DAF CF65, CF75, CF85 Series . Manual - part 941

©

 200423

5-7

Front axle and leading rear axle

TECHNICAL DATA

ΧΦ65/75/85 series

7

0

186N front axle toe, configured as a single front 

axle or second front axle in the case of two 

steered front axles

1

2

3

4

5

7

8

9

0

-1

0,5

-0,5

-1,5

1,5

2,5

3,5

4,5

5,5

-2

2

3

4

5

6

1

mm/m

186 N

x 1000 KG

S7 00 902

6

TECHNICAL DATA

5-8

©

 200423

Front axle and leading rear axle

0

ΧΦ65/75/85 series

7

186N front axle toe, configured as a first front axle 

in the case of two steered front axles

Alignment of steerable axles
Deviation in driving direction of the wheel of the 

second front axle or leading rear axle in relation 

to the front axle wheel:

Measured on the left-hand wheels on an 

LHD vehicle.

Measured on the right-hand wheels on an 

RHD vehicle.

1

2

3

4

5

6

7

8

9

0

-1

0,5

-0,5

-1,5

1,5

2,5

3,5

4,5

5,5

-2

2

3

4

5

6

1

mm/m

186 N

x 1000 KG

S7 00 903

A
A

S700138

-

check value

≥ 3 mm/m (angles A)

-

setting value

≥ 1 mm/m (angles A)

©

 200423

5-9

Front axle and leading rear axle

TECHNICAL DATA

ΧΦ65/75/85 series

7

0

Check values for toe-out

Single front axle:
Front axle

Wheel base

Wheel 1

Wheel 2

150N

 4.40 m

30



25



150N

> 4.40 m

30



25



152N

 4.40 m

30



25



152N

> 4.40 m

30



26



156N

 4.40 m

30



25



156N

> 4.40 m

30



26



182N

 4.50 m

30



25



182N

> 4.50 m

30



26



186N

 4.50 m

30



25



186N

> 4.50 m

30



26



A 1

 tolerance applies to the distortion of wheel 2

Dual front axle/leading rear axle:
Type

Wheel base

Wheel 1

Wheel 2

Wheel 3

Wheel 4

FTG

3.82 m

30



25



12



9



FAG

4.10 m

30



25



12



9



FAG

4.60 m

30



26



10



8



FAG

5.20 m

30



26



8



7



FAG

5.75 m

30



26



8



7



FAG

6.50 m

30



26



7



6



FAD/FAC/FAL

4.30 m

30



26



21



19



FAX

4.60 m

30



26



21



19



FAD/FAC/FAX/FAL

5.00 m

30



26



21



19



FAD/FAC/FAX/FAL

5.70 m

30



26



22



20



FAD/FAC/FAX/FAL

6.40 m

30



26



24



21



FAD/FAC/FAL

7.10 m

30



26



24



21



A 1

 tolerance applies to the distortion of wheels 2, 3 and 4.

S7 00 124

1

3

4

2

TECHNICAL DATA

5-10

©

 200423

Front axle and leading rear axle

0

ΧΦ65/75/85 series

7

Angle of idler arm FAC/FAD/FAX/FAL

Angle of idler arms FAG/FTG

Permitted tolerance, steering box input shaft
Test with steering gear in the central position.

Permitted tolerance of the input shaft of the 

steering box relative to the marking: 20

.

Steering ball joints

Swivel axle

A

S7 00 706

Angle A:

90



A

C

B

S700708

Angle A:

90



Angle B:

90



Angle C:

20

 ≥ 1.5

S7 00 860

Axial play

maximum 1.5 mm

Axial play

0.05 - 0.3 mm

Overview of shim thickness for adjustment of 

swivel axle pay

1.50 mm

1.75 mm

1.88 mm

2.00 mm

2.13 mm

2.25 mm

2.38 mm