Chrysler New Yorker. Manual - part 578

TEST TC-32A

REPAIRING - 1/1 O2S STAYS AT CENTER

Perform TEST DTC Before Proceeding

1/1 RIGHT BANK UP

T

R

O

U
B

L

E

C

O

D

E

T

E
S

T

S

148

TEST TC-32A

REPAIRING - 1/1 O2S STAYS AT CENTER

Perform TEST DTC Before Proceeding

*Perform Verification TEST VER-2A.

**Check connectors - Clean / repair as necessary.

START THE ENGINE 

START TEST AND ALLOW IT 

TO 

TC-32A.

REACH NORMAL 

OPERATING

TEMPERATURE. 

USING THE DRB IN 
ACTUATOR TESTS, 

WITH THE DRB, READ 

IS THE 1/1 OXYGEN 

NO 

CONTINUE TEST 

SET THE ENGINE RPM

THE 1/1 OXYGEN 

SENSOR STATE

TC-32A ON THE

TO 1500.

SENSOR STATE. 

SWITCHING? 

NEXT PAGE.

YES

AT ANY TIME DOES 

REPAIR THE OPEN 

WIGGLE 1/1 OXYGEN 

WHILE WIGGLING THE

THE 1/1 OXYGEN 

YES HARNESS OR CONNECTOR

SENSOR CONNECTOR &

HARNESS, MONITOR

SENSOR STATE STAY 

THAT CAUSED THE

HARNESS. 

THE DRB DISPLAY. 

LOCKED AT CENTER?

OXYGEN SENSOR STATE
TO STAY AT CENTER.* 

NO 

AT THIS TIME, THE

USING THE

CONDITION REQUIRED 

SCHEMATIC AS A

WERE ANY PROBLEMS 

YES

REPAIR AS 

TO SET THE TROUBLE

GUIDE, INSPECT THE

FOUND? 

NECESSARY.*

CODE IS NOT PRESENT. 

WIRING AND

CONNECTORS.

NO 

TEST COMPLETE.* 

T

R

O

U
B

L

E

C

O

D

E

T

E
S

T

S

149

TEST TC-32A

CONTINUED - REPAIRING - 1/1 O2S STAYS AT CENTER

1/1 RIGHT BANK UP

FIG. 1

1/1 RIGHT BANK UP

FIG. 2

T

R

O

U
B

L

E

C

O

D

E

T

E
S

T

S

150

TEST TC-32A

CONTINUED - REPAIRING - 1/1 O2S STAYS AT CENTER

*Perform Verification TEST VER-2A.

**Check connectors - Clean / repair as necessary.

TEST TC-32A 

CONTINUED FROM 

THE PREVIOUS 

TURN IGNITION OFF. 

PAGE.

DISCONNECT THE 1/1

IS ANY TERMINAL 

O2 SENSOR HARNESS

DAMAGED, CORRODED,

YES

REPAIR AS 

CONNECTOR.** PUSHED 

OUT OR 

NECESSARY.*

MISWIRED?

SEE GENERAL INFO 4.4

NO 

USING AN OHMMETER,

MEASURE THE

GROUND CIRCUIT AND

IS THE RESISTANCE 

YES

REPAIR THE OPEN 

RESISTANCE BETWEEN

GROUND.

ABOVE 5.0 OHMS?

1/1 O2 SENSOR 

THE 1/1 O2 SENSOR...

GROUND CIRCUIT.*

FIG. 1

NO 

KEY ON. CONNECT A

USING THE DRB IN 

JUMPER WIRE BETWEEN

SENSORS, READ THE

IS THE VOLTAGE

YES

REPLACE THE 1/1 O2 

THE 1/1 O2 SENSOR 

1/1 O2 SENSOR 

ABOVE 1.0 VOLT?

SENSOR.* 

SIGNAL CIRCUIT AND

VOLTAGE. 

B+. FIG. 1

NO 

KEY OFF, DISCONNECT 

THE PCM CONNECTOR

DISCONNECT THE

HARNESS CONNECTOR.** JUMPER 

WIRE.

SEE GENERAL INFO 4.1

USING AN OHMMETER,

...FROM THE 1/1 O2 

MEASURE THE 1/1 O2 

SENSOR CONNECTOR TO 

IS THE RESISTANCE 

YES

REPLACE THE

SENSOR SIGNAL 

THE PCM CONNECTOR. 

BELOW 5.0 OHMS?

POWERTRAIN CONTROL

CIRCUIT... 

MODULE.* 

FIG. 2

NO 

REPAIR THE OPEN 

1/1 O2 SENSOR 

SIGNAL CIRCUIT.*

T

R

O

U
B

L

E

C

O

D

E

T

E
S

T

S

151