Dodge Neon / Neon SRT-4. Manual - part 516

 

  Index      Dodge     Dodge Neon / Neon SRT-4 - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  514  515  516  517   ..

 

 

Dodge Neon / Neon SRT-4. Manual - part 516

 

 

Symptom List:

LEFT FRONT SENSOR CIRCUIT FAILURE
LEFT REAR SENSOR CIRCUIT FAILURE
RIGHT FRONT SENSOR CIRCUIT FAILURE
RIGHT REAR SENSOR CIRCUIT FAILURE

Test Note:

All symptoms listed above are diagnosed using the same tests.

The title for the tests will be LEFT FRONT SENSOR CIRCUIT
FAILURE.

When Monitored and Set Condition:

LEFT FRONT SENSOR CIRCUIT FAILURE

When Monitored:

Ignition on. The CAB monitors the wheel speed circuit continuously.

Set Condition:

If the CAB detects an open or shorted wheel speed sensor circuit, the

Diagnostic Trouble Code (DTC) will set.

LEFT REAR SENSOR CIRCUIT FAILURE

When Monitored:

Ignition on. The CAB monitors the wheel speed circuit continuously.

Set Condition:

If the CAB detects an open or shorted wheel speed sensor circuit, the

Diagnostic Trouble Code (DTC) will set.

RIGHT FRONT SENSOR CIRCUIT FAILURE

When Monitored:

Ignition on. The CAB monitors the wheel speed circuit continuously.

Set Condition:

If the CAB detects an open or shorted wheel speed sensor circuit, the

Diagnostic Trouble Code (DTC) will set.

RIGHT REAR SENSOR CIRCUIT FAILURE

When Monitored:

Ignition on. The CAB monitors the wheel speed circuit continuously.

Set Condition:

If the CAB detects an open or shorted wheel speed sensor circuit, the

Diagnostic Trouble Code (DTC) will set.

POSSIBLE CAUSES

INTERMITTENT CONDITION

WHEEL SPEED SENSOR OR CONNECTOR DAMAGE

WHEEL SPEED SENSOR SIGNAL CIRCUIT FAULT

WHEEL SPEED SENSOR 12 VOLT SUPPLY CIRCUIT SHORT TO GROUND

WHEEL SPEED SENSOR 12 VOLT SUPPLY CIRCUIT OPEN

WHEEL SPEED SENSOR SIGNAL CIRCUIT SHORT TO GROUND

WHEEL SPEED SENSOR SIGNAL CIRCUIT OPEN

16

BRAKES (CAB)

POSSIBLE CAUSES

CAB - 12 VOLT SUPPLY CIRCUIT FAULT

CAB - SIGNAL CIRCUIT FAULT

WHEEL SPEED SENSOR 12 VOLT SUPPLY SHORT TO GROUND

WHEEL SPEED SENSOR SIGNAL CIRCUIT INOPERATIVE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRBIII

t, read DTCs.

With the DRBIII

t, read the Freeze Frame information.

With the DRBIII

t, erase DTCs.

Turn the ignition off.
Turn the ignition on.
With the DRBIII

t, read DTCs.

NOTE: The CAB must sense all four wheels at 25km/h (15 mph) before it will
extinguish the ABS indicators.
Does the DRBIII

t display SENSOR CIRCUIT FAILURE?

All

Yes

→ Go To 2

No

→ Go To 13

2

Turn the ignition off.
Inspect the CAB connector, affected Wheel Speed Sensor, and affected Wheel Speed
Sensor connector.
Is the affected Wheel Speed Sensor or any of the connectors damaged?

All

Yes

→ Repair as necessary.

Perform ABS VERIFICATION TEST - VER 1.

No

→ Go To 3

3

Turn the ignition off.
Disconnect the affected Wheel Speed Sensor connector.
Note: Check connector - Clean/repair as necessary.
Turn the ignition on.
Measure the voltage between affected Wheel Speed Sensor 12 Volt Supply circuit and
ground.
Is the voltage above 10 volts?

All

Yes

→ Go To 6

No

→ Go To 4

4

Turn the ignition off.
Disconnect the CAB harness connector.
Disconnect the affected Wheel Speed Sensor connector.
Using a 12-volt test light connected to 12-volts, probe the affected Wheel Speed
Sensor 12 Volt Supply circuit.
Does the test light illuminate?

All

Yes

→ Repair the affected Wheel Speed Sensor 12 Volt Supply circuit for

a short to ground.
Perform ABS VERIFICATION TEST - VER 1.

No

→ Go To 5

17

BRAKES (CAB)

LEFT FRONT SENSOR CIRCUIT FAILURE —

Continued

TEST

ACTION

APPLICABILITY

5

Turn the ignition off.
Disconnect the CAB harness connector.
Disconnect the affected Wheel Speed Sensor connector.
Connect a jumper wire between affected Wheel Speed Sensor 12 Volt Supply circuit
and ground.
Using a 12-volt test light connected to 12-volts, probe the affected Wheel Speed
Sensor 12 Volt Supply circuit.
Does the test light illuminate?

All

Yes

→ Go To 6

No

→ Repair the affected Wheel Speed Sensor 12 Volt Supply circuit for

an open.
Perform ABS VERIFICATION TEST - VER 1.

6

Turn the ignition off.
Disconnect the affected Wheel Speed Sensor connector.
NOTE: Check connector - Clean/repair as necessary.
Turn the ignition on.
Measure the voltage between affected Wheel Speed Sensor Signal circuit and ground.
Is the voltage above 1 volt?

All

Yes

→ Repair the affected Wheel Speed Sensor Signal circuit for a short

to voltage.
Perform ABS VERIFICATION TEST - VER 1.

No

→ Go To 7

7

Turn the ignition off.
Disconnect the CAB harness connector.
Disconnect the affected Wheel Speed Sensor connector.
Using a 12-volt test light connected to 12-volts, probe the affected Wheel Speed
Sensor Signal circuit.
Does the test light illuminate?

All

Yes

→ Repair the affected Wheel Speed Sensor Signal circuit for a short

to ground.
Perform ABS VERIFICATION TEST - VER 1.

No

→ Go To 8

8

Turn the ignition off.
Disconnect the CAB harness connector.
Disconnect the affected Wheel Speed Sensor connector.
Connect a jumper wire between affected Wheel Speed Sensor Signal circuit and
ground.
Using a 12-volt test light connected to 12-volts, probe the affected Wheel Speed
Sensor Signal circuit.
Does the test light illuminate?

All

Yes

→ Go To 9

No

→ Repair the affected Wheel Speed Sensor Signal circuit for an open.

Perform ABS VERIFICATION TEST - VER 1.

18

BRAKES (CAB)

LEFT FRONT SENSOR CIRCUIT FAILURE —

Continued

TEST

ACTION

APPLICABILITY

9

Turn the ignition off.
Remove the CAB harness strain relief to access wires.
Reconnect the CAB harness connector.
Turn the ignition on.
Measure the voltage between affected Wheel Speed Sensor 12 Volt Supply circuit and
ground.
Is the voltage above 10 volts?

All

Yes

→ Go To 10

No

→ Replace the Controller Antilock Brake in accordance with the

Service Information.
Perform ABS VERIFICATION TEST - VER 1.

10

Turn the ignition off.
Remove the CAB harness strain relief to access wires.
Reconnect the CAB harness connector.
Turn the ignition on.
Measure the voltage between affected Wheel Speed Sensor 12 Volt Supply circuit and
affected Wheel Speed Sensor Signal circuit.
Is the voltage above 10 volts?

All

Yes

→ Go To 11

No

→ Replace the Controller Antilock Brake in accordance with the

Service Information.
Perform ABS VERIFICATION TEST - VER 1.

11

Turn the ignition off.
Reconnect ALL affected Wheel Speed Sensor circuit connectors.
Disconnect the affected Wheel Speed Sensor connector.
Turn the ignition on.
Measure the voltage of the affected Wheel Speed Sensor 12 Volt Supply circuit in the
affected Wheel Speed Sensor connector while reconnecting the sensor connector.
Did the affected Wheel Speed Sensor 12 Volt Supply circuit drop voltage to 0 DC
volts?

All

Yes

→ Replace the affected Wheel Speed Sensor in accordance with the

Service Information.
Perform ABS VERIFICATION TEST - VER 1.

No

→ Go To 12

12

Turn the ignition off.
Reconnect ALL affected Wheel Speed Sensor circuit connectors.
Turn the ignition on.
Measure the DC voltage of the Wheel Speed Sensor Signal circuit in the affected
Wheel Speed Sensor connector.
Slowly rotate the wheel.
Does the DC voltage toggle between 1.6 volts to .8 volts?

All

Yes

→ Go To 13

No

→ Replace the affected Wheel Speed Sensor in accordance with the

Service Information.
Perform ABS VERIFICATION TEST - VER 1.

19

BRAKES (CAB)

LEFT FRONT SENSOR CIRCUIT FAILURE —

Continued

 

 

 

 

 

 

 

Content   ..  514  515  516  517   ..