Chrysler Town, Dodge Caravan. Manual - part 997

 

  Index      Chrysler     Chrysler TOWN & COUNTRY, VOYAGER, Dodge Caravan - service repair manual 2001-2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  995  996  997  998   ..

 

 

Chrysler Town, Dodge Caravan. Manual - part 997

 

 

Symptom:

P0218-HIGH TEMPERATURE OPERATION ACTIVATED

When Monitored and Set Condition:

P0218-HIGH TEMPERATURE OPERATION ACTIVATED

When Monitored:

Whenever the engine is running.

Set Condition:

Immediately when the Overheat shift schedule is activated when the

Transmission Oil Temperature reaches 116 °C or 240 °F.

POSSIBLE CAUSES

ENGINE COOLING SYSTEM MALFUNCTION

TRANSMISSION OIL COOLER PLUGGED

HIGH TEMPERATURE OPERATIONS ACTIVATED

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many Transmission problems. If
the fluid level is low locate and repair the leak then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read the engine DTC’s. Check and repair all engine DTC’s prior

to performing Transmission Symptom Diagnostics.
With the DRBIII

t, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.

NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

All

Continue

Go To

2

24

TRANSMISSION - EATX

TEST

ACTION

APPLICABILITY

2

This DTC is an informational DTC designed to aid the Technician in diagnosing shift
quality complaints.
This DTC indicates that the Transmission has been operating in the

9Overheat9 shift

schedule which may generate a customer complaint.
The customer driving patterns may indicate the need for an additional Transmission
Oil Cooler.
With the DRBIII

t, check the EATX EVENT DATA to help identify the conditions in

which the DTC was set.
Were there any problems found?

All

Yes

→ Repair the cause of the Transmission Overheating per the Service

Information. If indicated install an additional Transmission Oil
Cooler.
Perform 41TE TRANSMISSION VERIFICATION TEST - VER 1.

No

→ Go To 3

3

Perform Engine Cooling System diagnostics per the Service Information
Is the Engine Cooling System functioning properly?

All

Yes

→ Go To 4

No

→ Repair the cause of the Engine Overheating. Refer to the Service

Information for additional repair information.
Perform 41TE TRANSMISSION VERIFICATION TEST - VER 1.

4

If there are no possible causes remaining, view repair.

All

Repair

Flush or replace the Transmission Oil cooler as necessary per the
Service Information.
Perform 41TE TRANSMISSION VERIFICATION TEST - VER 1.

25

TRANSMISSION - EATX

P0218-HIGH TEMPERATURE OPERATION ACTIVATED —

Continued

Symptom:

P0562-LOW BATTERY VOLTAGE

When Monitored and Set Condition:

P0562-LOW BATTERY VOLTAGE

When Monitored:

With the engine running and the TCM has closed the Transmission

Control Relay.

Set Condition:

If battery voltage at TCM Transmission Control Relay Output Sense

circuit is less than 10.0 volts for 15 seconds. *This DTC generally indicates a gradually
falling battery voltage or resistive connections to the TCM.

POSSIBLE CAUSES

RELATED CHARGING SYSTEM DTCS

FUSED B+ CIRCUIT OPEN OR HIGH RESISTANCE

GROUND CIRCUIT OPEN OR HIGH RESISTANCE

TRANSMISSION CONTROL RELAY OUTPUT CIRCUIT TO TCM OPEN OR HIGH RESISTANCE

TRANSMISSION CONTROL RELAY

TRANSMISSION CONTROL MODULE

INTERMITTENT WIRING AND CONNECTORS

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many Transmission problems. If
the fluid level is low locate and repair the leak then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read the engine DTC’s. Check and repair all engine DTC’s prior

to performing Transmission Symptom Diagnostics.
With the DRBIII

t, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.

NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

All

Continue

Go To

2

26

TRANSMISSION - EATX

TEST

ACTION

APPLICABILITY

2

With the DRBIII

t, read the PCM DTC’s.

Are there any Charging System related DTC’s stored in the PCM?

All

Yes

→ Refer to the Charging System category and repair any PCM

Charging System DTC’s first. NOTE: After repairing the PCM
charging system DTC’s, perform the Transmission Verification
test to verify the transmission was not damaged.
Perform 41TE TRANSMISSION VERIFICATION TEST - VER 1.

No

→ Go To 3

3

NOTE: Generator, battery, and charging system must be fully functional
before performing this test.
With the DRBIII

t, read Transmission DTC’s.

With the DRBIII

t, Check the STARTS SINCE SET counter for P0562.

Note: This counter only applies to the last DTC set.
Is the Starts Since Set counter for P0562 set at 0?

All

Yes

→ Go To 4

No

→ Go To 9

4

Turn the ignition off to the lock position.
Disconnect the TCM harness connector.
Note: Check connectors - Clean/repair as necessary.
Using a 12-volt test light connected to 12-volts, check the ground circuits in the TCM
harness connector.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly for all the ground circuits?

All

Yes

→ Go To 5

No

→ Repair the Ground circuit(s) for an open or high resistance.

Perform 41TE TRANSMISSION VERIFICATION TEST - VER 1.

5

Turn the ignition off to the lock position.
Disconnect the TCM harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output in the Transmission Control Relay connector.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, check the Fused B+ circuit in the TCM
harness connector.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?

All

Yes

→ Go To 6

No

→ Repair the Fused B+ circuit for an open or high resistance. If the

fuse is open make sure to check for a short to ground.
Perform 41TE TRANSMISSION VERIFICATION TEST - VER 1.

27

TRANSMISSION - EATX

P0562-LOW BATTERY VOLTAGE —

Continued

 

 

 

 

 

 

 

Content   ..  995  996  997  998   ..