Dodge Neon / Neon SRT-4. Manual - part 582

 

  Index      Dodge     Dodge Neon / Neon SRT-4 - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  580  581  582  583   ..

 

 

Dodge Neon / Neon SRT-4. Manual - part 582

 

 

Symptom:

P0594-SPEED CONTROL SERVO POWER CIRCUIT

When Monitored and Set Condition:

P0594-SPEED CONTROL SERVO POWER CIRCUIT

When Monitored:

With the ignition key on. The speed control switched on.

Set Condition:

The PCM detects a open or short in the Speed Control Power Supply

circuit. One Trip Fault.

POSSIBLE CAUSES

(V30) S/C BRAKE SWITCH OUTPUT CIRCUIT

(V32) S/C POWER SUPPLY CIRCUIT

(V30) S/C BRAKE SWITCH OUTPUT CIRCUIT SHORTEDTO GROUND

(V32) S/C POWER SUPPLY CIRCUIT SHORTED TO GROUND

(V30) S/C BRAKE SWITCH OUTPUT CIRCUIT OPEN

BRAKE LAMP SWITCH

PCM (S/C SOURCE CIRCUIT)

TEST

ACTION

APPLICABILITY

1

Turn the ignition off.
Disconnect the Speed Control Servo harness connector.
Ignition on, engine not running.
NOTE: It is necessary to PRESS and HOLD the Speed Control Switch in the
ON position while checking for voltage.
Using a 12-volt test light connected to ground, probe the (V30) S/C Brake Switch
Output terminal in the Servo Harness connector.
Does the test light illuminate brightly?

All

Yes

→ Refer to the INTERMITTENT CONDITION symptom in the

Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

→ Go To 2

233

DRIVEABILITY - NGC

TEST

ACTION

APPLICABILITY

2

Turn the ignition off.
Disconnect the PCM harness connector.
Disconnect the Brake Lamp Switch harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (V32) S/C Power Supply circuit from the Brake Lamp
Switch harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 3

No

→ Repair the open/high resistance in the (V32) S/C Power Supply

circuit between the PCM and Brake Switch.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

3

Turn the ignition off.
Disconnect the PCM harness connector.
Disconnect the Brake Switch harness connector.
Measure the resistance between ground and the (V32) S/C Power Supply circuit in
the Brake Switch harness connector.
Is the resistance below 100 ohms?

All

Yes

→ Go To 4

No

→ Repair the short to ground in the (V32) S/C Power Supply circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

4

Turn the ignition off.
Disconnect the Speed Control Servo harness connector.
Disconnect the Brake Switch harness connector.
Measure the resistance between ground and the (V30) S/C Brake Switch Output
circuit at the Speed Control Servo harness connector.
Is the resistance below 100 ohms?

All

Yes

→ Repair the short to ground in the (V30) S/C Brake Switch Output

circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

→ Go To 5

5

Turn the ignition off.
Disconnect the S/C Servo harness connector.
Disconnect the Brake Switch harness connector.
Measure the resistance of the (V30) S/C Brake Switch Output circuit from the Brake
Switch harness connector to the S/C Servo harness connector.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 6

No

→ Repair the open/high resistance in the (V30) S/C Brake Switch

Output circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

234

DRIVEABILITY - NGC

P0594-SPEED CONTROL SERVO POWER CIRCUIT —

Continued

TEST

ACTION

APPLICABILITY

6

Disconnect the Brake Lamp Switch harness connector.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, probe the (V32) Speed Control Power
Supply circuit in the Brake Lamp Switch harness connector.
NOTE: It is necessary to HOLD the Cruise Control Switch in the ON position
to get an accurate reading.
Does the test light illuminate brightly?

All

Yes

→ Replace the Brake Lamp Switch.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

→ Go To 7

7

NOTE: Before continuing, check the PCM harness connector terminals for
corrosion, damage, or terminal push out. Repair as necessary.
If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

235

DRIVEABILITY - NGC

P0594-SPEED CONTROL SERVO POWER CIRCUIT —

Continued

Symptom List:

P0600-SERIAL COMMUNICATION LINK
P0601-INTERNAL MEMORY CHECKSUM INVALID

Test Note:

All symptoms listed above are diagnosed using the same tests.

The title for the tests will be P0600-SERIAL COMMUNICA-
TION LINK.

When Monitored and Set Condition:

P0600-SERIAL COMMUNICATION LINK

When Monitored:

With the ignition on.

Set Condition:

Internal Bus communication failure between the Engine and Transmis-

sion processors.

P0601-INTERNAL MEMORY CHECKSUM INVALID

When Monitored:

With the ignition on.

Set Condition:

Internal checksum for software failed, does not match calculated value.

POSSIBLE CAUSES

PCM INTERNAL OR SPI

TEST

ACTION

APPLICABILITY

1

The Powertrain Control Module is reporting internal errors, view repair to continue.

All

Repair

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

236

DRIVEABILITY - NGC

 

 

 

 

 

 

 

Content   ..  580  581  582  583   ..