DAF 95XF. Manual - part 201

 

  Index      DAF     DAF 95XF Series - service repair manual

 

Search            

 

 

 

 

 

 

 

  

 

Content   ..  199  200  201  202   ..

 

 

DAF 95XF. Manual - part 201

 

 

©

 200438

1-1

EBS-2 fault codes

EBS-2

DAVIE XD diagnostics manual 

12

1. EBS-2 FAULT CODES

1.1 INTRODUCTION

If the electronic unit detects a system fault, this 

fault is usually stored in the memory of the 

electronic unit as a fault code.

Most system faults will also generate a warning.

EBS-2

1-2

©

 200438

EBS-2 fault codes

12

DAVIE XD diagnostics manual

1.2 EXPLANATORY NOTES TO EBS-2 FAULT CODES

If there is an electrical fault in the EBS system, 

the symptom "open circuit in EBS pressure 

control" or "deactivation of EBS pressure control" 

may occur as a system reaction.

Open circuit in EBS pressure control
On application of the foot brake valve, the 

electronic unit will receive information on the 

desired vehicle deceleration from the brake pedal 

position sensor in the foot brake valve.

In the electronic unit, this vehicle deceleration 

command is converted into brake pressure to the 

brake cylinders.

If there is no feedback from the output pressure 

or wheel speed, there will be less accurate 

electronically controlled deceleration and brake 

force distribution.

Deactivation of EBS pressure control
The output pressure control in the brake cylinders 

is entirely pneumatic; i.e. there is no more 

electronically controlled deceleration and brake 

force distribution.

Fault code

Fault code description with possible cause

Symptom

11-18

Voltage on pin A8 of the EBS unit is too low due 
to:
-

contact resistance or poor connection to pin 
A8 of the EBS unit

-

ABS on front axle deactivated

-

ASR brake control deactivated

-

EBS pressure control on front axle and 
drawn vehicle deactivated

-

VSC system deactivated

11-31

Extremely low voltage (<3 V) on pin A8 of the 
EBS unit due to:
-

excessive contact resistance on pin A8 of 
the EBS unit

-

interruption on pin A8 of the EBS unit 

-

ABS on front axle deactivated

-

ASR brake control deactivated

-

EBS pressure control on front axle and 
drawn vehicle deactivated

-

VSC system deactivated

12-18

Voltage on pin A9 of the EBS unit is too low due 
to:
-

contact resistance or poor connection to pin 
A9 of the EBS unit

-

short circuit to earth on pin B7 of the EBS 
unit

-

ABS on front and rear axles deactivated

-

ASR brake/engine control deactivated

-

EBS pressure control on rear axle 
deactivated

-

VSC system deactivated

12-31

Extremely low voltage (<3 V) on pin A9 of the 
EBS unit due to:
-

excessive contact resistance on pin A9 of 
the EBS unit

-

interruption on pin A9 of the EBS unit 

-

ABS on front and rear axles deactivated

-

ASR brake/engine control deactivated

-

EBS pressure control on rear axle 
deactivated

-

VSC system deactivated

Short circuit to earth on pin E4 or B7 of the EBS 
unit

-

ABS on front and rear axles deactivated

-

ASR brake/engine control deactivated

-

EBS pressure control on rear axle 
deactivated

-

Pin B7 is internally switched to earth in the 
ECU and in addition the power supply to A9 
and E4 is switched off internally.

-

VSC system deactivated

©

 200438

1-3

EBS-2 fault codes

EBS-2

DAVIE XD diagnostics manual 

12

13-18

Voltage on pin A7 of the EBS unit is too low due 
to:
-

contact resistance or poor connection to pin 
A7 of the EBS unit

-

interruption on pin A7 of the EBS unit 

-

No noticeable system limitation in EBS

14-32

Sensor supply voltage on pins D9, B13 or E1 of 
the EBS unit due is too low due to:
-

contact resistance or poor connection on 
specified connection points of the EBS unit

-

short circuit to earth on specified connection 
points of the EBS unit

-

VSC system deactivated

14-33

Constant voltage, even if the ignition is turned off 
and the brake is not applied, on pin D9, B13 or E1 
of the EBS unit due to:
-

short circuit to supply on specified 
connection points of the EBS unit

-

VSC system deactivated

15-33

Constant voltage, even if the ignition is turned off 
and the brake is not applied, on pin B7 of the EBS 
unit due to:
-

short circuit to supply on pin B7 of the EBS 
unit

-

No noticeable system limitation in EBS

16-11

Internal fault in EBS unit

-

ABS on front and rear axles deactivated

-

ASR brake/engine control deactivated

-

EBS pressure control on front axle, rear axle 
and drawn vehicle deactivated

-

VSC system deactivated

16-12

Configuration parameters in the EBS unit 
incorrect due to:
-

incorrect programming

-

retrofitted components without identification 
card (oxford) change

-

ABS on front and rear axles deactivated

-

ASR brake/engine control deactivated

-

EBS pressure control on front axle, rear axle 
and drawn vehicle deactivated

-

VSC system deactivated

16-15

Internal fault in EBS unit

-

ABS on front and rear axles deactivated

-

ASR brake/engine control deactivated

-

EBS pressure control on front axle, rear axle 
and drawn vehicle deactivated

-

VSC system deactivated

16-17

Voltage (>32 V) on pins A7, A8 and A9 of the EBS 
unit is too high due to:
-

excessive alternator/battery voltage

-

inductive voltage of external component

-

ABS on front and rear axles deactivated

-

ASR brake/engine control deactivated

-

EBS pressure control on front axle, rear axle 
and drawn vehicle deactivated

-

VSC system deactivated

16-18

Voltage on pins A7, A8 and A9 of the EBS unit at 
a speed of >2 km/h is too low due to:
-

insufficient battery voltage

-

poor earth connection to EBS unit

-

ABS on front and rear axles deactivated

-

ASR brake/engine control deactivated

-

EBS pressure control on front axle, rear axle 
and drawn vehicle deactivated

-

VSC system deactivated

16-49

Unacceptable information from steering angle 
sensor (F701) due to:
-

incorrect mechanical adjustment of straight-
ahead position of steering gear

-

VSC system deactivated

Fault code

Fault code description with possible cause

Symptom

EBS-2

1-4

©

 200438

EBS-2 fault codes

12

DAVIE XD diagnostics manual

16-53

The difference in peripheral speed between the 
left and right wheel on the same axle exceeds 
10%

-

ABS on front and rear axles deactivated

-

ASR brake/engine control deactivated

-

VSC system deactivated

17-32

Voltage on pin B15 of the EBS unit at least 2.5 V 
lower than the voltage on pin A8 of the EBS unit 
due to:
-

short circuit to earth on pin B15 of the EBS 
unit

-

VSC system deactivated

17-33

When the ignition is switched on, voltage is 
already supplied to pin B15 of the EBS unit due 
to:
-

short circuit to supply on pin B15 of the EBS 
unit

-

VSC system deactivated

21-37

Interruption on pin C4 and/or C5 of the EBS unit, 
wheel speed sensor (F513)

-

ABS on front axle, right deactivated

-

ASR brake/engine control deactivated

-

VSC system deactivated

21-38

Unacceptable wheel speed sensor frequency 
signal from wheel speed sensor (F513) on pins 
C4 and C5 of the EBS unit due to:
-

loose pole ring

-

wrong assessment by EBS unit

-

ABS on front and rear axles deactivated

-

ASR brake/engine control deactivated

-

EBS pressure control on front axle, rear axle 
and drawn vehicle deactivated

-

VSC system deactivated

21-41

Short circuit to earth on pin C4 and/or C5 of the 
EBS unit, wheel speed sensor (F513)

-

ABS on front axle, right deactivated

-

ASR brake/engine control deactivated

-

VSC system deactivated

21-42

Short circuit to supply on pin C4 and/or C5 of the 
EBS unit, wheel speed sensor (F513)

-

ABS on front axle, right deactivated

-

ASR brake/engine control deactivated

-

VSC system deactivated

21-44

Short circuit on pin C4 and/or C5 of the EBS unit, 
wheel speed sensor (F513)

-

ABS on front axle, right deactivated

-

ASR brake/engine control deactivated

-

VSC system deactivated

21-45

Incorrect wheel speed sensor sine-wave signal 
from wheel speed sensor (F513) on pins C4 and 
C5 of the EBS unit due to:
-

distorted wheel speed sensor ring

-

damaged wheel speed sensor ring

-

ABS on front axle, right deactivated

-

ASR brake/engine control deactivated

-

VSC system deactivated

21-46

No uniformity (frequency changes) of wheel 
speed sensor signal from wheel speed sensor 
(F513) on pins C4 and C5 of the EBS unit due to:
-

heavy point due to brake disc wobble, for 
example

-

ABS on front axle, right deactivated

-

ASR brake/engine control deactivated

-

VSC system deactivated

21-47

Excessive oscillation of wheel speed sensor 
signal (maximum/minimum level) from wheel 
speed sensor (F513) on pins C4 and C5 of the 
EBS unit due to:
-

excessive wheel bearing play

-

incorrect mounting of wheel speed sensor 
ring

-

ABS on front axle, right deactivated

-

ASR brake/engine control deactivated

-

VSC system deactivated

Fault code

Fault code description with possible cause

Symptom

 

 

 

 

 

 

 

Content   ..  199  200  201  202   ..