Dodge Nitro. Manual - part 634

 

  Index      Dodge     Dodge Nitro - service repair manual 2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  632  633  634  635   ..

 

 

Dodge Nitro. Manual - part 634

 

 

1) TEST FOR INTERMITTENT CONDITION 

Turn the ignition on. 

With the scan tool, clear all DTC's 

Turn the Left Turn Signal on. 

With the scan tool, read DTC's. 

Does the scan tool display active: B17BF-LEFT SIDEMARKER LAMP CONTROL CIRCUIT 
OVERCURRENT?
  

Yes  

Go to 2).  

No  

The condition that caused this symptom is currently not present. Check for an intermittent 
condition by inspecting the related wiring harness for chafed, pierced, pinched, and partially broken 
wires. Also, inspect the related connectors for broken, bent, pushed out, spread, corroded, or 
contaminated terminals. Repair as necessary.  

Perform BODY VERIFICATION TEST - VER 1 .  

2) LEFT REAR TURN SIGNAL BULB 

Turn the ignition off. 

Remove Left Rear Turn Signal Bulb. 

Inspect the Left Rear Turn Signal Bulb. 

Is the inoperative bulb OK?  

Yes  

Go to 3).  

No  

Replace the Inoperative bulb in accordance with the Service Information.  

Perform BODY VERIFICATION TEST - VER 1 .  

3) (L163) LEFT SIDEMARKER LAMP CONTROL CIRCUIT SHORT TO GROUND 

Disconnect the TIPM C4 harness connector.

 

2007 Dodge Nitro R/T 

2007 ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Electrical/Diagnostics - Nitro

  

Disconnect the Left Sidemarker Lamp harness connector.

Measure the resistance between ground and the (L163) Left Sidemarker Lamp Control circuit. 

Is the resistance above 10k ohms?  

Yes  

Go to 4).  

No  

Repair the (L163) Left Sidemarker Lamp Control circuit for a short to ground.  

Perform BODY VERIFICATION TEST - VER 1 .  

4) (L163) LEFT SIDEMARKER LAMP CONTROL CIRCUIT SHORTED TO VOLTAGE 

Turn the ignition on. 

Measure for voltage on the (L163) Left Sidemarker Lamp Control circuit. 

Is there any voltage present?  

Yes  

Repair the (L163) Left Sidemarker Lamp Control circuit short to voltage.  

Perform BODY VERIFICATION TEST - VER 1 .  

No  

Replace the Totally Integrated Power Module (TIPM) in accordance with the Service Information.  

Perform BODY VERIFICATION TEST - VER 1 .  

B17C2-RIGHT SIDEMARKER LAMP CONTROL CIRCUIT HIGH 

For complete wiring diagrams refer to SYSTEM WIRING DIAGRAMS article. 

When Monitored: 

Continuously. 

Set Condition: 

When the Totally Integrated Power Module (TIPM) detects a HIGH condition. 

Possible Causes 

 

2007 Dodge Nitro R/T 

2007 ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Electrical/Diagnostics - Nitro

  

Diagnostic Test 

1) TEST FOR INTERMITTENT CONDITION 

Turn the ignition on. 

With the scan tool, clear all DTC's 

Turn the Right Turn Signal on. 

With the scan tool, read DTC's. 

Does the scan tool display active: B17C2-RIGHT SIDEMARKER LAMP CONTROL CIRCUIT 
HIGH?
  

Yes  

Go to 2).  

No  

The condition that caused this symptom is currently not present. Check for an intermittent 
condition by inspecting the related wiring harness for chafed, pierced, pinched, and partially broken 
wires. Also, inspect the related connectors for broken, bent, pushed out, spread, corroded, or 
contaminated terminals. Repair as necessary.  

Perform BODY VERIFICATION TEST - VER 1 .  

2) RIGHT REAR TURN SIGNAL BULB 

Turn the ignition off. 

Remove Right Rear Turn Signal Bulb. 

Inspect the Right Rear Turn Signal Bulb. 

Is the inoperative bulb OK?  

Yes  

Go to 3).  

No  

(L162) RIGHT SIDEMARKER LAMP CONTROL CIRCUIT OPEN
(L162) RIGHT SIDEMARKER LAMP CONTROL CIRCUIT SHORTED TO VOLTAGE
TOTALLY INTEGRATED POWER MODULE

 

2007 Dodge Nitro R/T 

2007 ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Electrical/Diagnostics - Nitro

  

Replace the Inoperative bulb in accordance with the Service Information.  

Perform BODY VERIFICATION TEST - VER 1 .  

3) (L162) RIGHT SIDEMARKER LAMP CONTROL CIRCUIT OPEN 

Disconnect the TIPM C4 harness connector. 

Disconnect the Right Sidemarker Lamp assembly harness connector. 

Measure the resistance of the (L162) Right Sidemarker Lamp Control circuit between the Right 
Sidemarker Lamp assembly harness connector and the TIPM C4 harness connector. 

Does the ohm meter read open circuit?  

Yes  

Repair the (L162) Right Sidemarker Lamp Control circuit for an open.  

Perform BODY VERIFICATION TEST - VER 1 .  

No  

Go to 4).  

4) (L162) RIGHT SIDEMARKER LAMP CONTROL CIRCUIT SHORTED TO VOLTAGE 

Turn the ignition on. 

Measure for voltage on the (L162) Right Sidemarker Lamp Control circuit. 

Is there any voltage present?  

Yes  

Repair the (L162) Right Sidemarker Lamp Control circuit short to voltage.  

Perform BODY VERIFICATION TEST - VER 1 .  

No  

Replace the Totally Integrated Power Module (TIPM) in accordance with the Service Information.  

Perform BODY VERIFICATION TEST - VER 1 .  

B17C4-RIGHT SIDEMARKER LAMP CONTROL CIRCUIT OVERCURRENT 

For complete wiring diagrams refer to SYSTEM WIRING DIAGRAMS article. 

When Monitored: 

 

2007 Dodge Nitro R/T 

2007 ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Electrical/Diagnostics - Nitro

  

 

 

 

 

 

 

 

Content   ..  632  633  634  635   ..