Chrysler Town, Dodge Caravan. Manual - part 879

 

  Index      Chrysler     Chrysler TOWN & COUNTRY, VOYAGER, Dodge Caravan - service repair manual 2001-2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  877  878  879  880   ..

 

 

Chrysler Town, Dodge Caravan. Manual - part 879

 

 

TEST

ACTION

APPLICABILITY

4

Turn the ignition off.
Disconnect the Ambient Temperature Sensor harness connector.
Check connectors - Clean/repair as necessary.
Measure the resistance of the Ambient Temperature Sensor.
0°C (32°F) Sensor Resistance = 29.33 - 35.99 kilohms
10°C (50°F) Sensor Resistance = 17.99 - 21.81 kilohms
20°C (68°F) Sensor Resistance = 11.37 - 13.61 kilohms
30°C (86°F) Sensor Resistance = 7.37 - 8.75 kilohms
40°C (104°F) Sensor Resistance = 4.90 - 5.75 kilohms
Does the Ambient Temperature Sensor measure within specifications?

All

Yes

→ Go To 5

No

→ Replace the Ambient Temperature Sensor in accordance with the

Service Information.
Perform BODY VERIFICATION TEST - VER 1.

5

Turn the ignition off.
Disconnect the Ambient Temperature Sensor harness connector.
Disconnect the IPM C1 harness connector.
Check connectors - Clean/repair as necessary.
Measure the resistance of the Ambient Temperature Sensor Signal circuit to the
Sensor Return circuit.
Does the resistance measure less than 5.0 ohms?

All

Yes

→ Repair the Ambient Temperature Sensor Signal circuit for a short

to the Sensor Return circuit.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 6

6

Turn the ignition off.
Disconnect the Ambient Temperature Sensor harness connector.
Disconnect the IPM C1 harness connector.
Check connectors - Clean/repair as necessary.
Measure the resistance of the Ambient Temperature Sensor Signal circuit to ground.
Does the resistance measure less than 5.0 ohms?

All

Yes

→ Repair the Ambient Temperature Sensor Signal circuit for a short

to ground.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 7

7

Turn the ignition off.
Disconnect the Ambient Temperature Sensor harness connector.
Disconnect the IPM C1 harness connector.
Check connectors - Clean/repair as necessary.
Measure the resistance of the Ambient Temperature Sensor Signal circuit.
Does the resistance measure less than 5.0 ohms?

All

Yes

→ Go To 8

No

→ Repair the Ambient Temperature Sensor Signal circuit for an

open.
Perform BODY VERIFICATION TEST - VER 1.

752

OVERHEAD CONSOLE

*REPAIRING CMTC DISPLAYS DOUBLE DASH ( - - ) IN TEMP DISPLAY

Continued

TEST

ACTION

APPLICABILITY

8

Turn the ignition off.
Disconnect the Ambient Temperature Sensor harness connector.
Disconnect the IPM C1 harness connector.
Check connectors - Clean/repair as necessary.
Measure the resistance of the Ambient Temperature Sensor Return circuit.
Does the resistance measure less than 5.0 ohms?

All

Yes

→ Go To 9

No

→ Repair the Ambient Temperature Sensor Return circuit for an

open.
Perform BODY VERIFICATION TEST - VER 1.

9

Turn the ignition off.
Disconnect and isolate the battery negative cable.
Disconnect the IPM C1 harness connector.
Disconnect the FCM from the IPM.
Check connectors - Clean/repair as necessary.
Measure the resistance of the Ambient Temperature Sensor Signal circuit and the
Return circuit through the IPM.
Does each circuit resistance measure less than 5.0 ohms?

All

Yes

→ Replace the Front Control Module in accordance with the Service

Information.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Replace the Intelligent Power Module in accordance with the

Service Information.
Perform BODY VERIFICATION TEST - VER 1.

753

OVERHEAD CONSOLE

*REPAIRING CMTC DISPLAYS DOUBLE DASH ( - - ) IN TEMP DISPLAY

Continued

Symptom:

DRIVER DOOR LOCK SWITCH INPUT OPEN OR SHORT TO VOLT-
AGE

When Monitored and Set Condition:

DRIVER DOOR LOCK SWITCH INPUT OPEN OR SHORT TO VOLTAGE

When Monitored:

At all times when battery power is supplied to the Body Control

Module.

Set Condition:

When the BCM senses voltage to the door lock switch above 4.6 volts for

over 10 seconds.

POSSIBLE CAUSES

DTC PRESENT

BODY CONTROL MODULE - DRIVER DOOR LOCK SWITCH VOLTAGE LOW

DOOR LOCK SWITCH GROUND OPEN

DOOR LOCK SWITCH MUX CIRCUIT OPEN

DOOR LOCK SWITCH OPEN

DOOR LOCK SWITCH MUX CIRCUIT SHORT TO VOLTAGE

BODY CONTROL MODULE - DOOR LOCK SWITCH MUX SHORT TO VOLTAGE

TEST

ACTION

APPLICABILITY

1

With the DRBIII

t, record and erase DTC’s.

Cycle the ignition switch from ON to OFF to ON.
With the DRBIII

t, read DTC’s.

Remove the key and operate the door locks from the Driver Door Lock Switch while
monitoring the DRBIII

t.

Wait 10 seconds.
Does the DRBIII

t display DR DOOR LOCK SW INPUT OPEN OR SHORT TO

VOLTAGE?

All

Yes

→ Go To 2

No

→ Using the wiring diagram/schematic as a guide, inspect the

wiring and connectors.
Perform BODY VERIFICATION TEST - VER 1.

2

With the DRBIII

t in Sensors, read the DR DOOR LOCK SW voltage.

Does the DRBIII

t display 4.3 volts or greater?

All

Yes

→ Go To 3

No

→ Disconnect the BCM harness connector(s). Check connectors -

Clean/repair as necessary. If okay, replace the Body Control
Module.
Perform BODY VERIFICATION TEST - VER 1.

754

POWER DOOR LOCKS/RKE

TEST

ACTION

APPLICABILITY

3

Disconnect the Driver Door Lock Switch connector.
Using a 12-volt test light connected to 12-volts, check the Ground circuit in the
harness connector.
Does the test light illuminate brightly?

All

Yes

→ Go To 4

No

→ Repair the Ground circuit for an open.

Perform BODY VERIFICATION TEST - VER 1.

4

Disconnect the Driver Door Lock Switch connector.
Measure the voltage between Door Lock Switch Mux circuit and Ground in the
harness connector.
Select the voltage present.

All

Below 4.3 volts..

Repair the Door Lock Switch Mux circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.

Between 4.4 volts and 5.2 volts.

Replace the Door Lock Switch.
Perform BODY VERIFICATION TEST - VER 1.

Above 5.3 volts.

Go To

5

5

Disconnect the Driver Door Lock Switch connector.
Disconnect the Body Control Module C3 connector.
NOTE: Check connectors - Clean/repair as necessary.
Turn the ignition on.
Turn the park lamps on.
Measure the voltage between Door Lock Switch Mux circuit and ground.
Is there any voltage present?

All

Yes

→ Repair the Door Lock Switch Mux circuit for a short to voltage.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Replace the Body Control Module.

Perform BODY VERIFICATION TEST - VER 1.

755

POWER DOOR LOCKS/RKE

DRIVER DOOR LOCK SWITCH INPUT OPEN OR SHORT TO VOLTAGE —

Continued

 

 

 

 

 

 

 

Content   ..  877  878  879  880   ..