Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 993

 

  Index      Chrysler     Chrysler 300/300 Touring/300C, Dodge Magnum - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  991  992  993  994   ..

 

 

Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 993

 

 

4. Disengage the outboard retaining clip, and rotate

the IPM to access wire harness connectors.

5. Disconnect wire harness connectors from IPM.

6. Disengage the two inboard retaining clips.

7. Remove IPM from vehicle.

INSTALLATION

NOTE: A battery reconnect procedure must be per-
formed anytime the battery has been discon-
nected.

(Refer

to

8

-

ELECTRICAL/BATTERY

SYSTEM - STANDARD PROCEDURE).

1. Position Integrated Power Module (IPM) to vehicle.

Engage the three retaining clips.

8W - 97 - 4

8W-97 POWER DISTRIBUTION

LX

2. Disengage the outboard retaining clip and rotate

the IPM to access wire harness connectors.

3. Connect electrical harness connectors to IPM.

4. Connect battery cable to IPM.

5. Install and tighten retaining nut.

6. Close the battery cable nut cover.

7. Connect battery negative cable (2).

LX

8W-97 POWER DISTRIBUTION

8W - 97 - 5

POWER DISTRIBUTION CENTER

DESCRIPTION

The majority of electrical system fuses and relays are
housed in the two Power Distribution Centers (PDC).
One is located in the engine compartment, combined
with the Front Control Module (FCM) to form the Inte-
grated Power Module (IPM). The other is next to the
battery at the rear of the vehicle. The PDC located
next to the battery is replaced only as part of the body
wiring harness.

8W - 97 - 6

8W-97 POWER DISTRIBUTION

LX

POWER OUTLET

DESCRIPTION

Sedans are equipped with two 12–volt electrical outlets. Wagons are equipped with three 12–volt electrical outlets.
The outlets are located in the following locations:

Cargo area right quarter trim panel (wagons only).

Inside the center console.

Next to the ash receiver in the center stack.

The outlets in the console and quarter trim panel have power at all times, and include tethered covers. The outlet
in the ash receiver tray is shipped with power available only when the ignition is in the ON position. This outlet can
be changed to provide power at all times by moving a fuse in the fuse block.

REMOVAL

NOTE: A battery reconnect procedure must be performed anytime the battery has been disconnected. (Refer
to 8 - ELECTRICAL/BATTERY SYSTEM - STANDARD PROCEDURE).

1. Disconnect and isolate the battery negative cable.

2. Pull the cigar lighter knob and element out of the cigar lighter receptacle base, or unsnap the protective cap from

the power outlet.

3. Look inside the cigar lighter or power outlet and note the position of the rectangular retaining bosses of the

mount that secures the receptacle base.

4. Insert a pair of external snap ring pliers into the cigar lighter or power outlet receptacle base and engage the tips

of the pliers with the retaining bosses of the mount.

5. Squeeze the pliers to disengage the mount retaining bosses from the receptacle base and, using a gentle rock-

ing motion, pull the pliers and the receptacle base out of the mount.

6. Pull the receptacle base away far enough to access the wire harness connector.

7. Disconnect the wire harness connector from the cigar lighter or power outlet.

8. Remove the cigar lighter or power outlet.

INSTALLATION

NOTE: A battery reconnect procedure must be performed anytime the battery has been disconnected. (Refer
to 8 - ELECTRICAL/BATTERY SYSTEM - STANDARD PROCEDURE).

1. Connect the wire harness connector to the cigar lighter or power outlet receptacle base connector receptacle.

2. Install the cigar lighter or power outlet mount into position.

3. Align the splines on the outside of the cigar lighter or power outlet receptacle base connector receptacle with the

grooves on the inside of the mount.

4. Press firmly on the cigar lighter or power outlet receptacle base until the retaining bosses of the mount are fully

engaged in their receptacles.

5. Install the cigar lighter knob and element into the cigar lighter receptacle base, or the protective cap into the

power outlet receptacle base.

6. Connect the battery negative cable.

LX

8W-97 POWER DISTRIBUTION

8W - 97 - 7

 

 

 

 

 

 

 

Content   ..  991  992  993  994   ..