Dodge Neon / Neon SRT-4. Manual - part 477

 

  Index      Dodge     Dodge Neon / Neon SRT-4 - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  475  476  477  478   ..

 

 

Dodge Neon / Neon SRT-4. Manual - part 477

 

 

Symptom:

*COMPASS/TEMPERATURE MIRROR INOPERATIVE

POSSIBLE CAUSES

NO RESPONSE - PCI BUS - COMPASS

FUSED B(+) CIRCUIT SHORT TO GROUND

FUSED B(+) CIRCUIT OPEN

FUSED IGNITION SWITCH OUTPUT CIRCUIT SHORT TO GROUND

FUSED IGNITION SWITCH OUTPUT CIRCUIT OPEN

GROUND CIRCUIT OPEN

COMPASS/TEMPERATURE MIRROR

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRBIII

t, attempt to I/D or communicate with the Compass/Temperature

Mirror.
Was the DRBIII

t able to communicate with the Compass/Temperature Mirror.

All

Yes

→ Go To 2

No

→ Refer to Communications for the related symptom(s).

Perform BODY VERIFICATION TEST - VER 1.

2

Turn the ignition off.
Remove and inspect the #4 Fuse in the Fuse Block.
If the fuse is open, replace with the proper rated fuse.
Turn the ignition on for approximately 1 minute.
Turn the ignition off.
Remove and inspect the #4 Fuse in the Fuse Block.
Is the #4 Fuse open?

All

Yes

→ Check the Fused B(+) circuit for a short to ground and repair as

necessary. If the Fused B(+) circuit is not shorted to ground,
replace the Compass/Temperature Mirror.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 3

3

Turn the ignition off.
Remove and inspect the #7 Fuse in the Fuse Block.
If the fuse is open, replace with the proper rated fuse.
Turn the ignition on for approximately 1 minute.
Turn the ignition off.
Remove and inspect the #7 Fuse in the Fuse Block.
Is the #7 Fuse open?

All

Yes

→ Check the Fused Ignition Switch Output circuit for a short to

ground and repair as necessary. If the Fused Ignition Switch
Output circuit is not shorted to ground, replace the Compass/
Temperature Mirror.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 4

130

COMPASS/MINI-TRIP COMPUTER

TEST

ACTION

APPLICABILITY

4

Turn the ignition off.
Disconnect the Compass/Temperature Mirror harness connector.
Measure the voltage between the Fused B(+) circuit and ground.
Is the voltage below 10.5 volts?

All

Yes

→ Repair the Fused B(+) circuit for an open.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 5

5

Turn the ignition off.
Disconnect the Compass/Temperature Mirror harness connector.
Turn the ignition on.
Measure the voltage between the Fused Ignition Switch Output circuit and ground.
Is the voltage below 10.5 volts?

All

Yes

→ Repair the Fused Ignition Switch Output circuit for an open.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 6

6

Turn the ignition off.
Disconnect the Compass/Temperature Mirror harness connector.
Measure the resistance between ground and the Compass/Temperature Mirror
Ground circuit.
Is the resistance above 5.0 ohms?

All

Yes

→ Repair the Ground circuit for an open.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Replace the Compass/Temperature Mirror in accordance with the

Service Information.
Perform BODY VERIFICATION TEST - VER 1.

131

COMPASS/MINI-TRIP COMPUTER

*COMPASS/TEMPERATURE MIRROR INOPERATIVE —

Continued

Symptom:

*TEMPERATURE DISPLAY INOPERATIVE OR WRONG (2.0L ONLY)

POSSIBLE CAUSES

DTC PRESENT IN PCM

AMBIENT TEMPERATURE SENSOR

COMPASS/TEMPERATURE MIRROR

TEST

ACTION

APPLICABILITY

1

With the DRBIII

t, read DTCs.

Does the DRBIII

t display any PCM Ambient Temp DTCs?

All

Yes

→ Refer to DRIVEABILITY for the related symptom(s).

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 2

2

Turn the ignition off.
Disconnect the Ambient Temperature Sensor harness connector.
Measure the Ambient Temperature Sensor using the following values:
10°C (50°F) Sensor Resistance = 17.99 - 21.81 Kilohms
20°C (68°F) Sensor Resistance = 11.37 - 13.61 Kilohms
25°C (77°F) Sensor Resistance = 9.12 - 10.88 Kilohms
30°C (86°F) Sensor Resistance = 7.37 - 8.75 Kilohms
40°C (104°F) Sensor Resistance = 4.90 - 5.75 Kilohms
50°C (122°F) Sensor Resistance = 3.33 - 3.88 Kilohms
Does the Ambient Temperature Sensor resistance measure between the min/max
specifications?

All

Yes

→ Replace the Compass/Temp Mirror in accordance with the Service

Information.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Replace the Ambient Temperature Sensor in accordance with the

Service Information.
Perform BODY VERIFICATION TEST - VER 1.

132

COMPASS/MINI-TRIP COMPUTER

Symptom:

*HIGH BEAM HEADLAMPS WILL NOT TRN ON

POSSIBLE CAUSES

OPEN FUSED B+

DIMMER SWITCH LOW BEAM OUTPUT CIRCUIT SHORT TO GROUND

DIMMER SWITCH HIGH BEAM OUTPUT CIRCUIT SHORT TO GROUND

OPEN FUSE

DIMMER SWITCH LOW BEAM OUTPUT CIRCUIT OPEN

INSTRUMENT CLUSTER

MULTIFUNCTION SWITCH

TEST

ACTION

APPLICABILITY

1

Remove Circuit Breaker 2 from the Fuse Block.
Measure voltage of the Fused B+ circuit at the Circuit Breaker connector.
Is the voltage above 10.0 volts?

All

Yes

→ Go To 2

No

→ Repair the open Fused B+ circuit from Fuse Block fuse 15.

Perform BODY VERIFICATION TEST - VER 1.

2

Check fuse 15 in the Fuse Block.
Is fuse 15 open?

All

Yes

→ Go To 3

No

→ Go To 5

3

Remove fuse 15 from the Fuse Block.
Disconnect the Multifunction Switch connector.
Measure resistance of the Dimmer Switch Low Beam Output Circuit to ground.
Is the resistance below 5.0 ohms?

All

Yes

→ Repair the Dimmer Switch Low Beam Output Circuit for a short

to ground condition.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 4

4

Remove Circuit Breaker 2 from the Fuse Block.
Disconnect the Multifunction Switch connector.
Measure resistance of the Dimmer Switch High Beam Output Circuit and ground.
Is the resistance below 5.0 ohms?

All

Yes

→ Repair the Dimmer Switch High Beam Output Circuit for a short

to ground condition.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 5

133

EXTERIOR LIGHTING

 

 

 

 

 

 

 

Content   ..  475  476  477  478   ..