Chrysler Town, Dodge Caravan. Manual - part 760

 

  Index      Chrysler     Chrysler TOWN & COUNTRY, VOYAGER, Dodge Caravan - service repair manual 2001-2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  758  759  760  761   ..

 

 

Chrysler Town, Dodge Caravan. Manual - part 760

 

 

TEST

ACTION

APPLICABILITY

7

Turn the ignition off.
Disconnect the Rear Blower Motor Power Module C1 harness connector.
Measure the resistance between ground and the Ground circuit.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 8

No

→ Repair the Ground circuit for an open.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

8

Turn the ignition off.
Disconnect the Rear Blower Motor Power Module C1 harness connector.
Disconnect the Automatic Temperature Control Module C2 harness connector.
Turn the ignition on.
Measure the voltage of the Rear Blower Motor Control circuit.
Is there any voltage present?

All

Yes

→ Repair the Rear Blower Motor Control circuit for a short to

voltage.
With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 9

9

Turn the ignition off.
Disconnect the Rear Blower Motor Power Module C1 harness connector.
Disconnect the Automatic Temperature Control Module C2 harness connector.
Measure the resistance of the Rear Blower Motor Control circuit between the Rear
Blower Motor Power Module C1 harness connector and the Automatic Temperature
Control Module C2 harness connector.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 10

No

→ Repair the Rear Blower Motor Control circuit for an open.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

10

Turn the ignition off.
Make sure that the Rear Blower Motor Power Module C1 harness connector is
connected to the Rear Blower Motor Power Module.
Make sure that the Automatic Temperature Control Module C2 harness connector is
connected to the Automatic Temperature Control Module.
Start the engine.
Press the ATC Power switch on.
Set the Rear System switch on the ATC module to the Rear Control position.
Set the blower switch on the Rear ATC Control panel to LO speed.
While back probing, measure the voltage of the Rear Blower Motor Control circuit in
the Automatic Temperature Control Module C2 harness connector.
Is the voltage above 10.0 volts?

All

Yes

→ Go To 11

No

→ Replace the Rear Blower Motor Power Module in accordance with

the Service Information.
With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

276

AUTOMATIC TEMPERATURE CONTROL

*REAR BLOWER MOTOR INOPERATIVE —

Continued

TEST

ACTION

APPLICABILITY

11

Turn the ignition off.
Reconnect all previously disconnected components.
Connect the DRBIII

t X10 Scope Probe CH7061 to Channel 1 on the DRBIIIt.

Select the following from the DRBIII

t menu: PEP Module Tools; Lab Scope; Live

Data; and Lab Scope.
Press F2 and then press Enter.
Using the left/right arrow keys, set the time to 10ms/Div.
Press F2.
Using the up/down arrow keys, set the voltage range to +20.0v.
Press Enter to move the cursor to Probe.
Using the up/down arrow keys, set the Probe to X10.
Press F2.
Start the engine.
Press the ATC Power switch on.
Set the Rear System switch on the ATC module to the Rear Control position.
Using the X10 Scope Probe, back probe the Rear Blower Motor Control circuit in the
Automatic Temperature Control Module C2 harness connector.
NOTE: The Rear Blower Motor Power Module provides a 10.0 volt signal to
the ATC Module over the Rear Blower Motor Control circuit. The ATC
Module provides a variable duty cycle ground to the 10.0 volt signal based
on input from the Rear Blower switch.
NOTE: When the Rear Blower switch is set to LO speed, the ATC Module
provides a short duty cycle (less time grounding the signal voltage).
NOTE: As higher blower speeds are requested, the ATC Module increases
the duty cycle (more time grounding the signal voltage).
NOTE: When the Rear Blower switch reaches HI speed, the duty cycle
increases to where the signal pattern is almost a flat line (with brief voltage
spikes).
Set the blower switch on the Rear ATC Control panel to LO speed then slowly move
it to HI speed while observing the DRBIII

t display.

The voltage on the scope patten should cycle from approximately 2.0 volts (duty cycle
on) to 10.0 volts (duty cycle off) for all blower speeds.
The duty cycle pattern should change smoothly as the Rear Blower switch is turned
from LO to HI.
The duty cycle on time should change from approximately 8 ms at LO speed, to 15 ms
at medium speed, and to 25 ms at HI speed.
Does the DRBIII

t display the voltage range and duty cycle as described above?

All

Yes

→ Go To 12

No

→ Replace the Automatic Temperature Control Module in accor-

dance with the Service Information.
With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

277

AUTOMATIC TEMPERATURE CONTROL

*REAR BLOWER MOTOR INOPERATIVE —

Continued

TEST

ACTION

APPLICABILITY

12

Turn the ignition off.
Disconnect the Rear Blower Motor Power Module C1 harness connector.
Disconnect the Rear Blower Motor Power Module C2 harness connector.
Connect a jumper wire between the Fused Rear Blower Relay Output circuit in the
Rear Blower Motor Power Module C1 harness connector and the Power Feed circuit
in the Rear Blower Motor Power Module C2 harness connector.
Connect a jumper wire between the Ground circuit in the Rear Blower Motor Power
Module C1 harness connector and the Ground circuit in the Rear Blower Motor
Power Module C2 harness connector.
Turn the ignition on.
Does the Blower Motor operate at full speed?

All

Yes

→ Replace the Rear Blower Motor Power Module in accordance with

the Service Information.
With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Replace the Blower Motor in accordance with the Service Infor-

mation.
With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

13

Turn the ignition off.
Remove the Rear Blower Motor Relay from the IPM.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Using a 12-volt test light connected to ground, probe cavity 30 of the Rear Blower
Motor Relay connector.
Does the test light illuminate brightly?

All

Yes

→ Go To 14

No

→ Replace the IPM in accordance with the Service Information.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

14

Turn the ignition off.
Remove the Rear Blower Motor Relay from the IPM.
Remove IPM Fuse #12.
Measure the resistance between cavity 87 of the Rear Blower Motor Relay connector
and IPM Fuse #12 (power input cavity).
Is the resistance below 5 ohms?

All

Yes

→ Go To 15

No

→ Replace the IPM in accordance with the Service Information.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

278

AUTOMATIC TEMPERATURE CONTROL

*REAR BLOWER MOTOR INOPERATIVE —

Continued

TEST

ACTION

APPLICABILITY

15

Turn the ignition off.
Make sure that the Rear Blower Motor Relay is installed.
Remove IPM Fuse #12.
Turn the ignition on.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Using a 12-volt test light connected to ground, probe IPM Fuse #12 (power input
cavity).
Does the test light illuminate brightly?

All

Yes

→ Go To 16

No

→ Replace the Rear Blower Motor Relay in accordance with the

Service Information.
With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

16

Turn the ignition off.
Remove IPM Fuse #12.
Disconnect the IPM C8 harness connector.
Measure the resistance between IPM Fuse #12 (power output cavity) and cavity 7 of
the IPM C8 connector (IPM side).
Is the resistance below 5 ohms?

All

Yes

→ Repair the Fused Rear Blower Motor Relay Output circuit for an

open.
With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Replace the IPM in accordance with the Service Information.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

279

AUTOMATIC TEMPERATURE CONTROL

*REAR BLOWER MOTOR INOPERATIVE —

Continued

 

 

 

 

 

 

 

Content   ..  758  759  760  761   ..