Chrysler Town, Dodge Caravan. Manual - part 1002

 

  Index      Chrysler     Chrysler TOWN & COUNTRY, VOYAGER, Dodge Caravan - service repair manual 2001-2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1000  1001  1002  1003   ..

 

 

Chrysler Town, Dodge Caravan. Manual - part 1002

 

 

Symptom:

P0713-TRANSMISSION TEMPERATURE SENSOR HIGH

When Monitored and Set Condition:

P0713-TRANSMISSION TEMPERATURE SENSOR HIGH

When Monitored:

Continuously with the ignition on and engine running.

Set Condition:

The DTC will set when the monitored Temperature Sensor voltage rises

above 4.94 volts for the period of 0.45 seconds.

POSSIBLE CAUSES

TRANSMISSION TEMPERATURE SENSOR SIGNAL CIRCUIT OPEN

TRANSMISSION TEMPERATURE SENSOR SIGNAL CIRCUIT SHORT TO VOLTAGE

TRANSMISSION TEMPERATURE SENSOR

TRANSMISSION CONTROL MODULE

INTERMITTENT WIRING AND CONNECTORS

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many Transmission problems. If
the fluid level is low locate and repair the leak then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read the engine DTC’s. Check and repair all engine DTC’s prior

to performing Transmission Symptom Diagnostics.
With the DRBIII

t, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.

NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

All

Continue

Go To

2

2

With the DRBIII

t, Check the STARTS SINCE SET counter for P0713.

NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter 2 or less?

All

Yes

→ Go To 3

No

→ Go To 8

44

TRANSMISSION - EATX

TEST

ACTION

APPLICABILITY

3

Turn the ignition off to the lock position.
Remove the Starter Relay.
CAUTION: Removal of the Starter Relay is to prevent a Transmission, NO
RESPONSE, condition and disable the starter.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1A.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
With the Transmission Simulator, turn the Input/Output switch to OFF.
With the DRBIII

t, monitor the TRANS TEMP VOLTS while turning the Thermistor

Voltage switch to all three positions on the Transmission Simulator.
Compare the DRBIII

t readings with the numbers listed on the Transmission

Simulator.
Do the readings on the Transmission Simulator match the DRBIII

t readings ± 0.2

volts?

All

Yes

→ Go To 4

No

→ Go To 5

4

If there are no possible causes remaining, view repair.

All

Repair

Replace Transmission Solenoid/TRS Assembly per the Service
Information.
Perform 41TE TRANSMISSION VERIFICATION TEST - VER 1.

5

Turn the ignition off to the lock position.
Disconnect the TCM harness connector..
Disconnect the Transmission Solenoid /TRS Assembly harness connector
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the Transmission Temperature Sensor Signal circuit from
the TCM harness connector to the Transmission Solenoid/TRS Assembly harness
connector.
Is the resistance above 5.0 ohms?

All

Yes

→ Repair the Transmission Temperature Sensor Signal circuit for

an open.
Perform 41TE TRANSMISSION VERIFICATION TEST - VER 1.

No

→ Go To 6

6

Turn the ignition off to the lock position.
Disconnect the TCM harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
Measure the voltage of the Transmission Temperature Sensor Signal circuit in the
TCM harness connector.
Is the voltage above 0.5 volts?

All

Yes

→ Repair the Transmission Temperature Sensor Signal circuit for a

short to voltage.
Perform 41TE TRANSMISSION VERIFICATION TEST - VER 1.

No

→ Go To 7

45

TRANSMISSION - EATX

P0713-TRANSMISSION TEMPERATURE SENSOR HIGH —

Continued

TEST

ACTION

APPLICABILITY

7

Using the schematics as a guide, inspect the wiring and connectors. Repair as
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

All

Repair

Replace the Transmission Control Module per the Service infor-
mation. WITH THE DRBIII

t PERFORM QUICK LEARN AND

REPROGRAM PINION FACTOR.
Perform 41TE TRANSMISSION VERIFICATION TEST - VER 1.

8

The conditions necessary to set this DTC are not present at this time.
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wires while checking for shorted and open circuits.
With the DRBIII

t, check the EATX EVENT DATA to help identify the conditions in

which the DTC was set.
Were there any problems found?

All

Yes

→ Repair as necessary.

Perform 41TE TRANSMISSION VERIFICATION TEST - VER 1.

No

→ Test Complete.

46

TRANSMISSION - EATX

P0713-TRANSMISSION TEMPERATURE SENSOR HIGH —

Continued

Symptom:

P0714-TRANSMISSION TEMPERATURE SENSOR INTERMITTENT

When Monitored and Set Condition:

P0714-TRANSMISSION TEMPERATURE SENSOR INTERMITTENT

When Monitored:

Continuously with the ignition on and engine running.

Set Condition:

The DTC will set when the monitored Temperature Sensor voltage

fluctuates or changes abruptly within a predetermined period of time.

POSSIBLE CAUSES

RELATED DTC’S PRESENT

TRANSMISSION TEMPERATURE SENSOR

TRANSMISSION CONTROL MODULE

INTERMITTENT WIRING AND CONNECTORS

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many Transmission problems. If
the fluid level is low locate and repair the leak then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read the engine DTC’s. Check and repair all engine DTC’s prior

to performing Transmission Symptom Diagnostics.
With the DRBIII

t, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.

NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

All

Continue

Go To

2

2

With the DRBIII

t, check Transmission DTC’s.

Are there any Speed Sensor and/or other Temperature Sensor DTCs present?

All

Yes

→ Refer to the Transmission category and perform the appropriate

symptom.
Perform 41TE TRANSMISSION VERIFICATION TEST - VER 1.

No

→ Go To 3

47

TRANSMISSION - EATX

 

 

 

 

 

 

 

Content   ..  1000  1001  1002  1003   ..