Infiniti EX35. Manual - part 1287

 

  Index      Infiniti     Infiniti EX35 - service repair manual 2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1285  1286  1287  1288   ..

 

 

Infiniti EX35. Manual - part 1287

 

 

SEC-44

< COMPONENT DIAGNOSIS >

[INTELLIGENT KEY SYSTEM]

B2190 NATS ANTENNA AMP.

1.

Turn ignition switch OFF.

2.

Disconnect key slot connector.

3.

Check continuity between key slot harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Repair or replace harness or connector.

8.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-38, "Intermittent Incident"

.

>> INSPECTION END

Key slot

Ground

Continuity

Connector

Terminal

M22

7

Existed

B2191 DIFFERENCE OF KEY

SEC-45

< COMPONENT DIAGNOSIS >

[INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B2191 DIFFERENCE OF KEY

Description

INFOID:0000000003586516

Performs ID verification through BCM and Intelligent Key when push-button ignition switch is pressed.
Prohibits the release of steering lock or start of engine when an unregistered ID of Intelligent Key is used.

DTC Logic

INFOID:0000000003586517

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Press the push-button ignition switch

2.

Check “Self diagnostic result” with CONSULT-III.

Is DTC detected?

YES

>> Go to 

SEC-45, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003586518

1.

PERFORM INITIALIZATION

Perform initialization with CONSULT-III. Re-register all Intelligent Keys.
For initialization and registration of Intelligent Key. Refer to “CONSULT-III Operation Manual NATS-IVIS/
NVIS”.

Can the system be initialized and can the engine be started with re-registered Intelligent Key?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

REPLACE INTELLIGENT KEY

1.

Replace Intelligent Key.

2.

Perform initialization with CONSULT-III. 
For initialization and registration of Intelligent Key. Refer to “CONSULT-III Operation Manual NATS-IVIS/
NVIS”.

Can the system be initialized and can the engine be started with re-registered Intelligent Key?

YES

>> INSPECTION END

NO

>> GO TO 3.

3.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-38, "Intermittent Incident"

.

>> INSPECTION END

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B2191

DIFFERENCE OF KEY

The ID verification results between BCM and Intelligent 
Key are NG. The registration is necessary.

Intelligent Key

SEC-46

< COMPONENT DIAGNOSIS >

[INTELLIGENT KEY SYSTEM]

B2192 ID DISCORD, IMMU-ECM

B2192 ID DISCORD, IMMU-ECM

Description

INFOID:0000000003586519

BCM performs the ID verification with ECM that allows the engine to start. Start the engine if the ID is OK.
ECM prevents the engine from starting if the ID is not registered. BCM starts the communication with ECM if
ignition switch is turned ON.

DTC Logic

INFOID:0000000003586520

DTC DETECTION LOGIC

NOTE:
• If DTC B2192 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

SEC-32, "BCM : DTC Logic"

.

• If DTC B2192 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

SEC-34, "BCM : DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON under the following conditions.

-

Selector lever is in the P or N position.

-

Do not depress brake pedal.

2.

Check “Self diagnostic result” with CONSULT-III.

Is DTC detected?

YES

>> Go to 

SEC-46, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003586521

1.

PERFORM INITIALIZATION

Perform initialization with CONSULT-III. Re-register all Intelligent Keys.
For initialization and registration of Intelligent Key. Refer to “CONSULT-III Operation Manual NATS-IVIS/
NVIS”.

Can the system be initialized and can the engine be started with re-registered Intelligent Key?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-84, "Removal and Installation"

.

2.

Perform initialization with CONSULT-III. 
For initialization, refer to “CONSULT-III Operation Manual NATS-IVIS/NVIS”.

Can the system be initialized and can the engine be started with re-registered Intelligent Key?

YES

>> INSPECTION END

NO

>> GO TO 3.

3.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-38, "Intermittent Incident"

.

>> INSPECTION END

DTC No.

Trouble diagnosis 

name

DTC detecting condition

Possible cause

B2192

ID DISCORD, IMMU-
ECM

The ID verification results between BCM and ECM 
are NG. The registration is necessary.

• BCM
• ECM

B2193 CHAIN OF ECM-IMMU

SEC-47

< COMPONENT DIAGNOSIS >

[INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B2193 CHAIN OF ECM-IMMU

Description

INFOID:0000000003586522

BCM performs the ID verification with ECM that allows the engine to start. Start the engine if the ID is OK.
ECM prevents the engine from starting if the ID is not registered. BCM starts the communication with ECM if
ignition switch is turned ON.

DTC Logic

INFOID:0000000003586523

DTC DETECTION LOGIC

NOTE:
• If DTC B2193 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

SEC-32, "BCM : DTC Logic"

.

• If DTC B2193 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

SEC-34, "BCM : DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON under the following conditions.

-

Selector lever is in the P or N position.

-

Do not depress brake pedal.

2.

Check “Self diagnostic result” with CONSULT-III.

Is DTC detected?

YES

>> Go to 

SEC-47, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003586524

1.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-84, "Removal and Installation"

.

2.

Perform initialization with CONSULT-III.
For initialization, refer to “CONSULT-III Operation Manual NATS-IVIS/NVIS”.

Does the engine start?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

REPLACE ECM

Replace ECM. Refer to 

EC-15, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description"

.

>> INSPECTION END

DTC No.

Trouble diagnosis 

name

DTC detecting condition

Possible cause

B2193

CHAIN OF ECM-
IMMU

Inactive communication between ECM and BCM

• Harness or connectors

(The CAN communication line is 
open or shorted)

• BCM 
• ECM

 

 

 

 

 

 

 

Content   ..  1285  1286  1287  1288   ..