Chrysler Town, Dodge Caravan. Manual - part 748

 

  Index      Chrysler     Chrysler TOWN & COUNTRY, VOYAGER, Dodge Caravan - service repair manual 2001-2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  746  747  748  749   ..

 

 

Chrysler Town, Dodge Caravan. Manual - part 748

 

 

Symptom:

FRONT MODE DOOR NOT RESPONDING (ACTIVE)

When Monitored and Set Condition:

FRONT MODE DOOR NOT RESPONDING (ACTIVE)

When Monitored:

With the ignition on and the IOD fuse installed.

Set Condition:

This DTC is set if the ATC does not receive feedback pulses within 5

seconds of the drive voltage being applied.

POSSIBLE CAUSES

MODE DOOR DRIVER CIRCUIT (A) SHORTED TO GROUND

MODE DOOR DRIVER CIRCUIT (B) SHORTED TO GROUND

MODE DOOR DRIVER CIRCUITS (A) AND (B) SHORTED TOGETHER

MODE DOOR DRIVER CIRCUIT (A) OPEN

MODE DOOR DRIVER CIRCUIT (B) OPEN

ATC

MODE DOOR ACTUATOR

TEST

ACTION

APPLICABILITY

1

Turn the ignition off.
Disconnect the Mode Door Actuator harness connector.
Disconnect the ATC C1 harness connector.
Measure the resistance between ground and the Mode Door Driver (A) circuit.
Is the resistance above 100k ohms?

All

Yes

→ Go To 2

No

→ Repair the Mode Door Driver (A) circuit for a short to ground.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

2

Turn the ignition off.
Disconnect the Mode Door Actuator harness connector.
Disconnect the ATC C1 harness connector.
Measure the resistance between ground and the Mode Door Driver (B) circuit.
Is the resistance above 100k ohms?

All

Yes

→ Go To 3

No

→ Repair the Mode Door Driver (B) circuit for a short to ground.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

228

AUTOMATIC TEMPERATURE CONTROL

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Disconnect the Mode Door Actuator harness connector.
Disconnect the ATC C1 harness connector.
Measure the resistance between the Mode Door Driver (B) circuit and the Mode Door
Driver (A) circuit.
Is the resistance above 100k ohms?

All

Yes

→ Go To 4

No

→ Repair the Mode Door Driver (A) and (B) circuits for a short

together.
With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

4

Turn the ignition off.
Disconnect the Mode Door Actuator harness connector.
Disconnect the ATC C1 harness connector.
Measure the resistance of the Mode Door Driver (A) circuit.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 5

No

→ Repair the Mode Door Driver (A) circuit for an open.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

5

Turn the ignition off.
Disconnect the Mode Door Actuator harness connector.
Disconnect the ATC C1 harness connector.
Measure the resistance of the Mode Door Driver (B) circuit.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 6

No

→ Repair the Mode Door Driver (B) circuit for an open.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

6

Turn the ignition off.
Disconnect the ATC C1 harness connector.
Measure the resistance between the Mode Door Driver (A) circuit and the Mode Door
Driver (B) circuit.
Is the resistance between 26.0 and 46.0 ohms?

All

Yes

→ Replace the ATC.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 7

7

If there are no possible causes remaining, view repair.

All

Repair

Replace the Mode Door Actuator.
With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

229

AUTOMATIC TEMPERATURE CONTROL

FRONT MODE DOOR NOT RESPONDING (ACTIVE) —

Continued

Symptom:

FRONT MODE DOOR TRAVEL TOO LARGE (ACTIVE)

When Monitored and Set Condition:

FRONT MODE DOOR TRAVEL TOO LARGE (ACTIVE)

When Monitored:

With the ignition on and the IOD fuse installed.

Set Condition:

This DTC is set when the ATC monitors the travel range during system

initialization and the measured range is greater than expected.

POSSIBLE CAUSES

CHECK THE ATC FOR DTCS

MODE DOOR ACTUATOR

MODE DOOR LINKAGE

ATC

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, read the active ATC DTCs.
Is the FRONT MODE DOOR NOT RESPONDING DTC set?

All

Yes

→ Return to the symptom list and choose the symptom.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 2

2

Turn the ignition off.
Remove the Mode Door Actuator.
By hand, attempt to rotate the Mode Door Actuator in both directions.
Did the Mode Door Actuator turn in either direction?

All

Yes

→ Replace the Mode Door Actuator.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 3

3

Remove the Mode Door Actuator. Rotate the mode doors (doors only). Note: These
should rotate approximately 45 degrees from stop to stop.
Inspect the mode door linkage for excessive wear or missing linkage.
Were any mechanical problems found?

All

Yes

→ Repair or replace the mode door/linkage as necessary.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Replace the ATC.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

230

AUTOMATIC TEMPERATURE CONTROL

Symptom:

FRONT MODE DOOR TRAVEL TOO SMALL (ACTIVE)

When Monitored and Set Condition:

FRONT MODE DOOR TRAVEL TOO SMALL (ACTIVE)

When Monitored:

With the ignition on and the IOD fuse installed.

Set Condition:

This DTC is set when the ATC monitors the travel range during system

initialization and the measured range is less than expected.

POSSIBLE CAUSES

CHECK THE ATC FOR DTCS

ATC

OBSTRUCTED MODE DOOR

MODE DOOR ACTUATOR

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, read the active ATC DTCs.
Is the FRONT MODE DOOR NOT RESPONDING DTC set?

All

Yes

→ Return to the symptom list and choose the symptom.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 2

2

Turn the ignition off.
Disconnect the Mode Door Actuator harness connector.
Connect a 12-volt Test Light between the Mode Door Actuator harness connector
cavities.
Turn the ignition on.
While monitoring the test light, turn the mode control knob to each position.
Note: Observe test light for approximately 30 seconds.
Does the test light start to flash and stay flashing?

All

Yes

→ Go To 3

No

→ Replace the ATC.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

3

Remove the Mode Door Actuator. Rotate the mode doors (doors only). Note: These
should rotate approximately 45 degrees from stop to stop.
Do the mode doors move smoothly in both directions?

All

Yes

→ Replace the Mode Door Actuator.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Repair or replace the mode door as necessary.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

231

AUTOMATIC TEMPERATURE CONTROL

 

 

 

 

 

 

 

Content   ..  746  747  748  749   ..