Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 270

 

  Index      Chrysler     Chrysler 300/300 Touring/300C, Dodge Magnum - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  268  269  270  271   ..

 

 

Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 270

 

 

B221F-AMPLIFIER INTERNAL

For a complete wiring diagram Refer to Section 8W.

When Monitored:

With the ignition on.

Set Condition:

The Amplifier detects a software checksum test failure.

Possible Causes

AMPLIFIER

Diagnostic Test

1.

REPLACE THE AMPLIFIER

When this code is set, the Amplifier must be replaced.

Repair

Replace the Amplifier in accordance with the Service Information.

Perform the BODY VERIFICATION TEST-VER 1.

8A - 6

AUDIO - ELECTRICAL DIAGNOSTICS

LX

B1488–CABIN EQ MISMATCH PERFORMANCE

For a complete wiring diagram Refer to Section 8W.

When Monitored:

With the ignition on.

Set Condition:

If the cabin EQ message is incompatible with the EQ’s stored in the amplifier for 10 consecutive cycles, then
the amplifier will set this DTC.

POSSIBLE CAUSES

NO COMMUNICATION WITH FRONT CONTROL MODULE

ACTIVE FCM DTCs

AMPLIFIER

Diagnostic Test

1.

CHECK FOR AN INTERMITTENT CONDITION

Turn the ignition on.

Turn the radio on.

With the scan tool, erase Amplifier DTCs.

With the scan tool, reset the amplifier.

With the scan tool, read Amplifier DTCs.

Does the scan tool display active: B1488–CABIN EQ MISMATCH PERFORMANCE?

Yes

>> Go To 2

No

>> The conditions that caused this code to set are not present at this time. Using the wiring diagram/sche-

matic as a guide, inspect the wiring and connectors.

Perform BODY VERIFICATION TEST VER-1.

2.

CHECK AMPLIFIER BUSSED INPUTS/OUTPUTS

With the scan tool in Amplifier Data Display, read the Cabin EQ# settings in the Bussed Inputs and Bussed Outputs
Sections.

NOTE: The Cabin EQ# settings in the Inputs/Outputs section should match one another. The Cabin EQ# in
the Inputs section is the information that is received form the FCM. The Cabin EQ# in the Outputs section
is the information that is Stored in the Amplifier’s memory.
The Cabin EQ# settings are as follows:

• •

$51: HB Premium 1 (w/o Subwoofer)

• •

$52: HB Premium 2 (with Subwoofer)

Do the Cabin EQ# settings match one another?

Yes

>> Replace the Amplifier in accordance to the service information.

Perform the BODY VERIFICATION TEST-VER 1.

No

>> Go To 3

LX

AUDIO - ELECTRICAL DIAGNOSTICS

8A - 7

3.

VERIFY COMMUNICATION WITH FRONT CONTROL MODULE

With the scan tool in ECU VIEW, read active modules on the bus.

Does the scan tool show the Front Control Module active on the bus?

Yes

>> Go To 4

No

>> Refer to the Communication category for the related symptoms.

Perform the BODY VERIFICATION TEST VER 1.

4.

CHECK FRONT CONTROL MODULE FOR ACTIVE DTCs

With the scan tool, erase FCM DTCs.

Turn the ignition off. Wait approximately 10 seconds.

Turn the ignition on.

With the scan tool, read FCM DTCs.

Are any active DTCs present?

Yes

>> Refer to symptom list for problems related to the Front Control Module.

Perform the BODY VERIFICATION TEST VER 1.

No

>> Replace the Front Control Module in accordance with the Service Information.

Perform the BODY VERIFICATION TEST-VER.1

8A - 8

AUDIO - ELECTRICAL DIAGNOSTICS

LX

B1460-CHANNEL 1 AUDIO SPEAKER OUTPUT CIRCUIT PERFORMANCE

For a complete wiring diagram Refer to Section 8W.

When Monitored:

With the ignition on.

Set Condition:

This DTC will set if a DC offset occurs on the output channel, the amplifier shall set a DTC after a maturity
rate of 5 ±1 sec.

Possible Causes

AMPLIFIER

Diagnostic Test

1.

CHECK FOR AN INTERMITTENT CONDITION

Turn the ignition on, then off, and then on again.

With the scan tool, read Amplifier DTCs.

Does the scan tool display active: B1460-CHANNEL 1 AUDIO SPEAKER OUTPUT CIRCUIT PERFOR-
MANCE?

Yes

>> Replace the Amplifier in accordance with the service information.

Perform BODY VERIFICATION TEST VER-1.

No

>> The conditions that caused this code to set are not present at this time. Using the wiring diagram/sche-

matic as a guide, inspect the wiring and connectors.

Perform BODY VERIFICATION TEST VER-1.

LX

AUDIO - ELECTRICAL DIAGNOSTICS

8A - 9

 

 

 

 

 

 

 

Content   ..  268  269  270  271   ..