Chrysler Town, Dodge Caravan. Manual - part 644

 

  Index      Chrysler     Chrysler TOWN & COUNTRY, VOYAGER, Dodge Caravan - service repair manual 2001-2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  642  643  644  645   ..

 

 

Chrysler Town, Dodge Caravan. Manual - part 644

 

 

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Disconnect the Vehicle Speed Sensor harness connector.
Turn the ignition on.
Measure the voltage of the (G7) VSS Signal circuit in the VSS harness connector.
Is the voltage between 4.5 to 5.0 volts?

All

Yes

→ Go To 4

No

→ Go To 5

4

Turn the ignition off.
Disconnect the Vehicle Speed Sensor harness connector.
Measure the resistance of the (K4) Sensor ground circuit between the VSS harness
connector and ground.
Is the resistance below 5.0 ohms?

All

Yes

→ Remove and inspect the Pinion Gear. If OK, replace the Vehicle

Speed Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→ Repair the (K4) Sensor ground circuit for an open.

Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

5

Turn the ignition off.
Disconnect the Vehicle Speed Sensor harness connector.
Disconnect the PCM harness connector.
Measure the resistance of the (G7) Vehicle Speed Sensor Signal circuit in the VSS
harness connector to ground.
Is the resistance below 100 ohms?

All

Yes

→ Repair the (G7) VSS Signal circuit for a short to ground.

Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→ Go To 6

6

Turn the ignition off.
Disconnect the Vehicle Speed Sensor harness connector.
Disconnect the PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (G7) VSS Signal circuit between the VSS harness
connector and to the appropriate terminal of special tool #8815.
Is the resistance below 5 ohms?

All

Yes

→ Go To 7

No

→ Repair the (G7) VSS Signal circuit for an open.

Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

7

NOTE: Before continuing, check the PCM harness connector terminals for
corrosion, damage, or terminal push out. Repair as necessary.
If there are no possible causes remaining, view repair,

All

Repair

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

384

DRIVEABILITY - NGC

P0501-VEHICLE SPEED SENSOR #1 PERFORMANCE (MANUAL TRANS)

Continued

Symptom List:

P0506-IDLE SPEED LOW PERFORMANCE
P0507-IDLE SPEED HIGH PERFORMANCE
P0519-IDLE SPEED PERFORMANCE

Test Note:

All symptoms listed above are diagnosed using the same tests.

The title for the tests will be P0506-IDLE SPEED LOW PER-
FORMANCE.

When Monitored and Set Condition:

P0506-IDLE SPEED LOW PERFORMANCE

When Monitored:

Engine Running. During an idle condition.

Set Condition:

If the engine RPM does not come within a calibratable low limit of the

target idle speed, a failure timer will increment. When the appropriate failure timer
reaches its maximum threshold without sign of RPM trending towards control, a soft fail
is generated. When a calibratable number of the soft fails is reached, a I trip fault is set.
When two 1 trip faults occur in a row, a the DTC is set and the MIL illuminates.

P0507-IDLE SPEED HIGH PERFORMANCE

When Monitored:

Engine Running. During an idle condition.

Set Condition:

If the engine RPM does not come within a calibratable high limit of the

target idle speed, a failure timer will increment. When the appropriate failure timer
reaches its maximum threshold without sign of RPM trending towards control, a soft fail
is generated. When a calibratable number of the soft fails is reached, a I trip fault is set.
When two 1 trip faults occur in a row, a the DTC is set and the MIL illuminates.

P0519-IDLE SPEED PERFORMANCE

When Monitored:

With the engine idling and the transmission in drive, if automatic.

There must not be a MAP sensor trouble code or a Throttle Position Sensor trouble code.

Set Condition:

The engine idle is not within 200 rpm above or 100 rpm below the target

idle for 40 seconds. Two trip fault.

POSSIBLE CAUSES

GOOD TRIP EQUAL TO ZERO

IAC MOTOR PASSAGES

VACUUM LEAKS

AIR INDUCTION SYSTEM

THROTTLE BODY AND THROTTLE LINKAGE

385

DRIVEABILITY - NGC

TEST

ACTION

APPLICABILITY

1

Ignition on, engine not running.
With the DRBIII

t, read DTCs and record the related Freeze Frame data.

Is the Good Trip Counter displayed and equal to zero?

All

Yes

→ Go To 2

No

→ Refer to the INTERMITTENT CONDITION symptom in the

Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

2

Turn the ignition off.
Remove the IAC Motor.
Inspect the IAC Motor and passages for any obstructions or damage to motor.
Were any problems found?

All

Yes

→ Repair as necessary.

Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→ Go To 3

3

Start the engine.
Inspect the vehicle for external vacuum leaks.
Inspect the engine for internal vacuum leaks.
Were any vacuum leaks found?

All

Yes

→ Repair the vacuum leak as necessary.

Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→ Go To 4

4

Inspect the Air Induction System for the following problems.
Restrictions: Dirty Air Cleaner, Foreign material trapped in the air intake tube, etc.
Leaks: Air Intake tube connection, Air Cleaner housing, etc.
Were any problems found?

All

Yes

→ Repair or replace as necessary.

Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→ Go To 5

5

Inspect the throttle body plate carbon build up or other restrictions.
Inspect the throttle linkage for binding and smooth operation.
Ensure the throttle plate is resting on the stop at idle.
Were any problems found?

All

Yes

→ Repair or replace as necessary.

Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→ Test Complete.

386

DRIVEABILITY - NGC

P0506-IDLE SPEED LOW PERFORMANCE —

Continued

Symptom:

P0508-IAC VALVE SENSE CIRCUIT LOW

When Monitored and Set Condition:

P0508-IAC VALVE SENSE CIRCUIT LOW

When Monitored:

Engine running. Battery voltage greater than 10 volts.

Set Condition:

The IAC sense circuit is less than 175 mA. One Trip Fault.

POSSIBLE CAUSES

IAC MOTOR OPERATION

IAC MOTOR

(K39) IAC MOTOR CONTROL CIRCUIT SHORTED TO GROUND

(K60) IAC SIGNAL CIRCUIT OPEN

(K60) IAC SIGNAL CIRCUIT SHORTED TO GROUND

(K39) IAC MOTOR CONTROL CIRCUIT OPEN

PCM

TEST

ACTION

APPLICABILITY

1

NOTE: If the engine will not idle, maintain an engine speed between 800 and
1500 RPM.
Start the engine.
Allow the engine to idle.
With the DRBIII

t, read the IAC Current.

Is the IAC Current below 146 mA?

All

Yes

→ Go To 2

No

→ Refer to the INTERMITTENT CONDITION symptom in the

Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

2

Turn the ignition off.
Disconnect the IAC Motor harness connector.
Remove the IAC Motor.
NOTE: Inspect the IAC air passages for restriction and damage to the IAC
valve.
Measure the resistance across the IAC Motor pin terminals (component).
Is the resistance 9.7 +/- 1.0 ohms?

All

Yes

→ Go To 3

No

→ Replace the IAC Motor.

Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

387

DRIVEABILITY - NGC

 

 

 

 

 

 

 

Content   ..  642  643  644  645   ..