Infiniti EX35. Manual - part 1058

 

  Index      Infiniti     Infiniti EX35 - service repair manual 2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1056  1057  1058  1059   ..

 

 

Infiniti EX35. Manual - part 1058

 

 

MA-22

< ON-VEHICLE MAINTENANCE >

CHASSIS MAINTENANCE

• Using ATF other than Genuine NISSAN Matic S ATF or Matic J ATF will cause deterioration in

driveability and A/T durability, and may damage the A/T, which is not covered by the INFINITI new
vehicle limited warranty.

• When filling ATF, be careful not to scatter heat generating parts such as exhaust.
• Do not reuse drain plug gasket.

4.

Run engine at idle speed for 5 minutes.

5.

Check A/T fluid level and condition. Refer to 

MA-20, "A/T FLUID : Inspection"

. If ATF is still dirty, repeat

step 2. through 5.

6.

Install the removed A/T fluid level gauge into A/T fluid charging pipe.

TRANSFER FLUID

TRANSFER FLUID : Inspection

INFOID:0000000003759975

FLUID LEAKAGE

Check transfer surrounding area (oil seal, drain plug, and filler plug etc.) for fluid leakage.

FLUID LEVEL

1.

Remove filler plug (1) and gasket. Then check that fluid is filled
up from mounting hole for the filler plug.

CAUTION:

Never start engine while checking fluid level.

2.

Before installing filler plug, set a new gasket. Install filler plug on
transfer and tighten to the specified torque. Refer to 

DLN-53,

"Exploded View"

.

CAUTION:

Never reuse gasket.

TRANSFER FLUID : Draining

INFOID:0000000003759976

1.

Run the vehicle to warm up the transfer unit sufficiently.

2.

Stop the engine, and remove the drain plug (1) to drain the
transfer fluid.

CAUTION:

When draining fluid, protect exhaust tube flange with cover.

3.

Apply sealant to drain plug. Install drain plug on transfer and
tighten to the specified torque. Refer to 

DLN-53, "Exploded

View"

.

Use Genuine Silicone RTV or equivalent. Refer to 

GI-15, "Rec-

ommended Chemical Products and Sealants"

.

CAUTION:

Remove old sealant adhering to mounting surfaces. Also
remove any moisture, oil, or foreign material adhering to
application and mounting surfaces.

Drain plug - tightening torque

: Refer to 

TM-162, "Exploded View"

.

JSDIA0096ZZ

JSDIA0095ZZ

CHASSIS MAINTENANCE

MA-23

< ON-VEHICLE MAINTENANCE >

C

D

E

F

G

H

I

J

K

L

M

B

MA

N

O

A

TRANSFER FLUID : Refilling

INFOID:0000000003759977

1.

Remove filler plug (1) and gasket. Then fill fluid up to mounting
hole for the filler plug.

CAUTION:

Carefully fill the fluid. (Fill up for approximately 3 minutes.)

2.

Leave the vehicle for 3 minutes, and check the fluid level again.

3.

Set a new gasket onto filler plug and install it on transfer and
tighten to the specified torque. Refer to 

DLN-53, "Exploded View"

.

CAUTION:

Never reuse gasket.

FRONT PROPELLER SHAFT: 2S56A

FRONT PROPELLER SHAFT: 2S56A : Inspection

INFOID:0000000003759978

NOISE

Check the propeller shaft tube surface for dents or cracks. If damaged, replace propeller shaft assembly.

VIBRATION

If vibration is present at high speed, inspect propeller shaft runout first.
1.

With a dial indicator, measure propeller shaft runout at runout
measuring points by rotating final drive companion flange with
hands.

2.

If runout still exceeds specifications, separate propeller shaft at
final drive companion flange; then rotate companion flange 90,
180, 270 degrees and install propeller shaft.

3.

Check runout again. If runout still exceeds specifications, replace propeller shaft assembly. 

4.

Check the vibration by driving vehicle.

RUNOUT MEASURING POINT

Propeller shaft runout measuring point (Point “ ”).

REAR PROPELLER SHAFT: 3S80A-R

Fluid and viscosity

: Refer to 

MA-10, "Fluids 

and Lubricants"

.

Fluid capacity

: Refer to 

DLN-71, "General 

Specifications"

.

JSDIA0096ZZ

: Vehicle front

Limit

Propeller shaft runout

: Refer to 

DLN-77, "Propel-

ler Shaft Runout"

.

JPDID0185ZZ

Standard

A

: 381.5 mm (15.02 in)

PDIA0768J

MA-24

< ON-VEHICLE MAINTENANCE >

CHASSIS MAINTENANCE

REAR PROPELLER SHAFT: 3S80A-R : Inspection

INFOID:0000000003759979

NOISE

• Check the propeller shaft tube surface for dents or cracks. If damaged, replace propeller shaft assembly.
• If center bearing is noisy or damaged, replace propeller shaft assembly.

VIBRATION

If vibration is present at high speed, inspect propeller shaft runout first.
1.

With a dial indicator, measure propeller shaft runout at runout
measuring points by rotating final drive companion flange with
hands.

2.

If runout still exceeds specifications, separate propeller shaft at
final drive companion flange; then rotate companion flange 120,
240 degrees and install propeller shaft.

3.

Check runout again. If runout still exceeds specifications,
replace propeller shaft assembly. 

4.

Check the vibration by driving vehicle.

RUNOUT MEASURING POINT

Propeller shaft runout measuring point (Point “ ”).

REAR PROPELLER SHAFT: 3F80A-1VL107

REAR PROPELLER SHAFT: 3F80A-1VL107 : Inspection

INFOID:0000000003759980

NOISE

• Check the propeller shaft tube surface for dents or cracks. If damaged, replace propeller shaft assembly.
• If center bearing is noisy or damaged, replace propeller shaft assembly.

VIBRATION

If vibration is present at high speed, inspect propeller shaft runout first.
1.

With a dial indicator, measure propeller shaft runout at runout
measuring points by rotating final drive companion flange with
hands.

2.

If runout still exceeds specifications, separate propeller shaft at
final drive companion flange, then rotate companion flange 60,
120, 180, 240, 300 degrees and install propeller shaft.

3.

Check runout again. If runout still exceeds specifications,
replace propeller shaft assembly. 

4.

Check the vibration by driving vehicle.

Limit

Propeller shaft runout

: Refer to 

DLN-85, "Propel-

ler Shaft Runout"

.

SDIA1087E

: Vehicle front

Standard

A

: 192 mm (7.56 in)

B

: 172 mm (6.77 in)

C

: 172 mm (6.77 in)

JSDIA0169ZZ

Limit

Propeller shaft runout

: Refer to 

DLN-94, "Propel-

ler Shaft Runout"

.

SDIA1087E

CHASSIS MAINTENANCE

MA-25

< ON-VEHICLE MAINTENANCE >

C

D

E

F

G

H

I

J

K

L

M

B

MA

N

O

A

RUNOUT MEASURING POINT

Propeller shaft runout measuring point (Point “ ”).

FRONT DIFFERENTIAL GEAR OIL: F160A

FRONT DIFFERENTIAL GEAR OIL: F160A : Inspection

INFOID:0000000003759981

OIL LEAKAGE

Make sure that oil is not leaking from final drive assembly or around it.

OIL LEVEL

• Remove filler plug (1) and check oil level from filler plug mounting

hole as shown in the figure.

CAUTION:

Never start engine while checking oil level.

• Set a gasket on filler plug (1) and install it on final drive assembly.

Refer to 

DLN-108, "Exploded View"

.

CAUTION:

Never reuse gasket.

FRONT DIFFERENTIAL GEAR OIL: F160A : Draining

INFOID:0000000003759982

1.

Stop engine.

2.

Remove drain plug (1) and drain gear oil.

3.

Set a gasket on drain plug (1) and install it to final drive assem-
bly and tighten to the specified torque. Refer to 

DLN-108,

"Exploded View"

.

CAUTION:

Never reuse gasket.

: Vehicle front

Standard

A

: 162 mm (6.38 in)

B

: 245 mm (9.65 in)

C

: 185 mm (7.28 in)

PDIA0772J

JPDID0188ZZ

JPDID0189ZZ

 

 

 

 

 

 

 

Content   ..  1056  1057  1058  1059   ..