Dodge Nitro. Manual - part 626

No  

Go to 5).  

5) (L54) RIGHT STOP LAMP CONTROL CIRCUIT OPEN 

Turn the ignition off. 

Disconnect the TIPM C7 connector. 

Measure the resistance of the (L54) Right Stop Lamp Control circuit between the Right Rear Tail Lamp 
harness connector and the TIPM C7 harness connector. 

Is the resistance below 10.0 ohms?  

No  

Go to 6).  

Yes  

Repair the (L54) Right Stop Lamp Control circuit for an open.  

Perform BODY VERIFICATION TEST - VER 1 .  

6) (L54) RIGHT STOP LAMP CONTROL CIRCUIT SHORTED TO VOLTAGE 

Turn the ignition on. 

Measure the voltage between (L54) Right Stop Lamp Control circuit and ground. 

Is there any voltage present?  

Yes  

Repair the (L54) Right Stop Lamp Control circuit for a short to voltage.  

Perform BODY VERIFICATION TEST - VER 1 .  

No  

Replace the Totally Integrated Power Module (TIPM) in accordance with the Service Information.  

Perform BODY VERIFICATION TEST - VER 1 .  

B1647-REAR RIGHT TURN CONTROL CIRCUIT LOW 

For complete wiring diagrams refer to SYSTEM WIRING DIAGRAMS article. 

When Monitored: 

 

2007 Dodge Nitro R/T 

2007 ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Electrical/Diagnostics - Nitro

  

With the Turn Signal activated. 

Set Condition: 

When the Totally Integrated Power Module (TIPM) detects a LOW condition. 

Diagnostic Test 

1) INTERMITTENT CONDITION 

Turn the ignition on. 

With the scan tool, clear all DTC's. 

Turn the Right Turn Signal on. 

With the scan tool, read DTC's. 

Does the scan tool display active: B1647-REAR RIGHT TURN LAMP CONTROL CIRCUIT 
LOW?  

Yes  

Go to 2).  

No  

The condition that caused this symptom is currently not present. Check for an intermittent 
condition by inspecting the related wiring harness for chafed, pierced, pinched, and partially broken 
wires. Also, inspect the related connectors for broken, bent, pushed out, spread, corroded, or 
contaminated terminals. Repair as necessary.  

Perform BODY VERIFICATION TEST - VER 1 .  

2) REAR RIGHT TURN SIGNAL BULB 

Turn the ignition off. 

Disconnect the Right Rear Turn Signal Bulb. 

Turn the ignition on. 

With the scan tool, read DTC's. 

Possible Causes 

(L62) RIGHT REAR TURN SIGNAL CONTROL CIRCUIT SHORT TO GROUND
RIGHT REAR TURN SIGNAL BULB
TOTALLY INTEGRATED POWER MODULE

 

2007 Dodge Nitro R/T 

2007 ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Electrical/Diagnostics - Nitro

  

Does the DTC reset?  

Yes  

Go to 3).  

No  

Replace the Right Rear Turn Signal Bulb in accordance with the Service Information.  

Perform BODY VERIFICATION TEST - VER 1 .  

3) (L62) RIGHT REAR TURN SIGNAL CONTROL CIRCUIT SHORT TO GROUND 

Turn the ignition off. 

Disconnect the TIPM C7 harness connector. 

Disconnect the Right Rear Tail Lamp harness connector. 

Measure the resistance between ground and the (L62) Right Rear Turn Signal Control circuit. 

Is the resistance above 10k ohms?  

Yes  

Replace the Totally Integrated Power Module (TIPM) in accordance with the Service Information.  

Perform BODY VERIFICATION TEST - VER 1 .  

No  

Repair the (L62) Right Rear Turn Signal Control circuit for a short to ground.  

Perform BODY VERIFICATION TEST - VER 1 .  

B1648-REAR RIGHT TURN CONTROL CIRCUIT HIGH 

For complete wiring diagrams refer to SYSTEM WIRING DIAGRAMS article. 

When Monitored: 

Continuously. 

Set Condition: 

When the Totally Integrated Power Module (TIPM) detects a HIGH condition. 

Possible Causes 

 

2007 Dodge Nitro R/T 

2007 ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Electrical/Diagnostics - Nitro

  

Diagnostic Test 

1) TEST FOR INTERMITTENT CONDITION 

Turn the ignition on. 

With the scan tool, clear all DTC's. 

Turn the Right Turn Signal on. 

With the scan tool, read DTC's. 

Does the scan tool display active: B1648-REAR RIGHT TURN LAMP CONTROL CIRCUIT 
HIGH?  

Yes  

Go to 2).  

No  

The condition that caused this symptom is currently not present. Check for an intermittent 
condition by inspecting the related wiring harness for chafed, pierced, pinched, and partially broken 
wires. Also, inspect the related connectors for broken, bent, pushed out, spread, corroded, or 
contaminated terminals. Repair as necessary.  

Perform BODY VERIFICATION TEST - VER 1 .  

2) CHECK (Z910) GROUND CIRCUITS 

Turn the ignition off. 

Disconnect the Right Rear Turn Signal Lamp assembly harness connector. 

With a 12-volt test light connected to 12-volts, probe each (Z910) Ground circuit. 

Does the test light illuminate brightly on each ground circuit?  

Yes  

Go to 4).  

CHECK (Z910) GROUND CIRCUIT
(Z910) GROUND CIRCUIT OPEN
CHECK (L62) RIGHT REAR TURN SIGNAL CONTROL CIRCUIT
(L62) RIGHT REAR TURN SIGNAL CONTROL CIRCUIT OPEN
(L62) RIGHT REAR TURN SIGNAL CONTROL CIRCUIT SHORTED TO VOLTAGE
TOTALLY INTEGRATED POWER MODULE

 

2007 Dodge Nitro R/T 

2007 ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Electrical/Diagnostics - Nitro