Chrysler Town, Dodge Caravan. Manual - part 831

 

  Index      Chrysler     Chrysler TOWN & COUNTRY, VOYAGER, Dodge Caravan - service repair manual 2001-2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  829  830  831  832   ..

 

 

Chrysler Town, Dodge Caravan. Manual - part 831

 

 

Symptom:

*BLEND/MODE/RECIRC DOOR OPERATION IMPROPER -- DUAL &
THREE-ZONE MTC

POSSIBLE CAUSES

CHECK FOR ACTIVE HVAC DTCS

CHECK FOR HVAC DO0R RECALIBRATION FAULT MESSAGES

MODE DOOR ACTUATOR/LINKAGE/DOOR

PASSENGER BLEND DOOR ACTUATOR/LINKAGE/DOOR

DRIVER BLEND DOOR ACTUATOR/LINKAGE/DOOR

RECIRCULATION DOOR ACTUATOR/LINKAGE/DOOR

REAR MODE DOOR ACTUATOR/LINKAGE/DOOR

REAR BLEND DOOR ACTUATOR/LINKAGE/DOOR

TEST

ACTION

APPLICABILITY

1

NOTE: All Actuator Circuit Test fault messages and Overcurrent DTCs must
be repaired before diagnosing Calibration fault messages.
Turn the ignition on.
With the DRBIII

t, read active HVAC DTCs.

Does the DRBIII

t display any active HVAC DTCs?

All

Yes

→ Return to the symptom list and choose the symptom(s).

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 2

2

NOTE: All Actuator Circuit Test fault messages and Overcurrent DTCs must
be repaired before diagnosing Calibration fault messages.
Turn the ignition on.
With the DRBIII

t in HVAC, System Tests, actuate the HVAC Door Recalibration

Test.
Does the DRBIII

t display any HVAC Door Recalibration fault messages?

All

Yes

→ Return to the symptom list and choose the symptom(s).

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 3

560

HEATING & A/C

TEST

ACTION

APPLICABILITY

3

Which door did customer ID as faulty?

All

Mode Door

Go To

4

Passenger Blend Door

Go To

5

Driver Blend Door

Go To

6

Recirculation Door

Go To

7

Rear Mode Door

Go To

8

Rear Blend Door

Go To

9

4

Start the engine.
Turn the blower control to the high speed position.
Turn the mode control to each door position for a minimum of 30 seconds and check
for airflow from the corresponding vents.
Does air flow from the correct vents for each door position?

All

Yes

→ Test Complete.

No

→ Remove door actuator from A/C Heater Housing Assy. By hand,

attempt to rotate door actuator in both directions. Also, inspect for
disconnected, missing, or broken door actuator linkage. Repair as
necessary in accordance with the Service Information.
Perform BODY VERIFICATION TEST - VER 1.

5

Start the engine.
Turn the blower control to the high speed position.
Turn the mode control to the panel position.
Move the passenger blend control to the full hot position.
Move the passenger blend control to the full cold position, in 25% increments, while
checking for a change in airflow air temperature coming from the passenger’s panel
vents.
Does the airflow air temperature change with respect to the position of the blend
control?

All

Yes

→ Test Complete.

No

→ Remove door actuator from A/C-Heater Housing Assy. By hand,

attempt to rotate the door actuator in both directions. Also,
inspect for disconnected, missing, or broken door actuator link-
age. Repair as necessary in accordance with the Service Informa-
tion.
Perform BODY VERIFICATION TEST - VER 1.

561

HEATING & A/C

*BLEND/MODE/RECIRC DOOR OPERATION IMPROPER -- DUAL &
THREE-ZONE MTC —

Continued

TEST

ACTION

APPLICABILITY

6

Start the engine.
Turn the blower control to the high speed position.
Turn the mode control to the panel position.
Move the driver blend control to the full hot position.
Move the driver blend control to the full cold position, in 25% increments, while
checking for a change in airflow air temperature coming from the driver’s panel
vents.
Does the airflow air temperature change with respect to the position of the blend
control?

All

Yes

→ Test Complete.

No

→ Remove door actuator from A/C-Heater Housing Assy. By hand,

attempt to rotate the door actuator in both directions. Also,
inspect for disconnected, missing, or broken door actuator link-
age. Repair as necessary in accordance with the Service Informa-
tion.
Perform BODY VERIFICATION TEST - VER 1.

7

Start the engine.
Turn the blower control to the high speed position.
Turn the mode control to the panel position.
Make sure that recirc is switched off (status indicator not illuminated).
Press the recirc switch on (status indicator illuminated). The sound of the air flowing
through the ducts should get louder as the recirculation door opens to bring in recirc
air.
Does the sound of the airflow get louder after pressing the recirc switch on?

All

Yes

→ Test Complete.

No

→ Remove door actuator from A/C-Heater Housing Assy. By hand,

attempt to rotate the door actuator in both directions. Also,
inspect for disconnected, missing, or broken door actuator link-
age. Repair as necessary in accordance with the Service Informa-
tion.
Perform BODY VERIFICATION TEST - VER 1.

8

Start the engine.
Turn the rear blower control on the A/C-Heater Control Module to the rear control
position.
Turn the rear blower control on the Rear A/C-Heater Control to the high speed
position.
Turn the rear blend control to the full cold position and check for airflow from the
corresponding vents.
Turn the rear blend control to the full hot position and check for airflow from the
corresponding vents.
Does air flow from the correct vents for each door position?

All

Yes

→ Test Complete.

No

→ Remove door actuator from Rear A/C-Heater Housing Assy. By

hand, attempt to rotate door actuator in both directions. Also,
inspect for disconnected, missing, or broken door actuator link-
age. Repair as necessary in accordance with the Service Informa-
tion.
Perform BODY VERIFICATION TEST - VER 1.

562

HEATING & A/C

*BLEND/MODE/RECIRC DOOR OPERATION IMPROPER -- DUAL &
THREE-ZONE MTC —

Continued

TEST

ACTION

APPLICABILITY

9

Start the engine.
Turn the rear blower control on the A/C-Heater Control Module to the rear control
position.
Turn the rear blower control on the Rear A/C-Heater Control to the high speed
position.
Turn the rear blend control to the full cold position.
Turn the rear blend control to the full hot position, in 25% increments, while checking
for a change in airflow air temperature coming from the vents.
Does the airflow air temperature change with respect to the position of the blend
control?

All

Yes

→ Test Complete.

No

→ Remove door actuator from Rear A/C-Heater Housing Assy. By

hand, attempt to rotate door actuator in both directions. Also,
inspect for disconnected, missing, or broken door actuator link-
age. Repair as necessary in accordance with the Service Informa-
tion.
Perform BODY VERIFICATION TEST - VER 1.

563

HEATING & A/C

*BLEND/MODE/RECIRC DOOR OPERATION IMPROPER -- DUAL &
THREE-ZONE MTC —

Continued

 

 

 

 

 

 

 

Content   ..  829  830  831  832   ..