Chrysler Town, Dodge Caravan. Manual - part 866

 

  Index      Chrysler     Chrysler TOWN & COUNTRY, VOYAGER, Dodge Caravan - service repair manual 2001-2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  864  865  866  867   ..

 

 

Chrysler Town, Dodge Caravan. Manual - part 866

 

 

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Disconnect the Memory Seat Mirror Module C1 connector.
Disconnect the Left Power Mirror connector.
Measure the resistance of the Left Mirror Vertical Position Signal circuit to ground
at the Left Power Mirror harness side connector.
Is the resistance below 1000.0 ohms?

All

Yes

→ Repair the Left Mirror Vertical Position Signal wire for a short to

ground.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.

No

→ Replace the Memory Seat Mirror Module.

Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.

700

MEMORY SEAT

LEFT MIRROR VERTICAL SENSOR OUT OF RANGE LOW —

Continued

Symptom:

MEMORY POSITION SWITCH STUCK

When Monitored and Set Condition:

MEMORY POSITION SWITCH STUCK

When Monitored:

Anytime the Body Control Module is awake.

Set Condition:

If the Memory switch is active for over 10 seconds.

POSSIBLE CAUSES

DTC PRESENT

MEMORY SET SWITCH STUCK

MEMORY SELECT SWITCH MUX SHORT TO GROUND

BODY CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

With the DRBIII

t, record and erase DTC’s.

Cycle the ignition OFF then back ON.
With the DRBIII

t, read DTCs.

Operate the Memory Set switch several times while monitoring the DRBIII.
Does the DRBIII

t display MEMORY SWITCH INPUT STUCK?

All

Yes

→ Go To 2

No

→ Using the wiring diagram/schematic as a guide, inspect the

wiring and connectors for an intermittent condition.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.

2

Disconnect the Memory Set Switch connector
Turn the ignition on.
With the DRBIII

t in Sensors, read the Memory Select SW Volts.

Is the voltage above 4.8 volts?

All

Yes

→ Replace the Memory Set Switch.

Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.

No

→ Go To 3

3

Turn the ignition off.
Disconnect the Memory Set switch connector.
Disconnect the BCM C1 harness connector.
Measure the resistance between ground and the Memory Select Switch MUX circuit.
Is the resistance above 1000.0 ohms?

All

Yes

→ Go To 4

No

→ Repair the Memory Select Switch MUX circuit for a short to

ground.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.

701

MEMORY SEAT

TEST

ACTION

APPLICABILITY

4

If there are no possible causes remaining, view repair.

All

Repair

Replace the Body Control Module.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.

702

MEMORY SEAT

MEMORY POSITION SWITCH STUCK —

Continued

Symptom:

MEMORY SWITCH INPUT OPEN

When Monitored and Set Condition:

MEMORY SWITCH INPUT OPEN

When Monitored:

Continuously when the PCI bus is active.

Set Condition:

If the Memory Set switch voltage is greater than 4.8 volts for over 10

seconds.

POSSIBLE CAUSES

DTC PRESENT

MEMORY SET SWITCH OPEN

MEMORY SELECT SWITCH MUX OPEN

MEMORY SELECT SWITCH RETURN OPEN

BODY CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

With the DRBIII

t, record and erase DTC’s.

Cycle the ignition OFF then back ON.
With the DRBIII

t, read DTCs.

Operate the Memory Set switch several times while monitoring the DRBIII.
Does the DRBIII

t display MEMORY SWITCH INPUT OPEN?

All

Yes

→ Go To 2

No

→ Using the wiring diagram/schematic as a guide, inspect the

wiring and connectors for an intermittent condition.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.

2

Disconnect the Memory Set Switch connector
Turn the ignition on.
Connect a jumper wire between Memory Select Switch MUX and Memory Select
Switch Return.
With the DRBIII

t in Sensors, read the Memory Select SW Volts.

Is the voltage below 1.0 volt?

All

Yes

→ Replace the Memory Set Switch.

Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.

No

→ Go To 3

703

MEMORY SEAT

 

 

 

 

 

 

 

Content   ..  864  865  866  867   ..