DAF CF65, CF75, CF85 Series . Manual - part 54

©

1-3

ECAS-3 fault codes

ECAS-3

DAVIE XD diagnostics manual 

13

41-43

Value outside range on pin 7 of the ECU, height 
sensor right, driven axle (F613)

-

No chassis height control

-

Normal driving level function does not work

41-44

Short circuit to supply or open connection on pin 
7 of the ECU, height sensor right, driven axle 
(F613)

-

No chassis height control, rear right

42-41

Short circuit to earth on pin 6 of the ECU, height 
sensor, front axle (F614)

-

No chassis height control, front axle

42-43

Value outside range on pin 6 of the ECU, height 
sensor, front axle (F614)

-

No chassis height control

-

Normal driving level function does not work

42-44

Short circuit to supply or open connection on pin 
6 of the ECU, height sensor, front axle (F614)

-

No chassis height control, front axle

55-42

Short circuit to supply or open connection on pin 
12 of the ECU, speed signal

-

No chassis height control

-

ECAS responds immediately to height level 
changes (unstable handling)

Fault code

Fault code description with possible cause

System response

ECAS-3

1-4

©

ECAS-3 fault codes

13

DAVIE XD diagnostics manual

©

2-1

ECAS-3 customer parameters

ECAS-3

DAVIE XD diagnostics manual 

13

2. ECAS-3 CUSTOMER PARAMETERS

2.1 INTRODUCTION

Customer parameters
Customer parameters are the settings of an 

electronic system. The customer parameters 

permit adapting control functions of a system to 

the customer's particular wishes and/or needs 

within certain limits. The customer parameters 

are stored in a list in the memory of the electronic 

unit. Customer parameters can be modified using 

the programming feature of DAVIE XD. 

Programming using DAVIE XD is only possible if 

the logged-in user has been registered as a 

"Master Technician".

Note:

Erroneous settings of customer parameters may 

affect the action of control functions to such an 

extent that they function eratically or not at all. 

After modification of the settings the (modified) 

customer parameters must be stored in the 

electronic unit using the programming function in 

the customer parameter overview.

Customer parameter names and codes
Each customer parameter in a system has its 

own name and code. The following explanation of 

the customer parameters includes only the 

codes. The availability of a customer parameter 

in a system depends on the programmed 

software in the electronic unit. The programmed 

software depends on the vehicle configuration/

identity card data.

Standard values
Standard values, options and setting ranges may 

vary according to the software variants of 

DAVIE XD and the system. This is why they have 

not been included in the following explanation of 

the customer parameters.

ECAS-3

2-2

©

ECAS-3 customer parameters

DAVIE XD diagnostics manual

13

2.2

E

X

P

LANATORY

 NOTES

 TO ECAS-3

 CUSTOME

R

 PARAME

TERS

ECAS

-3 

c

u

sto

m

er

 

para

meter

 c

o

de

Exp

la

n

atio

n

D

e

p

en

de

nc

es:

Notes

Minimum 

va

lu

e to be

 

se

t:

Ma

ximum 

value

 to

 b

e 

set:

4

-0

1

Wi

th

 thi

s 

p

arameter the protection

 fo

r e

m

p

ty be

llow

s ca

n 

be

 swi

tche

d on or off.

When

 the

 p

rote

cti

on is switched off, there is no resid

ual

 

pressure in the air be

llow

s so that 

'p

leating

' of 

the

 

bell

ows is 

n

o long

er prevented

.

4

-0

2

T

his parameter makes it 

po

ssible

 to increa

se th

e 

tolera

nce fi

eld (hysteresis) 

of the

 sen

sor se

nsitivity.

Thi

s 

is a

 solu

tion 

if a 

cu

sto

m

e

r compla

ins a

bou

t unstabl

e 

re

gul

ati

on by ECAS-3. If a larg

er 

tol

erance

 fiel

d is 

ch

osen, th

e heig

ht 

cha

nge

 o

f th

e chassis must be

 

increase

d to al

low ECAS 

to make a correction.

4

-0

3

T

his parameter ena

ble

s a certain

 veh

icle slan

t to be 

redu

ced or increa

se

d.

Redu

ctio

n ma

kes 

the

 veh

icle stand stra

igh

te

r (if 

the

 

ca

libra

tion is correct, i.e

. the

 sa

me hei

ght left and ri

ght).

Incre

ase will

 make the vehi

cle slant fu

rth

er, thereb

y 

enab

ling

 u

nstable

 h

orizontal

 setting

s 

to 

be 

preve

nte

d.

4

-0

4

T

he time of th

e de

lay setti

ng can

 be le

ngthe

ned w

ith

 th

is 

par

a

meter.

4

-0

5

T

his parameter rela

tes to 

th

e 

storag

e of 

faul

ts in the 

el

ectro

nic unit on the action of admitting ai

r to or 

exha

usting 

ai

r 

from the

 ai

r b

ello

ws.

A 

fa

ult is i

den

tifie

d if the

 hei

ght sen

sor read

ing

 doe

s not 

ch

ang

e d

uring

 the

 p

ro

grammed 

time 

whil

e i

t shou

ld 

have do

ne becau

se of 

the de

sired action

. Th

is 

time can

 

be lengthened with this 

pa

rameter. The 

ECAS system 

the

n waits long

er 

b

efore sto

ring the fa

ult becau

se 

the

 

heig

ht 

sen

sor 

re

adin

g has not ch

ang

ed.