Chrysler Town, Dodge Caravan. Manual - part 743

 

  Index      Chrysler     Chrysler TOWN & COUNTRY, VOYAGER, Dodge Caravan - service repair manual 2001-2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  741  742  743  744   ..

 

 

Chrysler Town, Dodge Caravan. Manual - part 743

 

 

Symptom:

DRIVER BLEND DOOR NOT RESPONDING (ACTIVE)

When Monitored and Set Condition:

DRIVER BLEND DOOR NOT RESPONDING (ACTIVE)

When Monitored:

With the ignition on and the IOD fuse installed.

Set Condition:

This DTC is set if the ATC does not receive feedback pulses within 5

seconds of the drive voltage being applied.

POSSIBLE CAUSES

DRIVER BLEND DOOR DRIVER CIRCUIT (A) SHORTED TO GROUND

DRIVER BLEND DOOR DRIVER CIRCUIT (B) SHORTED TO GROUND

DRIVER BLEND DOOR DRIVER CIRCUITS (A) AND (B) SHORTED TOGETHER

DRIVER BLEND DOOR DRIVER CIRCUIT (A) OPEN

DRIVER BLEND DOOR DRIVER CIRCUIT (B) OPEN

ATC

DRIVER BLEND DOOR ACTUATOR

TEST

ACTION

APPLICABILITY

1

Turn the ignition off.
Disconnect the Driver Blend Door Actuator harness connector.
Disconnect the ATC C1 harness connector.
Measure the resistance between ground and the Driver Blend Door Driver (A) circuit.
Is the resistance above 100k ohms?

All

Yes

→ Go To 2

No

→ Repair the Driver Blend Door Driver (A) circuit for a short to

ground.
With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

2

Turn the ignition off.
Disconnect the Driver Blend Door Actuator harness connector.
Disconnect the ATC C1 harness connector.
Measure the resistance between ground and the Driver Blend Door Driver (B) circuit.
Is the resistance above 100k ohms?

All

Yes

→ Go To 3

No

→ Repair the Driver Blend Door Driver (B) circuit for a short to

ground.
With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

208

AUTOMATIC TEMPERATURE CONTROL

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Disconnect the Driver Blend Door Actuator harness connector.
Disconnect the ATC C1 harness connector.
Measure the resistance between the Driver Blend Door Driver (A) and (B) circuits.
Is the resistance above 100k ohms?

All

Yes

→ Go To 4

No

→ Repair the Driver Blend Door Driver (A) and (B) circuits for a

short together.
With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

4

Turn the ignition off.
Disconnect the Driver Blend Door Actuator harness connector.
Disconnect the ATC C1 harness connector.
Measure the resistance of the Driver Blend Door Driver (A) circuit.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 5

No

→ Repair the Driver Blend Door Driver (A) circuit for an open.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

5

Turn the ignition off.
Disconnect the Driver Blend Door Actuator harness connector.
Disconnect the ATC C1 harness connector.
Measure the resistance of the Driver Blend Door Driver (B) circuit.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 6

No

→ Repair the Driver Blend Door Driver (B) circuit for an open.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

6

Turn the ignition off.
Disconnect the ATC C1 harness connector.
Measure the resistance between the Driver Blend Door Driver (A) and (B) circuits.
Is the resistance between 26.0 and 46.0 ohms?

All

Yes

→ Replace the ATC.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 7

7

If there are no possible causes remaining, view repair.

All

Repair

Replace the Driver Blend Door Actuator.
With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

209

AUTOMATIC TEMPERATURE CONTROL

DRIVER BLEND DOOR NOT RESPONDING (ACTIVE) —

Continued

Symptom:

DRIVER BLEND DOOR TRAVEL TOO LARGE (ACTIVE)

When Monitored and Set Condition:

DRIVER BLEND DOOR TRAVEL TOO LARGE (ACTIVE)

When Monitored:

With the ignition on and the IOD fuse installed.

Set Condition:

This DTC is set when the ATC monitors the travel range during system

initialization and the measured range is greater than expected.

POSSIBLE CAUSES

CHECK THE ATC FOR DTCS

DRIVER BLEND DOOR ACTUATOR

DRIVER BLEND DOOR LINKAGE

ATC

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, read the active ATC DTCs.
Is the DRIVER BLEND DOOR NOT RESPONDING DTC set?

All

Yes

→ Return to the symptom list and choose the symptom.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 2

2

Turn the ignition off.
Remove the Driver Blend Door Actuator.
By hand, attempt to rotate the driver blend door motor in both directions.
Did the blend door actuator turn in either direction?

All

Yes

→ Replace the Driver Blend Door Actuator.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 3

3

Remove the Driver Blend Door Actuator. Rotate the blend door (door only). Note: This
should rotate approximately 45 degrees from stop to stop.
Inspect the blend door linkage for excessive wear or missing linkage.
Were any mechanical problems found?

All

Yes

→ Repair or replace the driver blend door/linkage as necessary.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Replace the ATC.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

210

AUTOMATIC TEMPERATURE CONTROL

Symptom:

DRIVER BLEND DOOR TRAVEL TOO SMALL (ACTIVE)

When Monitored and Set Condition:

DRIVER BLEND DOOR TRAVEL TOO SMALL (ACTIVE)

When Monitored:

With the ignition on and the IOD fuse installed.

Set Condition:

This DTC is set when the ATC monitors the travel range during system

initialization and the measured range is less than expected.

POSSIBLE CAUSES

CHECK THE ATC FOR DTCS

ATC

OBSTRUCTED BLEND DOOR

DRIVER BLEND DOOR ACTUATOR

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, read the active ATC DTCs.
Is the DRIVER BLEND DOOR NOT RESPONDING DTC set?

All

Yes

→ Return to the symptom list and choose the symptom.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 2

2

Turn the ignition off.
Disconnect the Driver Blend Door Actuator harness connector.
Connect a 12-volt Test Light between the Driver Blend Door Actuator harness
connector cavities.
Turn the ignition on.
While monitoring the test light, press the driver blend control to change the setting
from lo to hi.
Note: Observe test light for approximately 30 seconds.
Does the test light start to flash and stay flashing?

All

Yes

→ Go To 3

No

→ Replace the ATC.

With the DRBIII

t, reset the ATC after repair is complete.

Perform BODY VERIFICATION TEST - VER 1.

211

AUTOMATIC TEMPERATURE CONTROL

 

 

 

 

 

 

 

Content   ..  741  742  743  744   ..