.31 in)

JSGIA0118ZZ

SGIA1379E

POWER STEERING OIL PUMP

ST-47

< ON-VEHICLE REPAIR >

C

D

E

F

H

I

J

K

L

M

A

B

ST

N

O

P

• Fix oil pump with a vise if necessary.
• Use copper plates when fixing with a vise.

2.

Remove O-ring from body assembly.

3.

Remove rear side plate from cartridge, and then remove Teflon ring and O-ring from rear side plate.

4.

Remove rotor snap ring using a snap ring pliers, and remove
pulley from body assembly.

CAUTION:

Remove pulley so as not to be damaged when removing
rotor snap ring.

5.

Remove cartridge and front side plate.

6.

Remove flow control valve A (1), flow control valve spring (2)
and flow control valve B assembly (3) from body assembly (4).

CAUTION:

Never drop and damage flow control valve A and flow con-
trol valve B assembly when removing.

7.

Remove oil seal from body assembly.

8.

Remove mounting bolt of suction pipe, and then remove suction
pipe from body assembly.

9.

Remove O-ring from body assembly.

10. Remove bracket mounting bolts, and then remove bracket from

body assembly.

ASSEMBLY

1.

Apply recommended grease to oil seal lips. Apply recommended
fluid to around oil seal, and then install oil seal to body assembly
using a drift [SST: ST35300000 (

—

)]

CAUTION:

• Fix oil pump with a vise if necessary.
• Use copper plates when fixing with a vise.

2.

Install bracket to body assembly.

3.

If dowel pin has been removed, insert it into body assembly by
hand. If it cannot be inserted by hand, lightly tap with a hammer.

4.

Install flow control valve A (1), flow control valve spring (2) and
flow control valve B assembly (3) to body assembly (4).

SGIA0059E

JSGIA0365ZZ

SGIA0527E

JSGIA0365ZZ

ST-48

< ON-VEHICLE REPAIR >

POWER STEERING OIL PUMP

5.

Install front side plate (3) with dowel pin (2) on flow control valve
A (1) side as shown in the figure aligning with front side plate
cutout (A) to body assembly (4).

6.

Install cam ring as shown in the figure.

7.

Install pulley to body assembly.

CAUTION:

Never damage oil seal when installing pulley.

8.

Install rotor so that mark faces body assembly, and then install it
to pulley shaft.

9.

Install vane to rotor so that arc of vane faces cam ring side.

10. Install rotor snap ring to slit of pulley shaft using a hammer and a

10 mm (0.39 in) box.

CAUTION:

• Never damage rotor and pulley shaft.
• Oil pump assembly must be replaced if rotor is damaged.

SGIA1189E

SGIA0612E

SGIA0989E

SGIA0613E

SGIA0063E