Chrysler Town, Dodge Caravan. Manual - part 1037

 

  Index      Chrysler     Chrysler TOWN & COUNTRY, VOYAGER, Dodge Caravan - service repair manual 2001-2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1035  1036  1037  1038   ..

 

 

Chrysler Town, Dodge Caravan. Manual - part 1037

 

 

TEST

ACTION

APPLICABILITY

2

With the DRBIII

t, check Transmission DTC’s.

Are there any other Transmission Temperature Sensor related DTCs present?

All

Yes

→ Refer to the Transmission category and perform the appropriate

symptom.
Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

No

→ Go To 3

3

With the DRBIII

t, Check the STARTS SINCE SET counter for P0711.

NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter 2 or less?

All

Yes

→ Go To 4

No

→ Go To 7

4

Turn the ignition off to the lock position.
Remove the Starter Relay.
CAUTION: Removal of the Starter Relay is to prevent a Transmission, NO
RESPONSE, condition and disable the starter.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1A.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
With the Transmission Simulator, turn the Input/Output switch to OFF.
With the DRBIII

t, monitor the TRANS TEMP VOLTS while turning the Thermistor

Voltage switch to all three positions on the Transmission Simulator.
Compare the DRBIII

t readings with the numbers listed on the Transmission

Simulator.
Do the readings on the Transmission Simulator match the DRBIII

t readings ± 0.2

volts?

All

Yes

→ Go To 5

No

→ Go To 6

5

If there are no possible causes remaining, view repair.

All

Repair

Replace Transmission Solenoid/TRS assembly per the Service
Information.
Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

6

Using the schematics as a guide, inspect the wiring and connectors. Repair as
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

All

Repair

Replace the Powertrain Control Module per the Service Informa-
tion. WITH THE DRBIII

t PERFORM QUICK LEARN

Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

184

TRANSMISSION - NGC

P0711-TRANSMISSION TEMPERATURE SENSOR PERFORMANCE —

Continued

TEST

ACTION

APPLICABILITY

7

The conditions necessary to set this DTC are not present at this time.
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wires while checking for shorted and open circuits.
With the DRBIII

t, check the EATX EVENT DATA to help identify the conditions in

which the DTC was set.
Were there any problems found?

All

Yes

→ Repair as necessary.

Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

No

→ Test Complete.

185

TRANSMISSION - NGC

P0711-TRANSMISSION TEMPERATURE SENSOR PERFORMANCE —

Continued

Symptom:

P0712-TRANSMISSION TEMPERATURE SENSOR LOW

When Monitored and Set Condition:

P0712-TRANSMISSION TEMPERATURE SENSOR LOW

When Monitored:

Continuously with the ignition on and engine running.

Set Condition:

The DTC will set when the monitored Temperature Sensor voltage drops

below 0.078 volts for the period of 0.45 seconds.

POSSIBLE CAUSES

RELATED DTC’S PRESENT

TRANSMISSION TEMPERATURE SENSOR SIGNAL CIRCUIT SHORT TO GROUND

TRANSMISSION TEMPERATURE SENSOR

POWERTRAIN CONTROL MODULE

INTERMITTENT WIRING AND CONNECTORS

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many transmission problems. If
the fluid level is low locate and repair the leak then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read Engine DTC’s. Check and repair all Engine DTC’s prior to

performing any transmission symptom diagnostics.
With the DRBIII

t, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.

NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Powertrain Control Module. Some problems are
corrected by software upgrades to the Transmission and Engine software.
NOTE: Check for applicable TSB’s related to the problem.
Perform this procedure prior to Symptom diagnosis.

All

Continue

Go To

2

2

With the DRBIII

t, check Transmission DTC’s.

Are there any Speed Sensor DTCs present?

All

Yes

→ Refer to the Transmission category and perform the appropriate

symptom.
Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

No

→ Go To 3

186

TRANSMISSION - NGC

TEST

ACTION

APPLICABILITY

3

With the DRBIII

t, Check the STARTS SINCE SET counter for P0712.

NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter 2 or less?

All

Yes

→ Go To 4

No

→ Go To 8

4

Turn the ignition off to the lock position.
Remove the Starter Relay.
CAUTION: Removal of the Starter Relay is to prevent a Transmission, NO
RESPONSE, condition and disable the starter.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1A.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
With the Transmission Simulator, turn the Input/Output switch to OFF.
With the DRBIII

t, monitor the TRANS TEMP VOLTS while turning the Thermistor

Voltage switch to all three positions on the Transmission Simulator.
Compare the DRBIII

t readings with the numbers listed on the Transmission

Simulator.
Do the readings on the Transmission Simulator match the DRBIII

t readings ± 0.2

volts?

All

Yes

→ Go To 5

No

→ Go To 6

5

If there are no possible causes remaining, view repair.

All

Repair

Replace Transmission Solenoid/TRS assembly per the Service
Information.
Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

6

Turn the ignition off to the lock position.
Disconnect the PCM C4 harness connector.
Disconnect the Transmission Solenoid/TRS Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance between ground and the Transmission Temperature Sensor
Signal circuit.
Is the resistance below 5.0 ohms?

All

Yes

→ Repair the Transmission Temperature Sensor Signal circuit for a

short to ground.
Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

No

→ Go To 7

187

TRANSMISSION - NGC

P0712-TRANSMISSION TEMPERATURE SENSOR LOW —

Continued

 

 

 

 

 

 

 

Content   ..  1035  1036  1037  1038   ..