Chrysler Town, Dodge Caravan. Manual - part 918

 

  Index      Chrysler     Chrysler TOWN & COUNTRY, VOYAGER, Dodge Caravan - service repair manual 2001-2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  916  917  918  919   ..

 

 

Chrysler Town, Dodge Caravan. Manual - part 918

 

 

Symptom:

INCOMPLETE POWER OPEN - VOLTAGE BELOW MINIMUM
LEVEL

When Monitored and Set Condition:

INCOMPLETE POWER OPEN - VOLTAGE BELOW MINIMUM LEVEL

When Monitored:

Whenever the power sliding door is performing a power open operation.

Set Condition:

The PSD Module detects that the voltage is below 9.5 volts during the

power open operation.

POSSIBLE CAUSES

DTC PRESENT

MODULE VOLTAGE LOW

BINDING SLIDING DOOR

DRB OPERATING VOLTAGE LOW

POWER SLIDING DOOR MODULE - HIGH RESISTANCE

POWER SLIDING DOOR MOTOR

TEST

ACTION

APPLICABILITY

1

With the DRBIII

t, record and erase DTC’s.

Turn the ignition off, wait 10 seconds, then turn the ignition on.
Operate the power sliding door several times if possible.
With the DRBIII

t, read DTCs.

Does the DRBIII

t display INCOMPLETE POWER OPEN - VOLTAGE BELOW

MINIMUM LEVEL?

All

Yes

→ Go To 2

No

→ Using the wiring diagram/schematic as a guide, inspect the

wiring and connectors for an intermittent condition. Operate the
door several times and check for any binding conditions.
Perform BODY VERIFICATION TEST - VER 1.

2

Examine the door for proper fit and alignment, loose/ hard or torn seals, worn teeth
on the track and gear (lower drive unit) or anything that would cause an obstruction
to proper operation.
Manually operate the other sliding door or of a known good vehicle and notice the
effort needed to open and close.
Compare the effort needed on the disabled door.
Does it take more effort to operate the sliding door than it should?

All

Yes

→ Refer to Service information for the related symptom(s).

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 3

908

POWER DOORS - SLIDING

TEST

ACTION

APPLICABILITY

3

NOTE: Test the battery to ensure it is fully charged and in good condition
before proceeding.
Turn the ignition off.
Turn all lights and accessories off.
With the DRBIII

t in 9Sliding Door9 9Monitor Display9 9PCI Bus Info9 read the

9Battery Voltage9 and compare it to the 9PSD Bat Volts Input9.
NOTE: If the difference is greater than 0.5 volts, backprobe the Fused B(+)
at the module to verify.
Does the voltage vary more than 0.5 volts?

All

Yes

→ Using the wiring diagram/schematic as a guide, inspect the

wiring and connectors. Locate and repair the reason for the
voltage drop.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 4

4

Turn the ignition off.
Turn all lights and accessories off.
With the DRBIII

t in 9Sliding Door9 9Monitor Display9 9PCI Bus Info9 read the

9Battery Voltage9 and compare it to the 9PSD Bat Volts Input9.
Operate the power sliding door and observe the voltage difference.
NOTE: If the difference is greater than 1.6 volts, backprobe the Fused B(+)
at the module to verify.
Does the voltage vary more than 1.6 volts when the liftgate is operating??

All

Yes

→ Using the wiring diagram/schematic as a guide, inspect the

wiring and connectors. Locate and repair the reason for the
voltage drop.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 5

5

Turn the ignition off.
Turn all lights and accessories off.
Remove the sliding door trim panel to gain access to the Power Sliding Door Module.
Backprobe voltmeter leads between the Fused B(+) and the Sliding Door Open Driver
circuits in the PSD C1 connector.
Close the sliding door.
Operate the power sliding door in the OPEN position and observe the voltage
difference.
Does the voltage vary more than 0.2 volts when the sliding door is opening?

All

Yes

→ Replace the Power Sliding Door Module.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 6

6

If there are no possible causes remaining, view repair.

All

Repair

Check the wiring and connections from the module to the motor
for high resistance. If the wiring is okay, replace the Power Sliding
Door Motor assembly.
Perform BODY VERIFICATION TEST - VER 1.

909

POWER DOORS - SLIDING

INCOMPLETE POWER OPEN - VOLTAGE BELOW MINIMUM LEVEL —

Continued

Symptom:

IOD WAKE UP OPEN - PSD

When Monitored and Set Condition:

IOD WAKE UP OPEN - PSD

When Monitored:

Anytime the Body Control Module is awake.

Set Condition:

If the BCM does not sense a signal circuit from the Sliding Door Module

this code will set.

POSSIBLE CAUSES

DTC PRESENT

BODY CONTROL MODULE - IOD WAKE UP OPEN

SLIDING DOOR WAKE UP SIGNAL WIRE OPEN

LIFTGATE MODULE WAKE UP SIGNAL WIRE SHORT TO GROUND

SLIDING DOOR WAKE UP SIGNAL WIRE SHORT TO GROUND

SLIDING DOOR MODULE - IOD WAKE UP OPEN

TEST

ACTION

APPLICABILITY

1

With the DRBIII

t, record and erase DTC’s.

Turn the ignition off, wait 10 seconds, then turn the ignition on.
Wait 10 seconds.
With the DRBIII

t, read DTCs.

Does the DRBIII

t display IOD WAKE UP OPEN?

All

Yes

→ Go To 2

No

→ Using the wiring diagram/schematic as a guide, inspect the

wiring and connectors for an intermittent condition.
Perform BODY VERIFICATION TEST - VER 1.

2

Disconnect the BCM C3 connector.
Measure the voltage between the appropriate Sliding Door Wake Up Signal circuit
and ground.
Is the voltage above 10.0 volts?

All

Yes

→ Replace the Body Control Module.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 3

910

POWER DOORS - SLIDING

TEST

ACTION

APPLICABILITY

3

Disconnect the Body Control Module C3 connector.
Disconnect the appropriate Sliding Door Control Module C2 connector.
Measure the resistance of the appropriate Sliding Door Wake Up Signal circuit
between the BCM C3 connector and the Sliding Door Control Module C2 connector.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 4

No

→ Repair the appropriate Sliding Door Wake Up Signal wire for an

open.
Perform BODY VERIFICATION TEST - VER 1.

4

Disconnect the Body Control Module C2 connector.
Disconnect the Power Liftgate Module C2 connector.
Measure the resistance between the Liftgate Module Wake Up Signal circuit and
ground.
Is the resistance below 100.0 ohms?

All

Yes

→ Repair the Liftgate Module Wake Up Signal wire for a short to

ground.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 5

5

NOTE: If this vehicle is equipped with 2 power sliding doors, this test must
be repeated for each door.
Disconnect the Body Control Module C3 connector.
Disconnect the appropriate Sliding Door Control Module C2 connector.
Measure the resistance between the appropriate Sliding Door Wake Up Signal circuit
and ground.
Is the resistance below 100.0 ohms?

All

Yes

→ Repair the appropriate Sliding Door Wake Up Signal wire for a

short to ground.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 6

6

If there are no possible causes remaining, view repair.

All

Repair

Replace the Sliding Door Module.
Perform BODY VERIFICATION TEST - VER 1.

911

POWER DOORS - SLIDING

IOD WAKE UP OPEN - PSD —

Continued

 

 

 

 

 

 

 

Content   ..  916  917  918  919   ..