Chrysler Town, Dodge Caravan. Manual - part 897

 

  Index      Chrysler     Chrysler TOWN & COUNTRY, VOYAGER, Dodge Caravan - service repair manual 2001-2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  895  896  897  898   ..

 

 

Chrysler Town, Dodge Caravan. Manual - part 897

 

 

TEST

ACTION

APPLICABILITY

7

Turn the ignition off.
Disconnect the Power Liftgate Module C2 connector.
Measure the resistance between ground and the Liftgate Gear Engage Driver circuit.
Wiggle the harness and check for an intermittent short condition.
Is the resistance below 1000.0 ohms?

All

Yes

→ Repair the Liftgate Gear Engage Driver circuit for a short to

ground.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 8

8

Turn the ignition off.
Disconnect the Power Liftgate Module C2 connector.
Measure the resistance between the Ground circuit (cavity 20) and the Liftgate Gear
Engage Driver circuit.
Wiggle the harness and check for an intermittent short condition.
Is the resistance below 1000.0 ohms?

All

Yes

→ Repair the Liftgate Gear Engage Driver circuit for a short to the

Ground circuit.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 9

9

Ensure all module and motor connectors are connected at this time.
Try to operate the liftgate in the close position.
Did the motor start to close the liftgate but was very slow and labored extensively?

All

Yes

→ Replace the Power Liftgate Motor assembly.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Replace the Power Liftgate Module

Perform BODY VERIFICATION TEST - VER 1.

824

POWER DOORS - LIFTGATE

INCOMPLETE POWER CLOSE - OVER CURRENT —

Continued

Symptom:

INCOMPLETE POWER CLOSE - TRANSISTOR SHORTED

When Monitored and Set Condition:

INCOMPLETE POWER CLOSE - TRANSISTOR SHORTED

When Monitored:

Whenever the power liftgate is performing a power close operation.

Set Condition:

The Power Liftgate Module detects that the motor is rotating (monitors

hall effect pulses) even though the controlled PWM rate is 0 percent. This DTC is set
during the power close (2 second chime period, prior to movement of the liftgate) operation.

POSSIBLE CAUSES

DTC PRESENT

POWER LIFTGATE MODULE

TEST

ACTION

APPLICABILITY

1

With the DRBIII

t, record and erase DTC’s.

Turn the ignition off, wait 10 seconds, then turn the ignition on.
Operate the power liftgate several times if possible.
With the DRBIII

t, read ACTIVE DTCs.

Does the DRBIII

t display INCOMPLETE POWER CLOSE - TRANSISTOR

SHORTED?

All

Yes

→ Replace the Power Liftgate Module.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Using the wiring diagram/schematic as a guide, inspect the

wiring and connectors for an intermittent condition. Operate the
liftgate several times and check for any binding conditions.
Perform BODY VERIFICATION TEST - VER 1.

825

POWER DOORS - LIFTGATE

Symptom:

INCOMPLETE POWER CLOSE - VOLTAGE BELOW MINIMUM
LEVEL

When Monitored and Set Condition:

INCOMPLETE POWER CLOSE - VOLTAGE BELOW MINIMUM LEVEL

When Monitored:

Whenever the power liftgate is performing a power close operation.

Set Condition:

The PLG Module detects that the voltage is below 9.5 volts during the

power close operation.

POSSIBLE CAUSES

DTC PRESENT

MODULE VOLTAGE LOW

BINDING LIFTGATE

DRB OPERATING VOLTAGE LOW

PLG MODULE - HIGH RESISTANCE

POWER LIFTGATE MOTOR

TEST

ACTION

APPLICABILITY

1

With the DRBIII

t, record and erase DTC’s.

Turn the ignition off, wait 10 seconds, then turn the ignition on.
Operate the power liftgate several times if possible.
With the DRBIII

t, read DTCs.

Does the DRBIII

t display INCOMPLETE POWER CLOSE - VOLTAGE BELOW

MINIMUM LEVEL?

All

Yes

→ Go To 2

No

→ Using the wiring diagram/schematic as a guide, inspect the

wiring and connectors for an intermittent condition. Operate the
door several times and check for any binding conditions.
Perform BODY VERIFICATION TEST - VER 1.

2

Examine the liftgate for proper fit and alignment, or anything that would cause an
obstruction to proper operation.
Check the prop rods to ensure liftgate will fall closed from the approximately 3/4
closed position.
Does it take more effort to operate the liftgate than it should?

All

Yes

→ Refer to Service information for the related symptom(s).

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 3

826

POWER DOORS - LIFTGATE

TEST

ACTION

APPLICABILITY

3

NOTE: Test the battery to ensure it is fully charged and in good condition
before proceeding.
Turn the ignition off.
Turn all lights and accessories off.
With the DRBIII

t in 9Power Liftgate9 9Monitor Display9 9PCI Bus Info9 read the

9Battery Voltage9 and compare it to the 9PLG Bat Volts Input9.
NOTE: If the difference is greater than 0.5 volts, backprobe the Fused B(+)
at the module to verify.
Does the voltage vary more than 0.5 volts?

All

Yes

→ Using the wiring diagram/schematic as a guide, inspect the

wiring and connectors. Locate and repair the reason for the
voltage drop.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 4

4

Turn the ignition off.
Turn all lights and accessories off.
With the DRBIII

t in 9Power Liftgate99 9Monitor Display9 9PCI Bus Info9 read the

9Battery Voltage9 and compare it to the 9PLG Bat Volts Input9.
Operate the power liftgate and observe the voltage difference.
NOTE: If the difference is greater than 1.6 volts, backprobe the Fused B(+)
at the module to verify.
Does the voltage vary more than 1.6 volts when the liftgate is operating??

All

Yes

→ Using the wiring diagram/schematic as a guide, inspect the

wiring and connectors. Locate and repair the reason for the
voltage drop.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 5

5

Turn the ignition off.
Turn all lights and accessories off.
Open the Liftgate.
Remove the left rear trim panel to gain access to the Power Liftgate Module.
Remove the PLG module but leave it connected.
Backprobe voltmeter leads between the Fused B(+) and the Liftgate Close Driver
circuits in the PLG C1 connector.
Operate the power liftgate in the CLOSED position and observe the voltage
difference.
Does the voltage vary more than 0.2 volts when the liftgate is operating??

All

Yes

→ Replace the Power Liftgate Module.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 6

6

If there are no possible causes remaining, view repair.

All

Repair

Check the wiring and connections from the module to the motor
for high resistance. If the wiring is okay, replace the Power
Liftgate Motor assembly.
Perform BODY VERIFICATION TEST - VER 1.

827

POWER DOORS - LIFTGATE

INCOMPLETE POWER CLOSE - VOLTAGE BELOW MINIMUM LEVEL —

Continued

 

 

 

 

 

 

 

Content   ..  895  896  897  898   ..