Chrysler Town, Dodge Caravan. Manual - part 800

 

  Index      Chrysler     Chrysler TOWN & COUNTRY, VOYAGER, Dodge Caravan - service repair manual 2001-2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  798  799  800  801   ..

 

 

Chrysler Town, Dodge Caravan. Manual - part 800

 

 

Symptom:

EBL RUN ONLY RELAY OPEN

When Monitored and Set Condition:

EBL RUN ONLY RELAY OPEN

When Monitored:

Continuously with the ignition on.

Set Condition:

The FCM has detected an open in the Rear Defogger Relay control circuit.

POSSIBLE CAUSES

OPEN B+ TO RELAY

VERIFY ACTIVE DTC

MISSING RELAY

FRONT CONTROL MODULE

REAR WINDOW DEFOGGER RELAY

INTELLIGENT POWER MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRBIII

t, erase the current Front Control Module DTC’s.

Turn the ignition off, wait 10 seconds then turn the ignition on.
With the DRBIII

t, read the current Front Control Module DTC’s.

Does the DRBIII

t display EBL RUN ONLY RELAY OPEN trouble code?

All

Yes

→ Go To 2

No

→ The condition that caused this symptom is currently not present

at this time.
Perform BODY VERIFICATION TEST - VER 1.

2

Turn the ignition off.
Check the IPM to make certain the Rear Window Defogger Relay is present.
Is the Rear Window Defogger Relay present?

All

Yes

→ Go To 3

No

→ Replace the missing Rear Defogger Relay.

Perform BODY VERIFICATION TEST - VER 1.

3

Remove the Rear Window Defogger relay from the IPM.
Measure the voltage of pin 86 in the Rear Defogger Relay socket.
Is the voltage above 10.0 volts?

All

Yes

→ Go To 4

No

→ Repair/replace open B+ to relay as necessary.

Perform BODY VERIFICATION TEST - VER 1.

436

ELECTRICALLY HEATED SYSTEMS

TEST

ACTION

APPLICABILITY

4

Turn the ignition off.
Install a known good relay in place of the Rear Window Defogger relay.
Turn the ignition on.
Attempt to operate the Rear Window Defogger.
With the DRBIII

t, read the current Front Control Module DTC’s.

Does the DTC reset?

All

Yes

→ Go To 5

No

→ Replace the Rear Defogger Relay.

Perform BODY VERIFICATION TEST - VER 1.

5

Turn the ignition off.
Disconnect the Front Control Module from the Fuse and Relay Center.
Remove the Rear Window Defogger Relay.
Measure the resistance of the Rear Window Defogger Relay Control Circuit in the
Fuse and Relay Center.
Is the resistance below 5.0 ohms?

All

Yes

→ Replace the Front Control Module.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Replace the Fuse and Relay Center.

Perform BODY VERIFICATION TEST - VER 1.

437

ELECTRICALLY HEATED SYSTEMS

EBL RUN ONLY RELAY OPEN —

Continued

Symptom:

EBL RUN ONLY RELAY SHORTED TO BATTERY

When Monitored and Set Condition:

EBL RUN ONLY RELAY SHORTED TO BATTERY

When Monitored:

Continuously with the ignition on.

Set Condition:

The FCM has detected a short to battery voltage in the Rear Defogger

Relay control circuit.

POSSIBLE CAUSES

VERIFY ACTIVE DTC

FRONT CONTROL MODULE

INTELLIGENT POWER MODULE

REAR WINDOW DEFOGGER RELAY

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRBIII

t, erase the current Front Control Module DTC’s.

Turn the ignition off, wait 10 seconds then turn the ignition on.
With the DRBIII

t, read the current Front Control Module DTC’s.

Does the DRBIII

t display EBL RUN ONLY RELAY SHORTED TO BATTERY

trouble code?

All

Yes

→ Go To 2

No

→ The condition that caused this symptom is currently not present

at this time.
Perform BODY VERIFICATION TEST - VER 1.

2

Turn the ignition off.
Install a known good relay in place of the Rear Window Defogger relay.
Turn the ignition on.
Attempt to operate the Rear Window Defogger.
With the DRBIII

t, read the current Front Control Module DTCs.

Did the DTC reset?

All

Yes

→ Go To 3

No

→ Replace the Rear Defogger Relay.

Perform BODY VERIFICATION TEST - VER 1.

3

Turn the ignition off.
Remove the Rear Window Defogger Relay from the IPM.
Remove the Front Control Module from the IPM.
Measure the voltage of the Rear Window Relay Control circuit.
Is the voltage above 1.0 volts?

All

Yes

→ Replace the Fuse and Relay Center.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Replace the Front Control Module.

Perform BODY VERIFICATION TEST - VER 1.

438

ELECTRICALLY HEATED SYSTEMS

Symptom:

BACKUP LAMP OUTPUT OPEN

When Monitored and Set Condition:

BACKUP LAMP OUTPUT OPEN

When Monitored:

Trans in reverse.

Set Condition:

Voltage output status is Low.

POSSIBLE CAUSES

INTERMITTENT CONDITION

GROUND CIRCUIT

BACKUP LAMP OPEN

BACKUP LAMP DRIVER CIRCUIT OPEN

BODY CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRBIII

t, clear all BCM, IPM DTC’s.

Actuate the Backup Lamps.
With the DRBIII

t, read the DTC information.

Does the DRBIII

t read: Backup Lamp Output Open?

All

Yes

→ Go To 2

No

→ The condition that caused the symptom is currently not present.

Inspect the related wiring for a possible intermittent condition.
Look for terminal push out or any chafed, pierced, pinched, or
partially broken wires.
Perform BODY VERIFICATION TEST - VER 1.

2

Turn the ignition off
Disconnect the inoperative rear tail lamp harness connector.
Using a 12-volt test light connected to 12-volts, check the ground circuit.
Does the test light illuminate brightly?

All

Yes

→ Go To 3

No

→ Repair the Ground Circuit.

Perform BODY VERIFICATION TEST - VER 1.

439

EXTERIOR LIGHTING

 

 

 

 

 

 

 

Content   ..  798  799  800  801   ..