Chrysler Town, Dodge Caravan. Manual - part 623

 

  Index      Chrysler     Chrysler TOWN & COUNTRY, VOYAGER, Dodge Caravan - service repair manual 2001-2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  621  622  623  624   ..

 

 

Chrysler Town, Dodge Caravan. Manual - part 623

 

 

Symptom List:

P0135-O2 SENSOR 1/1 HEATER PERFORMANCE
P0141-O2 SENSOR 1/2 HEATER PERFROMANCE

Test Note:

All symptoms listed above are diagnosed using the same tests.

The title for the tests will be P0135-O2 SENSOR 1/1 HEATER
PERFORMANCE.

When Monitored and Set Condition:

P0135-O2 SENSOR 1/1 HEATER PERFORMANCE

When Monitored:

Engine Running and Heater duty cycle greater than 0%

Set Condition:

O2 Heater Temperature does not reach 575°C (959°F) within 45 second

during monitoring conditions. Two Trip Fault.

P0141-O2 SENSOR 1/2 HEATER PERFROMANCE

When Monitored:

Engine Running and Heater duty cycle greater than 0%.

Set Condition:

O2 Heater Temperature does not reach 400°C (752°F) within 45 second

during monitoring conditions. Two Trip Fault.

POSSIBLE CAUSES

O2 SENSOR HEATER OPERATION

O2 HEATER ELEMENT

O2 HEATER GROUND CIRCUIT OPEN

O2 HEATER CONTROL CIRCUIT OPEN

PCM

TEST

ACTION

APPLICABILITY

1

Ignition on, engine not running.
With the DRBIII

t, read DTCs and record the related Freeze Frame data.

Is the Good Trip Counter display and equal to zero?

All

Yes

→ Go To 3

No

→ Go To 2

300

DRIVEABILITY - NGC

TEST

ACTION

APPLICABILITY

2

Turn the ignition off.
NOTE: Allow the O2 Sensor to cool down before continuing the test. The O2
voltage should stabilize at 5.0 volts. Raising the hood may help in reducing
under hood temps.
Ignition on, engine not running.
With the DRBIII

t, actuate the O2 Heater Test.

With the DRBIII

t, monitor O2 Sensor voltage for at least 2 minutes.

Does the voltage stay above 4.5 volts?

All

Yes

→ Go To 3

No

→ Refer to the INTERMITTENT CONDITION symptom in the

Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

3

NOTE: Allow the O2 sensor to cool down to room temperature.
Turn the ignition off.
Disconnect the O2 Sensor harness connector.
Measure the resistance across the O2 Sensor Heater element component side.
NOTE: O2 Sensor Heater Resistance Specification: 1/1 and 2/1 = 3.0 to 4.0
ohms or 1/2 and 2/2 = 4.0 to 5.0 ohms.
Is the resistance within the specifications?

All

Yes

→ Go To 4

No

→ Replace the O2 Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

4

Turn the ignition off.
Disconnect the O2 Sensor harness connector.
Measure the resistance between an engine ground and the O2 Heater Ground circuit
in the O2 Sensor harness connector.
Is the resistance below 0.5 of an ohm?

All

Yes

→ Go To 5

No

→ Repair the open/high resistance in the O2 Heater Ground circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

5

Turn the ignition off.
Disconnect the O2 Sensor harness connector.
Disconnect the PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the O2 Heater Control circuit from the O2 Sensor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 0.5 of an ohm?

All

Yes

→ Go To 6

No

→ Repair the open/high resistance in the O2 Heater Control circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

301

DRIVEABILITY - NGC

P0135-O2 SENSOR 1/1 HEATER PERFORMANCE —

Continued

TEST

ACTION

APPLICABILITY

6

NOTE: Before continuing, check the PCM harness connector terminals for
corrosion, damage, terminal push out. Repair as necessary.
If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

302

DRIVEABILITY - NGC

P0135-O2 SENSOR 1/1 HEATER PERFORMANCE —

Continued

Symptom:

P0171-FUEL SYSTEM 1/1 LEAN

When Monitored and Set Condition:

P0171-FUEL SYSTEM 1/1 LEAN

When Monitored:

With the engine running in closed loop mode, the ambient/battery

temperature above 20°F(-7C) and altitude below 8500 ft.

Set Condition:

If the PCM multiplies short term compensation by long term adaptive and

a certain percentage is exceeded for two trips, a freeze frame is stored, the MIL illuminates
and a trouble code is stored.

POSSIBLE CAUSES

GOOD TRIP EQUAL TO ZERO

RESTRICTED FUEL SUPPLY LINE

FUEL PUMP INLET STRAINER PLUGGED

FUEL PUMP MODULE

O2 SENSOR

O2 SIGNAL CIRCUIT

O2 RETURN CIRCUIT

O2 SENSOR HEATER OPERATION

THROTTLE POSITION SENSOR SWEEP

MAP SENSOR OPERATION

ECT SENSOR OPERATION

ENGINE MECHANICAL PROBLEM

FUEL CONTAMINATION/EXHAUST LEAK

TEST

ACTION

APPLICABILITY

1

NOTE: Check for contaminates that may have damaged the O2 Sensor:
contaminated fuel, unapproved silicone, oil and coolant.
NOTE: Diagnose any Misfire DTC(s) first, if set along with the fuel system
DTC.
Ignition on, engine not running.
With the DRBIII

t, read DTCs and record the related Freeze Frame data.

Is the Good Trip Counter displayed and equal to zero?

All

Yes

→ Go To 2

No

→ Refer to the INTERMITTENT CONDITION symptom in the

Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

303

DRIVEABILITY - NGC

 

 

 

 

 

 

 

Content   ..  621  622  623  624   ..