Chrysler Town, Dodge Caravan. Manual - part 775

 

  Index      Chrysler     Chrysler TOWN & COUNTRY, VOYAGER, Dodge Caravan - service repair manual 2001-2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  773  774  775  776   ..

 

 

Chrysler Town, Dodge Caravan. Manual - part 775

 

 

Symptom:

FCM, PCI INTERNAL FAULT

When Monitored and Set Condition:

FCM, PCI INTERNAL FAULT

When Monitored:

Continuously.

Set Condition:

The DTC will set if the FCM detects an internal fault.

POSSIBLE CAUSES

FCM, PCI INTERNAL FAULT

TEST

ACTION

APPLICABILITY

1

Connect the DRB to the Data Link Connector.
Turn the ignition on.
With the DRB, erase FCM DTC’s.
Turn the ignition off then turn the ignition on.
With the DRB, read FCM DTC’s.
Did this DTC reset?

All

Yes

→ Replace the Front Control Module in accordance with the service

information.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Test Complete.

336

COMMUNICATION

Symptom:

FCM, PCM COMMUNICATION FAULT

When Monitored and Set Condition:

FCM, PCM COMMUNICATION FAULT

When Monitored:

With the ignition in run, and the IOD fuse installed.

Set Condition:

The FCM does not receive any messages from the PCM for at least 5

seconds.

POSSIBLE CAUSES

PCM COMMUNICATION FAULT

ATTEMPT TO COMMUNICATE WITH THE PCM

PCI BUS CIRCUIT OPEN

POWERTRAIN CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, enter Instrument Cluster, System Tests then PCM Monitor.
Does the DRB display: PCM is active on BUS?

All

Yes

→ Erase the DTC, if DTC resets, replace the Front Control Module

in accordance with the service information.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 2

2

Turn the ignition on.
With the DRB, attempt to communicate with the PCM.
Was the DRB able to communicate with the PCM?

All

Yes

→ Go To 3

No

→ Refer to the communication category and perform the appropriate

symptom.
Perform BODY VERIFICATION TEST - VER 1.

337

COMMUNICATION

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Disconnect the PCM harness connector. Note: If equipped with NGC follow the
caution below.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the PCI Bus circuit between the DLC and the PCM
connector.
Is the resistance below 5.0 ohms?

All

Yes

→ Replace and program the Powertrain Control Module in accor-

dance with the Service Information.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Repair the PCI Bus circuit for an open.

Perform BODY VERIFICATION TEST - VER 1.

338

COMMUNICATION

FCM, PCM COMMUNICATION FAULT —

Continued

Symptom:

FCM, RADIO COMMUNICATION FAULT

When Monitored and Set Condition:

FCM, RADIO COMMUNICATION FAULT

When Monitored:

With the ignition in run, and the IOD fuse installed.

Set Condition:

The FCM does not receive any messages from the radio for at least 5

seconds.

POSSIBLE CAUSES

ATTEMPT TO COMMUNICATE WITH THE RADIO

FRONT CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, attempt to communicate with the Radio.
Was the DRB able to I/D or communicate with the Radio?

All

Yes

→ Go To 2

No

→ Refer to the Communication category for the related symptom(s).

Perform BODY VERIFICATION TEST - VER 1.

2

With the DRB, erase DTC’s.
Cycle the ignition switch from off to on and wait approximately 1 minute.
With the DRB, read DTC’s.
Did this DTC reset?

All

Yes

→ Replace the Front Control Module in accordance with the service

information.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Test Complete.

339

COMMUNICATION

 

 

 

 

 

 

 

Content   ..  773  774  775  776   ..