Chrysler Town, Dodge Caravan. Manual - part 1141

 

  Index      Chrysler     Chrysler TOWN & COUNTRY, VOYAGER, Dodge Caravan - service repair manual 2001-2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1139  1140  1141  1142   ..

 

 

Chrysler Town, Dodge Caravan. Manual - part 1141

 

 

Symptom:

P0520-OIL PRESS SENSOR CKT MALF SIGNAL VOLTAGE TOO
LOW

When Monitored and Set Condition:

P0520-OIL PRESS SENSOR CKT MALF SIGNAL VOLTAGE TOO LOW

When Monitored:

With the engine running.

Set Condition:

The ECM detects the Oil Pressure Sensor Signal voltage below .5 volt for

more than 3 seconds.

POSSIBLE CAUSES

ECM - OIL PRESSURE SENSOR SIGNAL SHORT TO GROUND

ENGINE OIL PRESSURE SENSOR

OIL PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO GROUND

OIL PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO SENSOR GROUND

INTERMITTENT CONDITION

TEST

ACTION

APPLICABILITY

1

NOTE: If the ECM detects and stores a DTC, the ECM also stores the
engine/vehicle operating conditions under which the DTC was set. Some of
these conditions are displayed on the DRB at the same time the DTC is
displayed.
NOTE: Before erasing stored DTCs, record these conditions. Attempting to
duplicate these conditions may assist when checking for an active DTC.
Turn the ignition on.
With the DRBIII

t, erase ECM DTCs.

Cycle the ignition key on and off several times, leaving the key on for at least 10
seconds at a time.
With the DRBIII

t, read ECM DTCs.

Did this DTC set again?

All

Yes

→ Go To 2

No

→ Go To 5

2

Turn the ignition off.
Disconnect the Oil Pressure Sensor harness connector.
Measure the voltage of the Oil Pressure Sensor Signal circuit.
Is the voltage between 4.7 and 5.3 volts?

All

Yes

→ Replace the Engine Oil Pressure Sensor.

Perform ROAD TEST VERIFICATION - VER-2.

No

→ Go To 3

107

DRIVEABILITY - DIESEL

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Disconnect the ECM harness connectors.
Disconnect the Oil Pressure Sensor harness connector.
Measure the resistance between ground and the Oil Pressure Sensor Signal circuit.
Is the resistance above 100 kohms?

All

Yes

→ Go To 4

No

→ Repair the Oil Pressure Sensor Signal circuit for a short to

ground.
Perform ROAD TEST VERIFICATION - VER-2.

4

Turn the ignition off.
Disconnect the ECM harness connectors.
Disconnect the Oil Pressure Sensor harness connector.
Measure the resistance between Sensor Ground and the Oil Pressure Sensor Signal
circuit.
Is the resistance above 100 kohms?

All

Yes

→ Replace and program the Engine Control Module in accordance

with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

No

→ Repair the Oil Pressure Sensor Signal circuit for a short to Sensor

Ground.
Perform ROAD TEST VERIFICATION - VER-2.

5

WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running and at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the
conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?

All

Yes

→ Repair as necessary.

Perform ROAD TEST VERIFICATION - VER-2.

No

→ Test Complete.

108

DRIVEABILITY - DIESEL

P0520-OIL PRESS SENSOR CKT MALF SIGNAL VOLTAGE TOO LOW —

Continued

Symptom:

P0520-OIL PRESS SENSOR CKT MALF SUPPLY VOLTAGE TOO
HIGH OR LOW

When Monitored and Set Condition:

P0520-OIL PRESS SENSOR CKT MALF SUPPLY VOLTAGE TOO HIGH OR LOW

When Monitored:

With the ignition on.

Set Condition:

The Sensor Reference Voltage A voltage to the Oil Pressure Sensor is

below 4.8 volts or above 5.2 volts for at least 100 ms.

POSSIBLE CAUSES

INTERMITTENT CONDITION

5-VOLT SUPPLY CIRCUIT SHORTED TO GROUND

5-VOLT SUPPLY CIRCUIT SHORTED TO SENSOR GROUND

5-VOLT SUPPLY CIRCUIT SHORTED TO VOLTAGE

ENGINE CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

NOTE: If DTC P0641 or P0651 is present with this DTC, diagnose DTCs
P0641 and P0651 before diagnosing this DTC.
NOTE: If the ECM detects and stores a DTC, the ECM also stores the
engine/vehicle operating conditions under which the DTC was set. Some of
these conditions are displayed on the DRB at the same time the DTC is
displayed.
NOTE: Before erasing stored DTCs, record these conditions. Attempting to
duplicate these conditions may assist when checking for an active DTC.
Turn the ignition on.
With the DRB, erase ECM DTCs.
Turn the ignition off, wait 30 seconds, then start and idle the engine.
With the DRB, read ECM DTCs.
Did this DTC set again?

All

Yes

→ Go To 2

No

→ Go To 5

109

DRIVEABILITY - DIESEL

TEST

ACTION

APPLICABILITY

2

Turn the ignition off.
Disconnect the Oil Pressure Sensor harness connector.
Disconnect the ECM harness connectors.
Remove the ECM/PCM Relay from the IPM.
Connect a jumper wire between cavity 30 and cavity 87 of the ECM/PCM Relay
connector.
Turn the ignition on.
Measure the voltage between ground and the 5-volt Supply circuit at the Oil Pressure
Sensor harness connector.
Is the voltage above 1.0 volt?

All

Yes

→ Repair the 5-volt Supply circuit for a short to voltage.

Perform ROAD TEST VERIFICATION - VER-2.

No

→ Go To 3

3

Turn the ignition off.
Disconnect the ECM harness connectors.
Disconnect the Oil Pressure Sensor harness connector.
Measure the resistance between ground and the 5-volt Supply circuit at the Oil
Pressure Sensor harness connector.
Is the resistance above 1000 ohms?

All

Yes

→ Go To 4

No

→ Repair the 5-volt Supply circuit for a short to ground.

Perform ROAD TEST VERIFICATION - VER-2.

4

Turn the ignition off.
Disconnect the ECM harness connectors.
Disconnect the Oil Pressure Sensor harness connector.
Measure the resistance between Sensor Ground and the 5-volt Supply circuit at the
Oil Pressure Sensor harness connector.
Is the resistance above 1000 ohms?

All

Yes

→ Replace and program the Engine Control Module in accordance

with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

No

→ Repair the 5-volt Supply circuit for a short to Sensor Ground.

Perform ROAD TEST VERIFICATION - VER-2.

110

DRIVEABILITY - DIESEL

P0520-OIL PRESS SENSOR CKT MALF SUPPLY VOLTAGE TOO HIGH OR
LOW —

Continued

 

 

 

 

 

 

 

Content   ..  1139  1140  1141  1142   ..